MetriCorr Slimline ICL-C Bedienungsanleitung

Toerringvej 7 Roedovre 2610 Denmark - Tel. +45 9244 8080 info@metricorr.com

Slimline series

ICL-C & MasterLink

Operation Manual

Document: 102272-00

Release date: June 2021

 MetriCorr 
 
 Slimline series –ICL-C & MasterLink Operation Manual 2 | 54 
Contents 
 
1Scope................................................................................................................ 4 
2ICL-C & MasterLink Unit.................................................................................... 5 
1 MasterLink module connectors & control ............................................................................6 
2 ICL-C module connectors ......................................................................................................7 
3Configuration ................................................................................................... 8 
1 Switch on & Initial Communication.......................................................................................8 
2 WebService - general ............................................................................................................9 
2.1 Setup of ICL-C & MasterLink........................................................................................................ 11 
2.2 Communication interval.............................................................................................................. 13 
2.3 Sample interval & Start time ....................................................................................................... 14 
2.4 Intensive measurements ............................................................................................................. 15 
2.5 Assigning probes/sensors/components to the ICL-C .................................................................. 16 
2.6 Linking ER probes to your account.............................................................................................. 17 
4Line Current Sensor ........................................................................................ 18 
1 LC input voltage range.........................................................................................................18 
2 Connections to steel pipe or other structure......................................................................19 
3 DC resistance (LC input) ......................................................................................................19 
4 AC measurements for a steel pipe (LC input) .....................................................................20 
5 WebService - Line Current Sensor (LCS)..............................................................................21 
5.1 Create Line Current Sensor.......................................................................................................... 21 
5.2 Defined Specific Resistivity Table ................................................................................................ 24 
5.3 Data display –Line Current Sensor (LC Sensor)........................................................................... 25 
5Installation ..................................................................................................... 28 
1 Solar Junction Box Installation ............................................................................................28 
2 Big Fink Installation .............................................................................................................33 
3 Big Fink Solar Solution.........................................................................................................38 
4 Battery Hat Solution............................................................................................................39 
6Your Data –Simple WEBservice Instructions................................................... 40 
1 View & Download Logged Data...........................................................................................40 

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 3 | 54

6.2 Unit Pipeline & Location Assignment..................................................................................41

6.3 Alerts ...................................................................................................................................42

6.4 Reports ................................................................................................................................43

7Satellite –communication .............................................................................. 44

7.1 Satellite modem & placement ............................................................................................45

7.2 Power & LED indicators.......................................................................................................45

7.3 Webservice Subscription.....................................................................................................46

7.4 Setup in Webservice............................................................................................................47

7.4.1 Example: 25h interval measurement campaign.......................................................................... 48

7.4.2 Example: 24h interval measurement campaign.......................................................................... 49

7.5 App & Data for satellite connected MasterLinks ................................................................49

Appendix 1: Junction Box Mounting Guide........................................................... 50

Appendix 2: Solar Charger Instructions ................................................................ 51

Revision

Date

Comments

Prepared

Review

Approval

001

2021-06-02

Review Section 7. Satellite –communication

RCH

LBT

Draft R001

2021-01-08

Operation Guide ICL-C & MasterLink.

Already reviewed by LBT and FGa.

This version is based on the previous ICL &

MasterLink operation guide by FrB, 2018-11-14.

RCH

LBT

FGa

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 4 | 54

1Scope

This document is a guideline for setup and operation of the datalogger model “ICL-C & MasterLink”from

MetriCorr’s Slimline series of remote monitoring equipment. Hereafter referred to as “unit”.

The MetriCorr remote monitoring system uses an online WebService, where all the data from site are

uploaded and stored. The unit consists of a MasterLink module and an ICL-C module, where both modules

are configured and controlled from WebService.

Before you start:

•If you want to link your new unit to an existing MetriCorr WebService account, please email

[email protected] with the following information:

-Account Name (existing or new) you wish the unit(s) to be assigned to.

-User email address (for new users to log in to existing or new accounts)

-MasterLink Serial Number(s) you wish to link to the account

•If you are a new customer or setting up a NEW account, please also provide details of a Primary

contact person for data & administration communication with MetriCorr.

1. Name & title / position

2. Email address

3. Telephone number

Once you have confirmation that the units have been assigned to the account as requested (together with

IMPORTANT: Do not disassemble the unit. If the unit is malfunctioning, please contact MetriCorr.

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 5 | 54

2ICL-C & MasterLink Unit

The Slimline ICL-C

measurement module

is paired with a

MasterLink control and

communications

module. They are

shipped preassembled

as shown:

Figure 1. ICL-C & MasterLink as shipped

Standard accessories:

-Antenna LTE with 1m wire and adhesive pad

-Protective caps for connectors

-Power cable with DC connector

-Yellow wire 1m, 4mm banana connectors

-Black wire 1m, 4mm banana connectors

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 6 | 54

2.1 MasterLink module connectors & control

The MasterLink module comes with a Status/control button, antenna, and Power supply connectors as

standard. Optional interface connectors are available on-demand.

Figure 2. MasterLink module connectors & control

Table 1. MasterLink - Specifications

MasterLink –Specifications

Battery Lifetime

+3 years @ 1h logging intervals and

weekly transmissions

Casing

IP65

Humidity

0-100% RH condensing conditions

Operating conditions

-40 °C to +85 °C

Storage capacity

+200 000 readings

Logging intervals

(Normal mode)

10 min → ∞, recommended 1 hour

Logging interval

(Campaign mode)

1 sec in pre-defined time intervals

A: Antenna connection

B: Status/control button & LED indicator

C: Power supply connector

(with protective cap)

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 7 | 54

2.2 ICL-C module connectors

The ICL-C module's endplate consists of five connectors for the ER probe connection, Line Current Sensor,

and Reference electrode to Pipe/structure measurement.

ER channel (1)

Resistance Range

150 mΩ

Repeatability

0.2 µΩ

Precision

0.4 µΩ

Line Current channel (2)

Input voltage range DC

(Before clip)

± 1.2 V

Input voltage range AC

(Before clip)

845 mVRMS

Target input range for

DC measurements

-20 mV →+20 mV

Resolution

0.2 µV

DC accuracy

± 1 µV

AC accuracy

± 4 µV

Input resistance

33 kΩ

Terminal "Pipe" –Pipe/structure connection

Terminal "Ref." –Reference Electrode connection

The voltage measurement between

"Pipe" and "Ref." is performed by both

channel 1 and channel 2.

Voltage measurement (both channels)

Input range (voltage)

± 100 V

Resolution (voltage)

1 mV

DC accuracy (voltage)

± 1 mV ± 0.3% reading

AC accuracy (voltage)

± 2 mV ± 1% reading

ER Probe Current measurement (channel 1)

Current range

± 300 mA

Resolution (current)

0.1 µA

AC accuracy (current)

± 4 µA ± 1% reading

DC accuracy (current)

± 1 µA ± 1% reading

Figure 3. ICL-C module

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 8 | 54

3Configuration

3.1 Switch on & Initial Communication

Once connected to the antenna and battery, push the 'Status/Control' button ('E' in Figure 3) and release

(<0.5s). This will indicate the unit's current status/mode with a series of flashes on the LED built into the

button. Please refer to the LED flash patterns below.

*The device is Off. 5 short (0.5 milliseconds) flashes per second for 5

seconds. This signal is triggered by a short (<0.5s) push on the push-

button.

Figure 4. LED flash indication

Mode / status

Description

Waiting

The device is active and waiting for the next measurement to be performed.

Short (50 milliseconds) flash every 8 seconds

Measuring

The device is performing a measurement.

Longer flash (0.5 seconds) repeated every second.

Searching

The device is searching for a network.

1 short (0.5 milliseconds) flash repeated every second.

Transmitting

The device is transmitting data to the WebService.

3 short (0.5 milliseconds) consecutive flashes repeated every second.

Off

The device is Off.

5 short (0.5 milliseconds) flashes per second for 5 seconds.

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 9 | 54

3.2 WebService - general

Log on to https://data-metricorr.com using the username and password sent to you as per Section 1. For

data safety, it is recommended that your assigned password should be changed on your first login. This can

be done in the 'Profile' menu. You should also 'Logout' when you have completed your session.

The landing page is the "ICL ER probe" page and looks like this:

Click "DATA" -> "I LCS" to show the "Line Current Section":

Click "RMU" -> "MASTERLINKS" to show the page "Your defined MasterLinks":

MetriCorr

Slimline series –ICL-C & MasterLink Operation Manual 10 | 54

Figure 5." Your defined Masterlinks" page

"Your Defined MasterLinks" can be any

of the following types: ICL, VL100 or ICL_C

An overview of the columns in the" Your defined Masterlink" table above is described in Table 2 below:

Table 2. Your defined MasterLinks –parameter description

Parameter

Data (example)

Comment

MobileID

AL02840252

MasterLink Serial number

SW version

1.3.145,1.3.145,1.3.145

Software version (MasterLink, Bluetooth, ICL-C module)

Battery

Not fitted with battery

Net info

3G/Fair,-81dBm

Network connection and signal strength

Received Time (UTC)

13-Jan-2021 11:51:21

UTC time stamp of LAST communication/data transfer

Next wakeup (UTC)

13-Jan-2021 12:50:32

UTC time stamp of NEXT communication attempt

Status

OK, 348 logger lines

received

" OK" indicates that communication went well.

" 348 logger lines received" inform amount of data received since

last communication session.

Longitude

12.430468

Geographic coordinate [degrees]

Lattitude

55.695079

Geographic coordinate [degrees]

Time

11:38:57

UTC time stamp for geographic coordinate

Connected Device

ICL-C

Indicate type of logger, in example: ICL, VL-100 or ICL-C

Serial number

AT0239770

Serial number of ICL-C module

Channel 1 SN

PI20304415

Serial number of connected ER probe

Channel 2 SN

Pipesection 08

Serial number of Line Current Component, i.e. a pipe section.

Options

Setup

Link to the Setup page

History

Link to the History page

S/N (ICL_C module)

Line Current (component)

ER probe (component)

Setup link

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MetriCorr Datenlogger Handbücher

MetriCorr

MetriCorr Slimline VL100 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung