MFJ MFJ-1622 Bedienungsanleitung

MFJ-1622 Instruction Manual Window Mount Antenna

MFJ-1622 Window Mount Antenna

Introduction

The MFJ-1622 Antenna was designed to provide portable or permanent HF communications on

40 through 10 meters and VHF on 6 and 2 meters. The universal mount design allows the user to

install the antenna in many ways. The mount will easily attach to window frames, balconies, and

railings. The MFJ-1622 works well indoors mounted to a desk or table as well.

The antenna consists of a collapsible whip, loading coil assembly, universal mount, counterpoise

wire, and choke. The operating frequency is adjusted by moving the tap on the coil. The

counterpoise wire length is adjusted for minimum SWR. The MFJ-1622 Antenna will allow the

operator to get on the air from locations where antenna size is limited.

Choosing a Mounting Position

WARNING: ALWAYS ATTACH THE SAFETY ROPE TO A STABLE SUPPORT

BEFORE ATTEMPTING TO ATTACH THE UNIVERSAL MOUNT TO A

WINDOW FRAME OR RAIL. INJURY AND DAMAGE COULD OCCUR

IF THE ANTENNA WERE TO FALL.

The design of the antenna allows it to be installed in many ways. It can be easily attached to a

window frame, window box or balcony railing. A Wooden fence is another common mounting

location.

The best performance will be obtained by placing the antenna outside, however the antenna may

be used indoors if necessary. The base plate may be attached to a table, book shelf, or other

suitable support. The counterpoise is simply placed on the floor. Some installations may require

the use of a C-clamp or vice-grips to secure the base plate. Always remember to keep the

antenna away from metal objects and out of reach to prevent injury.

WARNING: SERIOUS RF BURNS AND INJURY CAN OCCUR IF CONTACT IS

MADE WITH THE ANTENNA.

Parts List

[ ] Antenna Whip

[ ] Loading Coil Assembly

[ ] 50 feet of RG58 Coax

[ ] 35 feet of counterpoise wire

Tools Needed

[ ] #1 Flat Head Screwdriver

[ ] #2 Flat Head Screwdriver

[ ] Measuring Tape

[ ] 12mm or equivalent wrench

[ ] Mounting Bracket/Base Plate

[ ] Spacer

[ ] 2 feet of Safety Rope

[ ] _” x 3 _” bolts

[ ] _” – 24 split lock washer

MFJ-1622 Instruction Manual Window Mount Antenna

[ ] 3 Plastic wire ties

MFJ-1622 Instruction Manual Window Mount Antenna

Assembly

[ ] 1. Remove all Parts from the packing material. Check to see that all are present using the list

on page 1.

[ ] 2. Place the _”- 24 split lock washer onto the threaded end of the whip.

[ ] 3. Screw the antenna into the coupling nut (shown in Figure 1) located on top of the coil

assembly.

[ ] 4. Secure the antenna into the coupling nut using a 12mm wrench.

[ ] 5. Uncoil the coax cable to its full length.

[ ] 6. Measure 30 feet from the antenna end of the coax and mark this point with a piece of

tape.

[ ] 7. Begin 18 inches from the antenna winding the coax in a circle, 8-10 inches in diameter,

using the 30 feet measured in the previous step.

[ ] 8. Use the three black wire ties supplied to tie the choke coils together. Space the ties out

evenly around the circle. Figure 1 shows a picture of the finished choke.

[ ] 9. Insert the _” x 3 _” bolts into the threaded holes on the base plate approximately one

inch as shown in Figure 1.

[ ] 10. Place the spacer plate onto the bolts as indicated in Figure 1.

[ ] 11. Push one end of the safety rope through the rope hole as indicated in Figure 1. Tie a knot

on both ends of the rope to secure it.

ANTENNA

COUPLING

NUT

CHOKE

TAP

LOADING COIL

SAFETY ROPE

SPACER

SCREWS

WING NUT

Figure 1

MFJ-1622 Instruction Manual Window Mount Antenna

Installation

IMPORTANT: WHILE INSTALLING THE ANTENNA TO A WINDOW OR

BALCONY CONNECT THE SAFETY ROPE OF THE BASE PLATE

TO A SUPPORT.

[ ] 1. Choose a location to mount the antenna.

WARNING: NEVER MOUNT THE ANTENNA IN A LOCATION CLOSE TO POWER

LINES. SERIOUS INJURY OR DEATH MAY OCCUR.

[ ] 2. Connect the safety rope to a good support.

[ ] 3. Attach the mounting bracket in position by placing the bracket over or around the surface

of the support.

NOTE:THE ANTENNA SHOULD BE ORIENTED AWAY FROM WINDOWS AND

OTHER OBJECTS THAT ARE WITHIN CLOSE RANGE IF POSSIBLE.

[ ] 4. Tighten the screws on the rear of the base plate against the surface of the support. The

screws should be tightened in equal increments to keep the force on the spacer plate

proportioned.

[ ] 5. Decide which mount hole will be used on the mounting bracket according to your

situation. There are five holes available. Figure 1 indicates the possible hole positions.

[ ] 6. Extend the antenna whip to its full length

[ ] 7. Remove the wing nut and lock washer from the bottom of the coil assembly.

[ ] 8. Place the coil bolt through the mounting bracket hole.

[ ] 9. Secure the antenna to the mount by replacing the lock washer and wing nut on the bolt

and tightening them firmly.

[ ] 10. Loosen the wing nut and flat washers on the Counterpoise Attachment.

[ ] 11. Insert the end of the counterpoise wire which has the insulation removed between the two

flat washers.

[ ] 12. Tighten the wing nut to secure the counterpoise.

MFJ-1622 Instruction Manual Window Mount Antenna

Frequency and SWR Adjustment

The antenna is tuned to the operating frequency by adjusting the tap on the loading coil and the

length of the counterpoise wire. The excess counterpoise wire should be wrapped in a small coil

3-4 inches in diameter. The SWR is checked using a transmitter and SWR meter but will be

much easier using an analyzer such as the MFJ-259/269 SWR Analyzer. Initial tuning will

require some time. A permanent marker can be used to place marks on the coil to reduce the

amount of time required for future tuning.

Before tuning check the following:

qCoax Connections

qCounterpoise Connections and Length

qWhip Connection and Length

qThe tap is only touching one coil turn

[ ] 1. Begin by placing the tap on turn 0 (Figure 2) which will short the entire coil. The tap

should only be in contact with one coil at a time.

Figure 2

[ ] 2. The counterpoise wire should be less than 1/4 wavelength of the desired frequency

[ 468 / frequency (MHz) ]. This length may need to be increased or decreased according

to height above ground level.

[ ] 3. With the tap on turn 0 and the counterpoise just under 8 feet, the resonance point should

be approximately 30 MHz. If this is not true lower the tap on the coil to lower the

frequency or shorten the whip to raise the frequency. Table 1 gives approximate tap

points for each of the HF bands with the counterpoise at ground level.

MFJ-1622 Instruction Manual Window Mount Antenna

[ ] 4. Each installation may require different

lengths of counterpoise wire and tap

positions. The greatest factor in

determining the counterpoise length will

be the height above ground level. The

higher the installation, the closer the

counterpoise length will need to be to a _

wavelength = 468 / frequency (MHz).

[ ] 5. Operation on the 6 and 2 meter bands

requires that the top section of the whip be

retracted completely. This may vary with

some installations. The counterpoise

length should be less than 5 feet.

Technical Assistance

If you have any problem with this unit first check the appropriate section of this manual. If the

manual does not reference your problem or your problem is not solved by reading the manual,

you may call MFJ Technical Service at 662-323-0549 or the MFJ Factory at 662-323-5869.

You will be best helped if you have your unit, manual and all information on your station handy

so you can answer any questions the technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road,

Starkville, MS 39759; by Facsimile (FAX) to 662-323-6551; or by email to

[email protected]. Send a complete description of your problem, an explanation of

exactly how you are using your unit, and a complete description of your station.

Table 1

Counterpoise Length at Ground Level

MHz

Coil #

Counterpoise

Length (Ft)

144.0

5’

50.1

5’

28.00

1.75

7’ 9”

24.89

1.5

8’ 5”

21.00

5.5

10’ 6”

18.068

11’

14.00

18’

10.1

19’ 5”

7.00

33’

Inhaltsverzeichnis

Andere MFJ Antenne Handbücher

MFJ

MFJ MFJ-1432 Bedienungsanleitung

MFJ

MFJ MFJ-1775W Bedienungsanleitung

MFJ

MFJ 1801 Bedienungsanleitung

MFJ

MFJ 1798 Bedienungsanleitung

MFJ

MFJ 1731 Bedienungsanleitung

MFJ

MFJ 1777 Bedienungsanleitung

MFJ

MFJ IntelliTuner -991 Bedienungsanleitung

MFJ

MFJ MFJ-1770 Bedienungsanleitung

MFJ

MFJ MFJ-1890 Bedienungsanleitung

MFJ

MFJ MFJ-1796 Bedienungsanleitung

MFJ

MFJ MFJ-949E Versa Tuner II Bedienungsanleitung

MFJ

MFJ MFJ-1912 Bedienungsanleitung

MFJ

MFJ MFJ-1796 Bedienungsanleitung

MFJ

MFJ MFJ-1438 Bedienungsanleitung

MFJ

MFJ MFJ-1024 Bedienungsanleitung

MFJ

MFJ MFJ-1778M G5RV JR. Bedienungsanleitung

MFJ

MFJ MFJ-1786 Bedienungsanleitung

MFJ

MFJ 1436 Bedienungsanleitung

MFJ

MFJ MFJ-1835H Bedienungsanleitung

MFJ

MFJ MFJ-1754 Bedienungsanleitung

MFJ

MFJ MFJ-1775 Bedienungsanleitung

MFJ

MFJ MFJ-918WM Bedienungsanleitung

MFJ

MFJ 2286 Bedienungsanleitung

MFJ

MFJ MFJ-1795W Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung