Meteor 8310 Bedienungsanleitung

Fun Imager

(model 8310)

User Manual

v1.01

NOTICE:

This equipment has been tested and complied with

the limits for a Class a digital device, pursuant to

Part 15 of the FCC Rules. These limits are

designed to provide a reasonable protection

against harmful interface when the equipment is

operated under a commercial environment. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may

cause harmful interface to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interface in which case the

user will be required to correct the interface at his

own expenses.

Note

: All brands and trademarks shall belong to their

respective owner.

This device complies with Part 15 of the FCC

Rules. Operation shall be subject to the following

two conditions:

(1) This device may not cause harmful interface,

and

(2) This device must accept any interface received,

including interface that may cause undesirable

operation.

Note

: Specification is subject to changes without

notice.

Using the Scanner

8110/8150/8250/8310/8312

The Scanner can automatically scan barcode at a

distance. Simply aim and pull the trigger. Code scanning

is performed along the center of the light bar emitted

from the reading window. This bar must cover the entire

code.

Successful scanning shall be obtained by tilting the

scanner with respect to the barcode to avoid direct

reflections that impair the reading performance,

especially for 2D barcode.

Recommended Steps

When the required settings have been configured, all

settings are stored in non- volatile memory of scanner

after reading EXIT Label. Recommended steps are as

follows.

1) Set right host interface for your scanner.

(The scanner is in factory default shown as bold

label)

2) Set interface to optimize protocol of scanner with

your host in interface section.

3) Set system control of scanner, such as specific

adjustments double confirm, power saving, indicator

and scanning mode which you prefer usage in

system control section.

4) Set code options of scanner for your usage in code

option section. You must make sure to enable the

symbology first, then Min./Max. code length, code

ID checksum and truncate digits are also converted.

5) Set string format of the scanner, such as preamble,

postamble Prefix, suffix, code ID and code name

transmission for your application in string format

section.

Note:

If still not work properly. Please contact your dealer

for further information.

CONTENTS

Chapter 1 Introduction

Introduction…………………………..………………. 1

Default Setting ………………………………………. 2

Scanner8110 specification ………..…………….. 4

Scanner8150/8250/8310/8312 specification 7

Programming the Scanner….…………………….. 10

Chapter 2 Parameter Setting

Interface……………………………………………….… 12

Interface Selection ………………………………….. 12

Keyboard wedge ……………………………………. 13

RS-232 …………………………………………….…. 18

Wand Emulation …………………………….………. 21

Pin Assignments ……………………………………. 24

System Control………………………………………. 26

Scan …………………………………………………. 26

Indication …………………………..………………… 30

Code Option…………………………………….……… 32

UPCA ……………………………………..…………. 32

UPCE ………………………………………………… 36

EAN-13 ………………………………………………. 40

EAN-8 ………………………………………………… 44

Code 39 ……………………………………………… 48

Interleaved 2 of 5 …………………………………… 52

Industrial 2 of 5 ……………………………………… 54

Matrix 2 of 5 Eur …………………………………… 56

Codabar ……………………………………………… 58

Code-128 …………………………………………… 61

Code-93 ……………………………………………… 65

Code-11 ………………………………………….…… 68

MSI/Plessey …………………………………………. 70

UK/Plessey ………………………………………….. 72

Telepen ………………………………………………. 74

Standard 2 of 5 ……………………………………… 76

RSS-14 ………………………………………………. 78

RSS-Limited…………………………………..…… 80

RSS-Expanded…………………………………..….. 82

China Post …………………………………………… 84

Italian pharmacode ………………………………… 86

Code 16K …………………………………..………… 88

PDF-417 ……………………………………………… 89

Micro-PDF…………………………………..……….. 91

EAN UCC Composite……………………………….. 93

String Format…………………………………………… 95

String Setting ………………………………………… 95

Transmission ………………………………………… 98

Appendix………………………………………………… 102

Test Chart ……………………………………………. 102

ASCII Code Table …………………………………… 105

Parameter setting List ……………………………….

106

Introduction

Installation- Keyboard Wedge

1) First of all, you must switch off power for the

terminal/computer.

2) Disconnect the keyboard cable from the back of the

terminal/computer.

3) Connect the appropriate interface cable to the

scanner and to the terminal/computer.

4) Turn the terminal/computer power on.

RS-232

1) Disconnect power to the terminal/computer.

2) Connect the appropriate interface cable and external

power supply (DC adapter) to the scanner.

3) Plug the serial connector into the serial port on the

back of your computer/terminal. Tighten the two

screws to secure the connector to the port.

4) Plug the power pack into power source.

5) Once the scanner has been fully connected, turn the

terminal/computer power back on.

USB (Simulate with keyboard wedge)

1) Connect the USB cable between scanner and PC.

2) Windows will automatically detect the USB device.

Note:

If any of the above operation is incorrect, turn off the

power immediately and checking any improper

connections. Go through all above steps again.

Default setting

For each barcode shown as below:

Read

Enable

Code Type

8110

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

UPC-A V V VA

UPC-E V V VE

EAN-13 V V VF

EAN-8 V V VFF

Code-39 V ＊

Interleaved

2 of 5 V i

Industrial

2 of 5 - - i

Matrix 2 of 5 B

Codabar V %

Code-128 V V #

Code-93 V two digits &

Code-11 VOne digit O

MSI/Plessey V @

UK/Plessey V @

Te l ep e n S

Standard 2 of

5 - - i

RSS-14 - R4

RSS-Limited - RL

RSS-Expande

d - RX

China Post t

Italian

Pharmacode. p

Code-16K -

PDF417 -

Micro-PDF - U

EAN UCC

Composite - RC

Read

Enable

Code Type

8150

8310

8250

8312

Checksum

Verificatio

Enable

Checksum

Transmission

Enable

Code

UPC-A V V V VA

UPC-E V V V VE

EAN-13 V V V VF

EAN-8 V V V VFF

Code-39 V V ＊

Interleaved

2 of 5 V V i

Industrial

2 of 5 - - i

Matrix 2 of 5 B

Codabar %

Code-128 V V V #

Code-93 V two digits &

Code-11 VOne digit O

MSI/Plessey V @

UK/Plessey V @

Te l ep e n S

Standard 2 of 5 V Vi

RSS-14 - R4

RSS-Limited - RL

RSS-Expanded - RX

China Post t

Italian

Pharmacode. p

Code-16K - - -

PDF417 - V - -

Micro-PDF - V8312 - - U

EAN UCC

Composite - - - RC

Inhaltsverzeichnis

Andere Meteor Barcode-Lesegerät Handbücher

Meteor

Meteor MiniCode Bedienungsanleitung

Meteor

Meteor Lion ZigBee Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

Atid

Atid AT188N Plus Bedienungsanleitung