MGL Avionics A16 Betriebsanleitung

MGL Avionics

A16 Aviation Audio Panel

and Razor Intercom control head

User and Installation manual

Table of Contents

FCC Statement............................................................................................................................4

General........................................................................................................................................4

Document history........................................................................................................................4

Description..................................................................................................................................4

Audio grounds.........................................................................................................................6

Audio wiring from A16 to CO microphone input..................................................................7

Audio signal flow during transmit............................................................................................9

Dual circuit intercom...............................................................................................................9

PTT behavior...........................................................................................................................9

arker beacon receiver........................................................................................................10

Power supply........................................................................................................................10

Digital control interfaces.......................................................................................................10

Audio input specifications.....................................................................................................10

Audio output specifications...................................................................................................11

Audio filters............................................................................................................................11

Power supply.............................................................................................................................11

Power supply fusing and protection......................................................................................11

Environmental qualification matrix............................................................................................12

A16 Connector pinout, Power side...........................................................................................14

A16 Connector pinout, Audio side.............................................................................................15

Typical connection diagrams.....................................................................................................16

Noise canceling inputs – how they work...............................................................................18

Control heads and options........................................................................................................20

Pinout for 3.18” Razor Intercom control head......................................................................20

Razor A16 head........................................................................................................................21

Using the A16 intercom.............................................................................................................22

Setting the volume................................................................................................................23

Audio configuration options:.................................................................................................23

Audio signal level controls....................................................................................................23

Bluetooth connectivity...............................................................................................................24

Bluetooth pairing...................................................................................................................24

Setting up microphone inputs...................................................................................................26

Adjusting VOX: .....................................................................................................................27

Adjusting Input sensitivity:....................................................................................................27

Setup of audio sources.............................................................................................................27

Assigning names to inputs....................................................................................................29

The Intercom iscellaneous menu...........................................................................................31

Signal Check.............................................................................................................................32

The Head enu........................................................................................................................33

Edit phonelist........................................................................................................................33

Set Backlight.........................................................................................................................33

Inputs....................................................................................................................................33

About.....................................................................................................................................33

A1/A2....................................................................................................................................34

aking a phone call..................................................................................................................34

The phone list............................................................................................................................36

..................................................................................................................................................36

Editing the phone list.............................................................................................................37

Cockpit voice recorder (CVR)...................................................................................................38

Electrical state interfaces..........................................................................................................39

PTT inputs.............................................................................................................................39

Accept and Hangup inputs....................................................................................................39

RS232 and CAN bus communication protocols........................................................................39

Certifications..............................................................................................................................40

echanical dimensions........................................................................................................41

aterials ..............................................................................................................................41

Dealing with common audio signal issues................................................................................42

Images.......................................................................................................................................44

Self test facility..........................................................................................................................47

Razor Firmware updates...........................................................................................................49

CC Statement

THIS DEVICE CO PLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE AY NOT CAUSE HAR FUL

INTERFERENCE, AND (2) THIS DEVICE UST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT AY CAUSE UNDESIRED OPERATION.

FCC ID: A8TBM62S2

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR ODIFICATIONS

NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR CO PLIANCE. SUCH

ODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIP ENT.

General

This manual documents the installation and use of the A16 audio panel system. Please note

that operation of the audio panel is done via a connected control system such as an EFIS or

dedicated audio panel control panel or control head.

User interface varies by type of connected system. Please refer to documentation for the

connected equipment for details.

This manual describes available settings through the connected equipment in a generic way

that is applicable to all types.

Document history

8 November 2019, first release.

Description

The A16 audio panel is a split module consisting out of the audio panel system body and

optional external control. External control can take the form of one or more panel mount

control heads and/or control by an EFIS system.

The A16 audio panel provides the following functions:

a) Six independent microphone channels, each with own VOX and sensitivity settings to allow

mixed headsets. Channels can be grouped into Pilot and Passenger groups.

b) Support for two CO radios, each with audio input and output and individual PTT control.

Level control for all audio signals. Two independent Pilot and PAX PTT inputs provided. PTT

inputs dedicated to Pilot and PAX microphone circuits.

c) Support for two NAV radio audio inputs with individual level control.

d) Two independent auxiliary audio inputs with individual level control.

e) Wired stereo music input with level control – may be reassigned as two further AUX

channels.

f) Auxiliary audio output (Typical use for cockpit voice recorders etc).

e) Bluetooth mobile phone support to make and receive calls. Optional wired inputs for call

and hangup buttons.

f) Bluetooth stereo music streaming support.

g) Ability to connect to two Bluetooth devices simultaneously. Ability to automatically

reconnected to the last two connected Bluetooth devices on startup (This depends on the

Bluetooth device itself – it must allow a device initiated connection).

h) Dual circuit, stereo Pilot and PAX headset outputs.

I) Firmware updates via Bluetooth connection (requires PC or Laptop computer with Bluetooth

running Windows 7 or later).

J) Firmware update of connected Razor control head via A16 Firmware updates.

k) Communications/Control interfaces: Two RS232 ports, One CAN bus, Bluetooth SPP

profile support.

l) Built in cockpit voice recorder (CVR). This device records in an “endless tape” fashion all

microphone circuits as well as both CO radio inputs. It records about 35 minutes worth of

audio. It only records active audio, not any silence so silence periods do not use up recording

time. Recording may be played back as a block via all headset outputs or it can be extracted

in digital form via the RS232 port 1 using the supplied application from GL Avionics.

Audio grounds

In order to reduce the potential for unintended audio noise on audio wiring all audio input

circuits are based on differential grounding. This means audio inputs are not connected to the

A16 power supply grounds but are instead connected to their own audio inputs. This allows

the elimination of common mode noise as the A16 will only process differential signals.

For this purpose input grounds are grouped as follows:

1) All icrophones share a common ground.

2) All CO radios share a common audio ground

3) All NAV radios share a common audio ground

4) Wired music input has its own private ground

5) Both Auxiliary inputs each have their own private grounds.

All audio outputs are on a single shared ground but with multiple provided connections: On

the audio connector side two pins are available for audio output ground while on the power

connector a single audio output ground is provided for the auxiliary output.

In order to take full advantage of the differential input signal support both the signal wire and

the related ground wire must have the same noise profile in amplitude and time. In other

words, both connections have exactly the same unwanted signal. This is refereed to as the

common signal. The wanted signal is the difference between the signal and ground wires.

This is called the differential signal. The A16's audio inputs are designed to favor the

differential signal and reject the common signal.

It is recommended to route audio signals using shielded cables. The practice of using wire

shields as convenient ground connections is specifically discouraged. This creates ground

loops which are receivers for audio noise and makes it impossible to take advantage of the

A16's noise rejecting inputs.

The correct method to wire an audio input is to include the signal and ground as two

connections inside a shielded cable. The shield in turn connects to an independent ground.

This way the signal and signal ground will contain the same unwanted signal (noise) and this

can now be rejected by the A16.

There are various options as to what ground to use for the shields and it is not critical.

Suitable grounds are any of the A16's Audio output ground pins or a ground at the source of

the signal.

Never connect the audio cable shield at both ends of the connection. You must only connect it

on one end. This way it is not possible for any DC current or signal to flow via the shield.

Audio wiring from A16 to COM microphone input

This wired connection, in most cases will require special attention in order to prevent RF

related issues such as feedback during active TX.

A potential problem exists due to the required audio ground connection between A16 audio

panel and the CO radio. This may create a ground loop causing potentially significant

issues depending on the level of RF energy received by your aircraft's wiring during transmit.

This type of problem is typically worse on composite aircraft compared to metal skinned

aircraft.

In order to eliminate this problem the A16 provides several avenues of solutions. These are

listed here in order of preference and effectiveness:

1) Fit a 600 ohm line matching audio transformer between A16 and CO radio

microphone input. GL Avionics provides suitable high quality transformer modules.

The transformer should be fitted as close to the CO radio as possible (minimizing the

wiring length between transformer and CO radio). The transformer provides two

advantages: It completely eliminates the ground loop and provides a very effective RF

signal block (RF signals cannot pass through the transformer).

This solution is also recommended if your CO radio requires a DC load to detect a

connected microphone.

This connection is particularly recommended if your CO radio and A16 intercom are

not sharing the same power supply ground or the grounds between the two devices

are not electrically identical or contain A/C interfering signals that are not common to

both devices. Should either of these conditions exist it is recommended to use a

second transformer on the CO audio output to the A16 audio panel CO input. This

will prevent any ground potential related issues and provide the highest possible audio

quality under these conditions. Note that it may also require the use of a small low

power relay to activate the PTT on the CO radio – the relay may be driven by the A16

PTT output (please do not forget a reverse biased “snubber” diode in parallel to the

relay coil as otherwise the A16 may be damaged by the back-E F of the coil when it

deenergizes).

2) Use a two core shielded cable from A16 to CO radio and wire a 47ohm resistor

between CO radio microphone input and CO radio microphone input to ground.

The shield must be connected at the CO radio signal ground connection OR at the

A16 audio output ground connection (Never both). One of the internal shielded cores

shall be used to connect A16 audio ground to microphone ground of the CO radio

while the remaining shielded core will connect the A16 CO output to the microphone

input of the CO radio. The 47 ohm resistor should be connected at the CO radio.

Background: The 47 ohm resistor provides a very low impedance to interfering RF

signals, reducing the RF signal voltage at the microphone input. The A16 has a very

wide range output signal adjustment via a 1KOhm series output resistor. So it can

easily produce signals large enough to cater for the 20:1 loss in signal amplitude.

The 47 ohm resistor from microphone input to ground will also provide a DC path

which some radios require to detect a microphone.

3) The same as option 2 can be used if you have a CO radio that requires connection of

a dynamic microphone. In this case the resistor value should be dropped to 4.7ohm.

If your CO radio provides this (most do), reduce the microphone input sensitivity adjustment

to minimum. This also reduces the reaction of the CO radio to any interfering signals. The

A16 on the other hand provides a wide range of output signal amplitude adjustment. So the

idea is “make the CO radio as insensitive as possible” and then compensate by increasing

the output signal of the A16. This provides an easy method to increase the “signal to noise

ratio”.

If you are using a GL Avionics V16 CO radio, please use the Pilot IC input and Pilot PTT

input of the V16, leave the PAX inputs unconnected.

If you are using the supplied Bourns 5001 audio isolation transformer (recommended), the

settings are as follows: On the V16 set the Pilot IC Gain to 0.00db. On the A16 adjust the

CO output level to maximum (or near maximum). Select the CO input level to about 1/3

and the V16 RX and IC levels to about ½ of maximum.

For a direct, non isolated connection:

Using the V16 setup menu – please adjust both Pilot and PAX IC Gain to -12.00db (the

lowest setting). On the A16 – adjust the CO output level to about the 2/3 setting and the

CO input level to about 1/3. It is recommended to use the V16 VOX system at a fixed level

of “1” (do not use the bypass setting). You will be using the VOX functions of the A16 – so

leave the V16 at “1” which is just enough to switch the intercom in the V16 off when not it use.

It is advisable to wire a 100 ohm resistor (carbon type, not wound) between microphone input

and microphone ground on the V16 connector in order to lower the signal apparent

impedance and increase resistance to interference.

Audio signal flow during transmit

The A16 provides two selectable audio signal flows during active transmit. This is selected in

the Intercom setup menu of the A16 under “ iscellaneous”.

The “normal” option is: “CO sidetone from CO audio in”.

With this option selected audio flow is: icrophone → A16 → CO radio → A16 → headset.

The alternative is: “CO sidetone Intercom loop back”.

With this option selected you have two flows at the same time:

icrophone → A16 → CO radio

icrophone → A16 → Headset

Note that these settings are independent for CO 1 and CO 2 radios.

The first option will typically allow you to listen to your outgoing transmission and also help

identifying issues such as RF feedback (howling, hollow “bathroom” sound etc). The second

option can be used if your radio does not provide audio feedback during transmission.

Dual circuit intercom

The A16 provides two independent stereo output channels. These are refered as Pilot and

PAX circuit.

icrophone input ONE is always assigned to the Pilot circuit.

icrophone input TWO may be assigned to the Pilot or PAX circuit.

icrophones THREE to SIX are always assigned to the PAX circuit.

Each audio source may be assigned to either circuit or both. In addition most sources may be

assigned to either the left or right audio channel or both. For example: You may assign CO 1

to the left channel and CO 2 to the right channel if desired.

The two circuits may be operated independent or joined.

If joined, all microphone signals will be audible on both Pilot and PAX circuits. This means

Pilots and PAX may communicate with each other. All other sources however will remain at

their assignments. For example you may exclude music source from being audible on the

Pilot circuit and CO radios may not be audible on PAX circuits.

If separate, each circuit operates independent.

PTT behavior

The A16 provides two PTT inputs. PTT1 is dedicated to the Pilot circuit and PTT2 is dedicated

to the PAX circuit.

Two PTT outputs are available. PTT1 output 1 is dedicated to CO 1 and PTT2 output is

dedicated to CO 2.

It is possible to wire both PTT1 and PTT2 in parallel to a single PTT switch if this is desired.

If PPT1 is held active, only voice from the pilot circuit will be routed to the currently selected

CO radio for TX.

If PTT2 is held active, only voice from the PAX circuit will be routed to the currently selected

CO radio for TX.

If both PTT1 and PTT2 are held active then both pilot and PAX circuit will be routed to the

currently selected CO radio for TX.

Note: Only microphone signals will be routed to the CO radios. No other audio sources can

be routed to the CO radios. This includes including phone calls.

Only one CO radio can be selected for TX.

Marker beacon receiver

The A16 variant implements a 75 hz marker beacon receiver. The marker beacon antenna

is connected to pin 1 and 2 of the Power side DB25 connector. The marker beacon receiver

can be operated in a reduced sensitivity mode.

Power suppl

The A16 audio panel system is designed to be operated on a typical 12V DC aircraft power

system. The DC supply must be free of undesired transients and reasonably stable within the

acceptable supply voltage range of the A16.

It is possible to operate the A16 on 24/28V DC power supplies as well.

For operation with compromised power sources on aircraft it is advised to consider external

power conditioning such as the GL Avionics AvioGuard isolated power supply.

Digital control interfaces

The A16 audio panel provides two RS232 ports as well as a CAN bus interface.

The CAN bus is typically used with control heads from GL Avionics.

RS232 port 1 and RS232 port 2 may be used with EFIS systems. Both ports are equivalent

and can be used at the same time to two different EFIS systems.

Audio input specifications

icrophone inputs Gain range 47db For reference level:

At input sensitivity INI U setting:

0.8Vpp with 6db reserve before clipping.

At input sensitivity AXI U setting:

10mVpp.

At 75% input sensitivity (typical aviation headset

setting): 40mVpp.

Input impedance 240 ohms A/C. 8V DC microphone

bias via 470 ohms.

All other audio

inputs

Gain range 47db For reference level:

At input sensitivity INI U setting: 4.0Vpp.

At input sensitivity AXI U setting: 100mVpp.

Input impedance 250KOhm.

Inhaltsverzeichnis

Andere MGL Avionics Gegensprechanlage Handbücher

MGL Avionics

MGL Avionics V16 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung