Metel 2G 2S.0.3.F Bedienungs- und Wartungsanleitung
www.metel.eu 1/23
www.iplog.eu
REV-202204
Industrial PoE+ Managed witches 2G
2 .0.3.F
2G
2 .0.3.F PoE NMPMODBU VLAN R TPONVIF 802.1X
Typical connection
2G-2 .0.3.F-BOX-PoE
LAN-RING 20G
LAN-RING 2G
For Available FP Modules Visit www.metel.eu
2G-2 .0.3.F-BOX-PoE 2 0 3 2 1 2
AVAILABLE PORT : FP GE FE D/AI RELAY R 485
upply without PoE 10-60VDC/10-30VAC, with PoE 48-57VDC
upply with PoE+ 52-57VDC (15…25W), with PoE++ 53-57VDC (>25W)
2G-2 .0.3.F-BOX-PoE 1-988-220 10-60VDC/10-30VAC
Holder for Mounting to DIN35 and Flat urface is Included.
PRODUCT NAME CODE NOTE
Vertical Mounting to DIN35 Mounting to a Flat urfaceMounting to DIN35
v 2x FP lot with upport of 100/1000BA E-X
v 3x Fast Ethernet Port with PoE IEEE 802.3af/at
max. 30W per Port
v Total PoE Power Over All Ports is 90W
v 2x R 485/Modbus-RTU Buses
v 2x Digital/Alarm Inputs
v 1x Programmable Relay Output
v 2 Independent Power Inputs
v Redundant Topology LAN-RING, R TP
v Event Management with upport:
HTTP/ONVIF Client, E-mail, IP Watchdogs, ETH
Events, TCP, Modbus, DIO, Balanced Loops…
v Visualization oftware upport
v Encrypted Management via LAN/Local U B
v urge Protectors up to 150A (8/20µs)
v VLAN, Qo , NMP, MTP, NTP, IGMP, R TP,
LLDP, 802.1X, Mirror, Remote Acces IP Table
v Maximum tart Time 15s
v Operating Range −40°C to + 70°C
v Operating Range of Components -40°C to + 85°C
LAN-RING 2G
1x MM / M Fiber Fast Ethernet erial Buses Other IO
Gigabit Ethernet Fast Ethernet with PoE
I&HAS
& ACS
REDO AO
AI DI
Modbus RTU
RE DOAOAIDI
RE
DO
AO
AI DI RE
DO
AO
AI DI
I&HAS
& ACS
Modbus RTU
Typical Connection of LAN-RING ystem Versatility
www.metel.eu 2/23
www.iplog.eu
REV-202204
Industrial PoE+ Managed witches 2G
2 .0.3.F
2G
2 .0.3.F PoE NMPMODBU VLAN R TPONVIF 802.1X
Further
info
pages
12 - 13
16 - 18
Further
info
pages
15,
21 - 22
BX-100-20-W4-L 4-101-020 C / PC 20 / 5 km
BX-100-20-W5-L 4-101-010 C / PC 20 / 5 km
BX-1000-20-W4-L 4-101-120 C / PC 20 / 2 km
BX-1000-20-W5-L 4-101-110 C / PC 20 / 2 km
BX-1000-60-W4-L 4-101-122 C / PC 60 / - km
BX-1000-60-W5-L 4-101-112 C / PC 60 / - km
PRODUCT NAME CODE CONNECTOR RANGE(1)
2x FP lots with 100/1000BA E-X upport
Switches 2G-2S.0.3.F have 2 SFP slots universally usable
both for SFP modules ME EL (tab on the right) and for SFP
modules of other manufacturers. he main advantages of
ME EL SFP modules are:
- bidirectional CWDM data transmission over one fiber
- used components with a range from −40 to +85°C
- SM / MM universal (all versions -20-)
- minimum warranty period 5 years (1) singlemode (9/125µm) / multimode (50/125µm)
3x Fast Ethernet Port with PoE up to 30W per Port
Fast Ethernet ports support 10BASE- , 100BASE- standards including Auto negotiation,
MDI/MDI-X and PoE standards 802.3af/at up to 30W per port. he distri-bution of power to
individual ports is set in the Simuland.v4 application. he ports due to increased reliability
are protected by surge protection up to 150A in a floating connection.
& The maximum total power consumption of PoE over all ports is 90W.
2x R 485/Modbus-RTU Buses
he switches are equipped with two RS485 buses enabling the connection of Modbus R U IO
modules and sensors, selected types of I&HAS systems and other devices.
& The transmission of system buses of I&HA systems is certified according to EN50131-1.
Further
info
page
8-9
2x Digital/Alarm Inputs
Digital/alarm inputs are mainly used for connecting button tampers, PIR sensors and others.
SIMUland management software allows them to be used to set up a range of automatic
actions. In addition, the inputs are monitorable via the SNMP protocol.
Further
info
page
14
1x Programmable Relay Output
Programmable relay output is used to signal faults (eg open circuit), control el. locks,
contactors and signaling elements. In addition, the relay can be controlled from software
superstructures, IPLOG PLC SNMP or MODBUS protocol, or EVEN MANAGEN switches.
Further
info
page
18
2 Independent Power Inputs
he switches have 2 independent power inputs 10 to 60VDC and one 10-30VAC input.
ypical applications with backup power supply are systems where the switch is part of the IP
CC V system and at the same time transmits the system bus of the PZ S system. he inputs
are protected against overvoltage.
Further
info
page
5
LAN / U B Management
In addition to secure LAN management, each LAN-RING switch has a USB-A connector for
local management via the SIMULand application. he USB connector also allows you to reset
the switch to factory settings. he inputs are protected against overvoltage.
www.metel.eu 3/23
www.iplog.eu
REV-202204
Industrial PoE+ Managed witches 2G
2 .0.3.F
2G
2 .0.3.F PoE NMPMODBU VLAN R TPONVIF 802.1X
upported Formats 100/1000 BA E-LX, BA E-BX M A Compatibility
FP lots Number 2
LAN Number 3 FE
Overvoltage Protection FE ports: up to 150 A in the wave 8/20μs - more p. 22
upported Formats FE ports: 10BaseT, 100BaseTx
With PoE+ up to 30W 52 - 57 52 - 57 VDC
Power Consumption Max. 4 W without PoE supply to FE ports
Parameter Value Unit Note
Connector RJ45
Power upply Main Input Back-up Input
Max. Load 62,5VA (30W) / 1A / 60V Resistive Load
Overvoltage Protection 1500 W 10/1000µs
torage Range –40…+70 °C
Environment Operational Range –40...+70 °C Temperature of Environment
Humidity Max. 95 % Non-condensing
Management Application IMULand Windows Applications
Without PoE 10 - 60 / 10 - 30 10 - 60 VDC/AC
With PoE up to 15,4W 48 - 57 48 - 57 VDC
Weight 0,65 kg
Relay Output Type of Contact 1x Change-Over
Analog 0 - 30kΩ for Balanced Loops
Overvoltage Protection 30 A 8/20μs
peed Max. 57,6 kbps
R 485 Number 2
Digital inputs Number 2
Mode Digital - NC / NO
The producer retains the right to change any technical parameters without previous written or published notification.
Certification CE, TUV
Technical Parameters compatibility
Electromagnetic Compatibility compatibility
tandard Tested Level – Criteria Note
EN 55024 - Information technology equipment - Immunity characteristics - Limits and methods of measurement
EN 61000-4-2 – Contact Discharge Level 4 – Criteria B 8kV
EN 61000-4-2 – Air Discharge Level 4 – Criteria B 15kV
EN 61000-4-4 – Bursts Level 4 – Criteria B 4kV / 5kHz
EN 61000-4-5 – urge Immunity Level 4 – Criteria B 4kV, BU , GE and DI Level 3 (2kV)
EN 61000-4-8 – Magnetic Field 50 Hz Level 5 – Criteria A 100A
EN 61000-4-9 – Pulse Magnetic Field Level 5 – Criteria A 1000A
EN 55022 – Radiated Emission Class A
www.metel.eu 4/23
www.iplog.eu
REV-202204
Industrial PoE+ Managed witches 2G
2 .0.3.F
2G
2 .0.3.F PoE NMPMODBU VLAN R TPONVIF 802.1X
Dimensions of 2G-2 .0.3.F universality
REV: 201406 – Default
201504 – Added Installation GBIC Modules
201904 – Design change, added 802.1X protocol, galvanically separated cover from the electronics
202204 – Change PoE circuit
www.metel.eu 5/23
www.iplog.eu
IMULand.v4 - Configuration oftware with GUI
SIMULand.v4 is a freeware software for configuring all LAN-RING devices. It
excels in intuitive GUI and advanced tools for efficient management of
even ver large s stems.
v Online / Offline configuration of all LAN-RING devices in the GUI
v Automatic search for available devices on the LAN
v Automatic detection and rendering of system topology
v U B console for local device management
v Download menu for bulk downloads of configurations from device to IMULand
v Upload menu for bulk uploads of the prepared configurations to the devices
v Encrypted communication protected by a hash algorithm
v IMULand includes firmware for upgrading all supported devices
v In the tatus menu, you can monitor the operating status of the device online
v Quick config for accelerated PoE configuration, IP address assignment ...
v Access to the device log
Y TEM REQUIREMENT
Operating system Windows 8, 10 – 32/64bit
Monitor Full HD
RAM 2GB or more, depending on the size of the project
Language versions CZ, EN PL, UA
The manufacturer reserves the right to change technical parameters without prior notice.
SIMULand.v4 is a Windows desktop software with a GUI for bulk configuration of LAN-RING
devices in Online, Offline or USB mode. It also includes a number of tools for network
communication analysis, including fully automatic detection of network topology with display
of optical and metallic connections, amount of transmitted data in Mbps in connections,
number of dropped packets on ports, PoE status, power status, input/outputs/ports status.
Processor Intel Core 2 DUO 2GHz / AMD X2 2GHz or faster
LI T OF UPPORTED DEVICE
BB-x.x.x-22
200M-1.0.4.E-W4
200M-1.0.4.E-W4-PoE+
200M-1.0.4.E-W5
200M-1.0.4.E-W5-PoE++
200M-2.0.1.E
200M-2.0.4.ECA
200M-2.0.4.ECB
200M-2.1.0
200M-2.1.0.E
200M-2.1.4
200M-RS.E4
200M-RS.E5
200M-EVA
200M-EVA8
200M-ADAM
200M-ADAM8
2G-0.1.4
2G-0.1.4.E
2G-0.1.8.E
2G-0.1.8.EC
2G-1.0.4.E-W4
2G-1.0.4.E-W4-PoE++
2G-1.0.4.E-W5
2G-1.0.4.E-W5-PoE++
2G-2.0.1.E
2G-2.0.4.ECA
2G-2.0.4.ECB
2G-2.1.0
2G-2.1.0.E
2G-2.1.0.EB
2G-2.1.4
2G-RS.E4
2G-RS.E5
2G-RS.E6
RING-IO
LAN-485
200M-2.1.4.E
200M-2.1.4.E ++
2G-2.1.4.E
2G-2.1.4.E ++ 2G-2.1.7.E
2G-2.3.0.E
2G-6S.1.16.E
2G-6S.1.16.F-UNI /1U,
2G-10S.F-UNI /1U
2G-2S.0.3.F-BOX-PoE
2G-2S.0.3.F-BOX PoE(M-PoE)
2G-2S.0.3.FC-BOX
2G-2S.3.0.F-BOX
2G-2S.0.2.F-BOX-PoE
2G-2S.0.2.F-BOX-PoE
2G-2S.0.2.F-BOX-PoE-PP
2G-2S.1.4.F-BOX
2G-2S.1.4.F-BOX-PoE-PP
2G-2.7.1.0.F-BOX
2G-2C.0.8.F-BOX-PoE-PP
2G-1C.0.8.FC-BOX-PoE-PP
2G-2C.8S.0.0.F-BOX
20G-2X.8.0.F-BOX
miniLAN-232
miniLAN-485
IPLOG-DEL A-1
IPLOG-DEL A-2
IPLOG-DEL A-3
IPLOG-DEL A-1-Geuteb.
IPLOG-DEL A-1-Eza
IPLOG-DEL A-1-Redwall
IPLOG-DEL A-1-Elfar
IPLOG-DEL A-1-R62
IPLOG-DEL A-1-Peridect
IPLOG-DEL A-3-Peridect
IPLOG-DEL A-3-Valert
IPLOG-DEL A-VoIP
IPLOG-DEL A-2-GSM
IPSEN-D6
IPSEN-D16
IPSEN-H2O
IPSEN- 1
IPSEN- H1
IPSEN-BL8I
IPSEN-BL8O
www.metel.eu 6/23
www.iplog.eu
LAN-RING for Ring Topology
One of the fundamental elements of the security system LAN-RING is fast data forwarding to a back-up
line. Since 2008, this function has been performed by LAN-RING.v1 protocol with a switchover time of
30ms from the failure. Each ring in the system has a unique ID and one switch with the MAS ER function
(controls the ring). he higher port of the MAS ER switch is normally set to a BLOCKING mode, hence
preventing a loop. A port in BLOCKING mode receives only LAN-RING frames and blocks the other data
(back-up line). If a failure occurs, the state of the blocked port changes to FORWARDING and starts to
transmit all data.
Initial tate Failure Failure Resolution Final tate
During the failure creation and resolution, there are 2 short interruptions in the route. he second
interruption provides the switchover from the back-up line back to the MAS ER switch. Since, the end
of 2014, a new innovative version of LAN-RING.v2 is available. he switch which has the MAS ER function
which controls the ring. In the case of a failure, the MAS ER function moves to the switch next to the
failure. From the origin of the problem to the time of its removal, only one interruption occurs of up to
maximum of 30ms.
Initial tate Failure Failure Resolution = Final tate
& The switchover time to the back-up line is for LAN-RING protocols slightly dependent
on the number of switches connected in the ring. With each switch connected to the ring,
the reconfiguration time increases by only about 6μs!
MA TER
MA TER
MA TER MA TER MA TER
Interruption
When a Failure
Occurs
Interruption
During Failure
Resolution
MA TER MA TER
Port in
BLOCKING
Mode
Port in
BLOCKING Mode Interruption
When a
Failure
Occurs
R TP and R TP-M for ME H Topology
he RS P-M protocol is a time-optimized version of
the general RS P protocol with which it is backward
compatible. In addition, it meets the requirements of
safety and automation systems to quickly secure a
backup route in the event of a fault and:
v is fully compatible with RS P according to IEEE
802.1D-2004
v supports MESH topology
v reduces reconfiguration times to a minimum
DP DP
DP
DP
DP
DP RP
RP RP
RP
RP
BP
BP
RP RP – root port
DP – designated port
BP – blocked port
Redundant Topology
www.metel.eu 7/23
www.iplog.eu
NAME TYPE NOTE
The LAN-RING industrial switch software includes the Event Management
tool set in the Extension menu. The user can set up to 64 automatic
actions. The event management switch is also able to communicate
directl with the PLC IPLOG where the control program written in the FBD,
LD, ST or IL language described in IEC 61131-3 is running. Event
management has the potential to significantl increase the value of our
s stem and customize the s stem to the customer's requirements.
MODBU RTU/TCP INPUT and OUTPUT (DI, AI, BI, RE, AO, DO, BO) Up to 16 IO Modules and ensors on R 485 Bus
LOCAL IO INPUT and OUTPUT (BI, DI, RE) Local Inputs and Outputs LAN-RING witches
ETHERNET EVENT INPUT and OUTPUT Protocol for Transmission of tatuses Over LAN
NMPv2/v3 INPUT and OUTPUT Protocol for Transmission of tatuses Over LAN
TCP EVENT INPUT Receives TCP Messages From Cameras etc.
RE TART POE OUTPUT Restarts PoE with IP Watchdog
EMAIL OUTPUT ends E-mails
ONVIF OUTPUT Controls Cameras
HTTP OUTPUT ends HTTP Commands to CAM, NVR, PLC...
IP WATCHDOG INPUT Monitors IP devices
OPTICAL RING INPUT Monitors Optical RINGs tates
FE / GE / FO PORT INPUT and OUTPUT Monitors Port tates, Port Control
Nastavení
výstupu
Automatic Actions
LAN-RING witch
Loading
of the witch Input
Processing the
set Action
et the witch
Output
PLC IPLOG Control Program
Loading
of PLC
Inputs
et the
PLC
Outputs
Loading of
External Inputs
ettings of
External Outputs
Motion Detection witch … Activates Local RELAY
… ends an E-mail
… ends a NMP Trap
… ends a ONVIF command
Restart PoE at
Freezing Detection
Modbus T/RH ensor
Event Management - Overview
Examples of Automatic Actions
Available Inputs and Outputs
A unique set of tools in the EX ENSION menu of LAN-RING switches and monitoring units IPLOG allow
you to set a whole range of automated actions independent of external software. he table below
provides an overview of supported inputs and outputs that can be used to set automatic actions.
Connection to a PLC IPLOG
www.metel.eu 8/23
www.iplog.eu
ETH
E H events are used for status transmission over the LAN-RING network. Events differ from each other by
a so-called ID identifier in the range of 1 to 999. An E H event with the same identifier must be set on the
side that sends and receives the event.
Example The switch sends the status of input IN1 as an ETH event with ID#87.
Example The switch receives ETH events with ID#87, which control the relay.
Menu „Extension/ETH-IO“
he setting of the communication parameters for status transfer between
inputs and outputs is configured in the "Extension / E H-IO" menu. So-called
multicast packets are used for transmission, which enable the transmission of
information to multiple recipients.
Receive address - multicast address for receiving packets
Priority - QoS priority assigned to outgoing packets
VLAN ID - VLAN tag for sending and receiving packets
Transmit address 1 to 5 - multicast address for sending packets
Application note I O transfer between switches
Event Management - ETH, DIGITAL
DIGITAL
DIGI AL inputs allow you to set automatic actions with digital inputs of switches IN1 and IN2.
DIGITAL MODE - supported modes
Close - event is triggered by closing the input (connection of IN to GND)
Open - the event is triggered by opening the input
Direct - the input status is sent every 3 seconds. When there is a change, this change is sent immediately
Change - the event is triggered by closing or opening the input
Example Switch on input No. 2 calls up the setting of Preset No. 12 on camera No. 3 (Onvif command).
Menu „Extension/Input/Digital“
Label - input naming (stored in the SIMULandv4 project)
Negation - input negation
Minimal pulse duration (s) - minimum input on/off length
& The METEL-COMIO-DIO-MIB file, which also contains NMP TRAP
permissions, is available for monitoring NMP inputs.
www.metel.eu 9/23
www.iplog.eu
Event Management - ALARM
ALARM
ALARM inputs are digital inputs IN1 and IN2 switched to alarm mode in the "Extension / Input / Alarm"
menu. Once activated, they function as standard alarm inputs and support PIR connections with EOL
resistors (up to 8 states per input).
MODE - supported modes
tate is / tate is not - Balanced loop is/is not in state ...
Direct is / Direct is not - he loop status is sent every 3 seconds. When the entered input state
changes, this change is sent immediately.
Change is / Change is not - If there is/did not change from the state.
tate direct - he current state of the loop is sent every 3 seconds. When the loop state changes, this
information is sent immediately.
tate change –- Response to state change only.
Value direct - he current value of the balanced loop is sent every 3 seconds. When the value of the
balanced loop changes, the information is sent immediately.
Value change - he information is sent when the value of the balanced loop changes.
AC IVE - resistance ranges defined in "Extension / Input / Alarm". In total, 8 ranges up to a maximum of
30,000 Ohms are available for each input.
Example If the resistance of the alarm loop at input IN1 corresponds to Sabotage (short), an HTTP user
command URL1 ("Camera / User commands") with a value of 2 is sent to camera No. 4.
Examples of alarm loop balancing: Menu with alarm loop settings:
& The METEL-COMIO-EZ -MIB file is available for
monitoring alarm inputs via the NMP protocol,
which also contains NMP TRAP permissions.
1k0 3k0
1k0
ALARM TAMPER FAULT
1k0 12k
ALARM FAULT ANTIMA K. 1k0
3k0
ABOTAGE
www.metel.eu 10/23
www.iplog.eu
LAN-RING
Optical ring status monitoring with LAN-RING protocol.
MODE - supported modes
Close - the event is triggered when the ring closes
Open - the event is triggered if the ring opens
Direct - the status of the optical ring is sent every 3 seconds. When the status changes, the change is sent
immediately
Change - the event is triggered by closing or disconnecting the optical ring
Example The state of the ring is transmitted to the relay output, which is connected to the signaling LED
light. In case the ring is disconnected, the light is active.
& A METEL-RING-MIB file is available for monitoring the status of NMP rings, which also contains
NMP TRAP permissions.
Event Management – LAN-RING, TCP, MIO , EXP-C
TCP
he switch can listen on the specified CP port set in the "Extensions / CP" menu. If a device on the
network sends a notification to the switch's IP address and the specified CP port, the switch can respond
to it with the created automatic action.
MODE - supported modes
Matches - the pattern entered must match the text that came
Contains - the received text contains the specified pattern
tarts - the received text starts with the specified pattern
Ends - the received text ends with the specified pattern
Example In case the switch intercepts a TCP notification from the network with the entered text
(pattern), it will control the camera No. 2.
MIO , EXP-C
Modes for communication with discontinued IO modules. More information at support@metel.eu
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Metel Schalten Handbücher
