Metra Electronics Nissan Pathfinder 2013-up Bedienungsanleitung
Wiring Harness: • Included with kit Antenna Adapter: • 40-NI12
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 99-7627HG
• ISO DIN radio provision with pocket
•ISO DDIN radio provision
•Painted to match factory components
• A) Radio trim panel with climate controls • B) Radio brackets • (C) Keypad assembly • D) Pocket
• E) (4) #8 x 3/8” Phillips screws • F) (2) White panel clips • Axxess interface and harness (not shown)
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
• Panel removal tool • Phillips screwdriver
• T-20 Torx driver
TOOLS REQUIRED
Nissan Pathfinder 2013-up
(with color screen)
99-7627HG
ADC E
F
B
99-7627HG
Dash Disassembly
1. Unclip and remove the trim panel
located between the vehicle screen
and control panel, and then remove
(1) Phillips screw now exposed.
(Figure A)
2. Unclip the screen control panel,
unplug the connectors, and then
remove the keypad assembly from
the panel. Note: The panel will be
reused during kit assembly.
(Figure B)
3. Unscrew (4) Phillips screws securing
the metal brace now exposed above
the radio/climate-control panel, and
then remove the brace. (Figure C)
4. Remove (2) Phillips screws from the
top of the radio/climate-control panel.
(Figure D)
5. Unclip and remove the trim panel
underneath the radio/climate-control
panel. (Figure E)
(Figure A) (Figure E)
(Figure D)
(Figure B)
(Figure C)
99-7627HG
6. Unclip and remove the radio/climate
control panel. (Figure F).
7. Remove (2) Phillips screws exposed
below the radio chassis, unplug the
connectors, then remove the radio
chassis. (Figure G)
8. Remove the climate control module
located under the radio chassis and
set aside for kit assembly.
(Figure G)
Continue to kit preparation.
Kit PreparationDash Disassembly
Kit Preparation
1. Secure the provided keypad
assembly into the screen control
panel removed in step 2 of dash
disassembly using the factory
screws. (Figure A)
2. Attach the supplied (2) white panel
clips to the radio trim panel with
climate controls. (Figure B)
Continue to kit assembly.
(Figure F) (Figure A)
(Figure G) (Figure B)
Climate
control
module
99-7627HG
Kit Assembly
ISO DIN radio provision with pocket
1. Secure the radio brackets to the
pocket using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Remove the metal DIN sleeve
and trim ring from the
aftermarket radio.
3. Slide the radio into the pocket/
bracket assembly using the screws
supplied with the radio. (Figure A)
4. Mount the climate control module
to the bracket assembly below
the radio and pocket, using
the hardware removed during
disassembly. (Figure B)
Continue to Axxess Interface
Installation
ISO DDIN radio provision
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
2. Mount the climate control module
to the bracket assembly below the
radio, using the hardware removed
during disassembly.
(Figure B)
Continue to Axxess Interface
Installation
(Figure A)
(Figure B)
(Figure A)
(Figure B)
99-7627HG
Axxess Interface Installation
• Retains factory screen
• Retains factory back up camera
• Retains factory AUX-IN
• Retains personalization features
• Ability to add aftermarket backup camera or additional video input
• Works in amplified or non-amplified models
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
FEATURES
• Cutting tool • Crimping tool • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
• Axxess Interface
• 7627 harness
• 16, 20, and 32-pin to 12 and 22-pin harness
• 14-pin to 4, 16, and 18-pin extension harness
• 14-pin to 14-pin extension harness wrapped in black tape
• 12-pin harness with (4) RCA jacks
• 20-pin to 24-pin extension harness wrapped in black tape
INTERFACE COMPONENTS
Connections to be made
From the 7627 harness to the aftermarket radio:
•Connect the Black wire to the ground wire.
•Connect the Yellow wire to the battery wire.
•Connect the Red wire to the accessory wire.
•Connect the Orange wire to the illumination wire. (If the aftermarket radio has
no illumination wire, tape off the Orange wire).
•Tape off and disregard the White/Blue wire, it will not be used in this application.
The following (2) wires are for an aftermarket multimedia/navigation radio
that provide these wires (if not required, tape them off and disregard them):
•Connect the Blue/Pink wire to the speed sense wire (if applicable).
•Connect the Green/Purple wire with a female bullet connector to the reverse
wire (if applicable).
•Connect the Green/Purple wire with a male bullet connector, to the
Green/Purple wire with a female bullet connector. Only connect this wire if the
Green/Purple wire with a male bullet connector has a wire populated on the
factory side.
99-7627HG
Connections to be made
•If you wish to add an aftermarket backup camera or external video source,
connect the Yellow RCA jack labeled “Backcam” into the desired source.
•12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (not included) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard
this harness. If it will be used, please refer to the ASWC-1 instructions for radio
connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
Note: Disregard the RCA jack labeled “FROM DVD”,
it will not be used in this application.
From the 12-pin harness with (4) jacks to the aftermarket radio
(for BOSE sound-systems only):
•Connect the Blue/White wire to the amp turn on wire (this wire must be
connected to hear sound from the factory amplifier).
•Connect the White, Gray, Green, and Purple RCA jacks to the audio outputs.
White is left front, Gray is right front, Green is left rear, and Purple is right rear.
For models without a BOSE sound-system:
•Connect the White wire to the left front positive speaker output.
•Connect the White/Black wire to the left front negative speaker output.
•Connect the Gray wire to the right front positive speaker output.
•Connect the Gray/Black wire to the right front negative speaker output.
•Connect the Green wire to the left rear positive speaker output.
•Connect the Green/Black wire to the left rear negative speaker output.
•Connect the Purple wire to the right rear positive speaker output.
•Connect the Purple/Black wire to the right rear negative speaker output.
For models with a BOSE sound-system:
•Tape off and disregard the White, White/Black, Gray, Gray/Black, Green,
Green/Black, Purple, Purple/Black wires, they will not be used in this
application.
•If you wish to retain the factory AUX-IN jack, connect the Red and White RCA
jacks labeled “AUX input”, to the AUX-IN jack (if applicable).
•Tape off and disregard the Red and White RCA jacks labeled “FROM DVD”, they
will not be used in this application.
•Tape off and disregard the Yellow RCA jack labeled FROM DVD, it will not be
used in this application.
99-7627HG
Installing the 99-7627 Final Assembly
Concerning the radio trim panel with climate controls and the keypad assembly.
The radio trim panel with climate controls has (2) connectors:
•Connect one end of the 14-pin to 14-pin extension harness wrapped in cloth tape,
to the connector on the left side (driver’s side of the vehicle as you are looking at
the front of the panel). The other end will connect to the Axxess interface.
•Connect the 14-pin connector of the 14-pin to 4, 16, and 18-pin extension
harness, to the connector on the right side (passenger side of the vehicle as you
are looking at the front of the panel). The 18-pin connector will connect to the
keypad assembly. The 4 and 16-pin harness will connect to the (2) harnesses
previously removed from the radio/climate-control panel removed in
dash disassembly.
•Connect the 20-pin connector of the 20-pin to 24-pin extension harness wrapped
in black tape, to the 20- pin harness removed from the factory radio/climate-
control panel. The 24-pin connector will then connect into the Axxess interface.
•Connect the 22-pin harness of the 7627 harness into the Axxess interface.
•With the key in the off position, connect the 16, 20, and 32-pin harness of the
7627 harness into the vehicle.
Attention: The 16-pin harness must be connected for the factory back-up
camera to function. There are (2) 16-pin connectors available in the dash.
Use the 16-pin connector that is grouped with the factory radio connectors;
the one removed from the radio chassis in step 7 of dash disassembly.
1. Locate the factory antenna connector in the dash, and complete all necessary
connections to the radio and climate control module. Metra recommends
using the proper mating adapter from Metra. Re-connect the negative battery
terminal, then test the radio and 99-7627 for proper operation.
Note: If using the ASWC-1 (sold separately), connect it after you test the 99-
7627B, with the key in the off position.
2. Mount the completed assembly into the dash using the 99-7627 radio trim
panel with climate controls, and then reassemble the dash in reverse order
of disassembly.
99-7627HG
•
The included interface is designed to auto-detect what vehicle it is in. In the
settings menu, there is an option of forcing the vehicle type to the interface.
• Go to - SETTINGS>MISCELLANEOUS>SELECT VEHICLE
Vehicle selection:
Screen Operation
All button functions are retained and are controlled in the same
manner that the factory buttons were controlled.
(example: Tire Pressure, Fuel Economy, Brightness, Clock Setting, etc).
Settings:
99-7627HG
Screen Operation
Note:
1. The aftermarket camera will be activated by the vehicle’s reverse
signal, which is sent to the Axxess interface.
2. The camera input can also be used as an AUX video in. The blank button
on the far right of the radio trim panel with HVAC controls will toggle the
AUX video on or off.
Note: The AUX video will only work with the vehicle in PARK.
• Reverse Camera Lines
• Go to – SETTINGS>MISCELLANEOUS> REVERSE CAM LINES
• On or off.
Note: By default, the back-up lines for the camera are set to off.
Continued on back cover
Backup camera/AUX video settings:
• Camera Input
• Go to – SETTINGS> MISCELLANEOUS>CAMERA INPUT>
AFTERMARKET CAMERA
• The factory equipped back-up camera will continue to function
without any additional wiring or programming.
The interface is shipped in this mode.
• If the vehicle does not come equipped with a factory backup camera,
an aftermarket camera can be used. If an aftermarket camera is
installed, the settings will need to be changed to reflect this.
99-7627HG
Screen Operation Updating the 99-7627
• Download and install the WebXXpress software update from
axxessinterfaces.com.
• Connect the USB-MINI-CAB update cable (sold separately) between the
99-7627 and the computer. The cable will connect into the port on the rear of
the kit labeled “A”.
Note: The 99-7627 will need to be powered up to be updated.
• From the Start Menu of the computer, click on “USB Bootloader”, and then click
“Update Board”. The software will begin to download at this point.
Note: If 30 seconds elapses before you finish this step, you will need to
remove power from the 99-7627, then reapply power, and then start the
update process again.
Note: Please note which firmware downloaded to the interface. This will
help in troubleshooting, if need be.
• To access the current software of this product after it has been installed.
• Go to - SETTINGS>MISCELLANEOUS>SYSTEM INFORMATION
•
Please have this information available when calling tech support for assistance.
System INFO:
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Metra Electronics Autoempfänger Handbücher
Metra Electronics
Metra Electronics AT-807HD Bedienungsanleitung
Metra Electronics
Metra Electronics 99-9013HG Bedienungsanleitung
Metra Electronics
Metra Electronics 99-3044 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7809B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5722 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7812B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7888 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-3528 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8219 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7382HG Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8907HG Bedienungsanleitung
Metra Electronics
Metra Electronics Ford F-150 2009-up Bedienungsanleitung
Metra Electronics
Metra Electronics 99-2003 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7519B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5025 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8209 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7397B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-9605B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-6537B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-3311B Bedienungsanleitung
