MG KS2 Bedienungsanleitung

BEFORE USE ....

Thank you for choosing us. Before use, please check con-

tents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact our sales ofﬁce or representatives.

■PACKAGE INCLUDES:

DC alarm (body + base socket + input resistor) ................(1)

Input resistor is provided only with current input type.

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• This equipment is suitable for Pollution Degree 2, Meas-

urement Category II (output, transient voltage 2500V)

and Installation Category II (transient voltage 2500V).

Reinforced insulation (signal input or output to power in-

put: 300V) and basic insulation (signal input to output:

300V) are maintained. Prior to installation, check that

the insulation class of this unit satisﬁes the system re-

quirements.

• Altitude up to 2000 meters.

• The equipment must be mounted inside a panel.

• The equipment must be installed such that appropriate

clearance and creepage distances are maintained to con-

form to CE requirements. Failure to observe these re-

quirements may invalidate the CE conformance.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

AC power: Rating ±10%, 50/60 ±2 Hz, approx. 2VA

DC power: Rating ±10%, approx. 2W

■GENERAL PRECAUTIONS

• Before you remove the unit from its base socket or mount

it, turn off the power supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body Base Socket

0–100%

(0–10VDC)

SET MONITOR

SET HI

COM

Specifications

Input Resistor

■FRONT PANEL CONFIGURATION

Lo LED

Hi LED

Lo Adj.

Hi Adj.

Hi Setpoint Monitor

Lo Setpoint Monitor

COM.

• Explanations

Hi and Lo Adjustments are used to set the alarm setpoints.

A 0 – 10V DC is output at the Hi and Lo setpoint monitor

jacks across the COM jack, proportional to the setpoint 0 –

100%.

The Hi and Lo LEDs turn on when the coil for each relay is

energized.

• Examples

For setting the relay to trip above 80% of the full-scale in-

put signal, turn the Hi Adj. until you read 8.0V at the Hi

Setpoint Monitor.

DC ALARM

(CE) MODEL KS2

EM-3612 Rev.3 P. 1 / 3

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

INSTRUCTION MANUAL

INSTALLATION

Detach the yellow clamps located at the top and bottom of

the unit for separate the body from the base socket.

Clamp

(top & bottom)

DIN Rail

35mm wide

Spring Loaded

DIN Rail Adaptor

Shape and size of the base socket

are slightly different with various

socket types.

■DIN RAIL MOUNTING

Set the base socket so that its

DIN rail adaptor is at the bot-

tom. Hang the upper hook at

the rear side of base socket on

the DIN rail and push in the

lower. When removing the

socket, push down the DIN

rail adaptor utilizing a minus

screwdriver and pull.

■WALL MOUNTING

Refer to “EXTERNAL DI-

MENSIONS.”

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the front of the unit.

When an input resistor is provided with the module, attach it together with input wiring to the input screw terminals.

■EXTERNAL DIMENSIONS unit: mm (inch)

80 (3.15)

50 (1.97)

72 (2.83) [3.3 (.13)]

80 (3.15)

(.79)

60 (2.36)

72 (2.83)

7.8 (.31)

CLAMP

(top & bottom)

DIN RAIL

35mm wide

–

4.5 (.18) dia.

MTG HOLE

25 (.98) deep

–

M3.5

SCREW

• When mounting, no extra space is needed between units.

1015

103 (4.06)

132 (5.20)

■CONNECTION DIAGRAM

–

INPUT

V(–)

POWER

*Input shunt resistor attached for current input.

U(+)

N.C.

OUTPUT

N.O.

COM

N.C.

OUTPUT

N.O.

COM

■TERMINAL ASSIGNMENTS unit: mm (inch)

Input shunt resistor attached

for current input.

1015

INPUT RESISTOR

(model: REM)

12 (.47)

KS2

EM-3612 Rev.3 P. 2 / 3

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

7 – 14 with a multimeter.

3) Input: Check that the input signal is within 0 – 100% of

the full scale.

4) Alarm operations: Check the alarm operations referring

to the ﬁgure below.

5) Output load: Check that the output load is 380V

AC/120VA or 125V DC/30W at the maximum (≤ 0.5A).

For maximum relay life with inductive load, external pro-

tection is recommended.

Alarm Trip Operation Terminal No. in parentheses

Trip Operation in Power Failure

: Terminals 1 – 2, 9 – 10 turn ON.

050 100

Input

(%)

Lo Setpoint Hi Setpoint

Hi Output

(9–15)ON

Lo Output

(1–2)ON

(1–11)ON

(9–10)ON

SETPOINT ADJUSTMENT

Adjustment procedure for the Hi and Lo setpoints are as

follows:

■HOW TO ADJUST ALARM SETPOINTS

The monitor jacks output 0 – 10V DC in proportion to the

0 – 100% setpoints.

• Hi Setpoint

Measure the voltage at the Hi setpoint monitor jacks and

turn the Hi Adj. until you read a desired value.

• Lo Setpoint

Measure the voltage at the Lo setpoint monitor jacks and

turn the Hi Adj. until you read a desired value.

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes.

• Hi Setpoint

Increase the input signal from a value lower than the set-

point and check that the relay trips at the Hi setpoint

(Measure the voltage at the Hi setpoint monitor jacks).

• Lo Setpoint

Decrease the input signal from a value higher than the

setpoint and check that the relay trips at the Lo setpoint

(Measure the voltage at the Lo setpoint monitor jacks).

When the trip points are shifted, recalibrate the unit accord-

ing to the “SETPOINT ADJUSTMENT” explained earlier.

When the monitor jacks outputs are shifted, please contact

our sales ofﬁce or representatives.

LIGHTNING SURGE PROTECTION

We offer a series of lightning surge protector for protec-

tion against induced lightning surges. Please contact us to

choose appropriate models.

KS2

EM-3612 Rev.3 P. 3 / 3

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Andere MG Sicherheitssystem Handbücher

MG Mini-M M2SED Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung