Microchip Technology BM71-XPro Bedienungsanleitung

BM71-XPro

BM70/71 XPro User's Guide

Introduction

The BM71-XPro board is a hardware platform designed to evaluate and test the capabilities of the BM71 Bluetooth®

RF module. The BM71-XPro board provides multiple options for rapid prototyping and developing applications. The

board is supported by Atmel Studio, an integrated development platform, which provides predefined applications and

examples.

Features

• USB-UART Bridge (MCP2200) for Host PC Operation

• On Board 3.3V LDO for Power Regulation

• On Board SPI Flash for Storing Firmware Images (DFU OTA)

• Test Point for GPIO Pin (P1_3)

• Reset Push Button

• DIP Switch to Control:

– BM71 operation mode

– LED

– GPIO pin

• Passive RC Filters for PWM and ADC Inputs

• Atmel Studio (ASF3), to Provide Predefined Application Examples

• XPRO Extension Header

• Header Pins for Current Measurement

• Two Power Sources:

– Micro USB

– XPRO Connector

Table of Contents

Introduction.....................................................................................................................................................1

Features......................................................................................................................................................... 1

1. Kit Contents.............................................................................................................................................3

1.1. Reference Documentation............................................................................................................3

2. Hardware Features................................................................................................................................. 4

2.1. Power Supply............................................................................................................................... 4

2.2. USB-UART Bridge........................................................................................................................4

2.3. XPRO Connector..........................................................................................................................4

2.4. DIP Switch....................................................................................................................................5

2.5. Reset Switch................................................................................................................................ 5

2.6. Current Measurement Header......................................................................................................5

2.7. On-board SPI Flash......................................................................................................................5

3. Module Configuration.............................................................................................................................. 7

3.1. Connecting the BM71 XPRO to MBD App in Auto Mode.............................................................7

3.2. Configuring the BM71 Module to Operate in Manual Mode (Host PC)...................................... 10

3.3. Connecting the BM71-XPro to MBD App in Manual Mode (Host PC)........................................14

3.4. Using the BM70/71 MCU drivers................................................................................................23

4. Appendix A. Updating the BM71 Module Firmware.............................................................................. 27

5. Appendix B. Schematics and Bill of Materials.......................................................................................28

6. Agency Certification.............................................................................................................................. 33

6.1. Europe........................................................................................................................................33

7. Document Revision History...................................................................................................................34

The Microchip Website.................................................................................................................................35

Product Change Notification Service............................................................................................................35

Customer Support........................................................................................................................................ 35

Microchip Devices Code Protection Feature................................................................................................ 35

Legal Notice................................................................................................................................................. 35

Trademarks.................................................................................................................................................. 36

Quality Management System....................................................................................................................... 36

Worldwide Sales and Service.......................................................................................................................37

BM71-XPro

1. Kit Contents

The following figure shows the layout of the BM71-XPro board and illustrates the components available in the board:

Figure 1-1. BM71-XPro Board

BM71 Module

Reset Switch

Ground Test Point

Current Measurement Header

Power Supply Selection Header

BM71 LED

USB-UART Bridge (MCP200)

On board SPI Flash

XPRO Connector

Mini USB Connector

DIP Switch

GPIO P1_7 Test Point

Microchip offers several smartphone applications, available for free in both the App Store (iPhone®) and Google

Play™ store (Android™), to evaluate the BM71 module. For details on the currently available apps, please refer to the

BM71 XPro webpage.

1.1 Reference Documentation

For further information, refer to the following:

•BM70/71 Bluetooth® Low Energy (BLE) Module Data Sheet (DS60001372)

•BM70/71 Bluetooth® Low Energy Module User’s Guide (DS50002542).

BM71-XPro

Kit Contents

2. Hardware Features

A description of some of the key features in the BM71-XPro board is provided below. Refer to Figure 1-1 for details of

the kit contents.

2.1 Power Supply

Power the BM71-XPro kit using any of the power sources listed below:

• Micro USB port (J1)

• XPro Connector

Use the J2 header for selecting between these power supply options using a jumper. The green LED (LD1) indicates

that the board is powered by a micro-USB. The micro-USB has ESD and overcurrent protection, and the input to the

module is controlled via an LDO (U1). The BM71-XPro board can be operated in a standalone mode when powered

via the micro-USB.

2.2 USB-UART Bridge

The MCP2200 in the BM71-XPro board provides the option to evaluate the BM71 module in Standalone mode. By

default (out of the box), the BM71 module is set to operate in Auto mode. So, the module, once powered via the

micro-USB, will be able to connect to a peer Bluetooth Low Energy device and open a data pipe for data transfer.

Refer to 3.1 Connecting the BM71 XPRO to MBD App in Auto Mode for details. Apart from powering the board, the

micro-USB port can also be used to evaluate and test the module via a host PC. Microchip provides emulation tools,

such as a UI tool, auto pattern tool, and manual tool (refer to BM71 webpage for details) to evaluate the BM71 via a

host PC. The BM71 module can be set to operate in Manual mode for complete control or in Auto mode for a simple

data pipe application.

2.3 XPRO Connector

The BM71-XPro board has an Xplained Pro (XPRO) header to offer connectivity and control from a host MCU. The

header is based on a standard extension header and its pin details are specified in the following table. The headers

have a pitch of 2.54 mm. For details on the operating the BM71-XPro via a host MCU Xplained Pro board, refer to

3.3 Connecting the BM71-XPro to MBD App in Manual Mode (Host PC).

Table 2-1. Extension Header (J1) Pin Description

Pin# Pin name Description

1 ID ID Chip communication

2 GND Ground

3 ADC1 Connected to pin P2_0 to set system configuration

4 ADC2 Connect to Reset pin of BM71

5 RTS/GPIO Connected to host MCU RTS

6 CTS/GPIO Connected to host MCU CTS

7 PWM+ PWM pin (+) of host MCU

8 PWM- PWM pin (-) of host MCU

9 GPIO Connected to GPIO pin P2_7 (TX_Ind)

10 GPIO Connected to GPIO Pin P1_6 (RX_Ind)

BM71-XPro

Hardware Features

...........continued

Pin# Pin name Description

11 I2C SDA

12 I2CSCL

13 Host MCU Rx Connects to BM71 Tx pin

14 Host MCU Tx Connects to BM71 Rx pin

15 SPI SS SPI SS pin of Flash memory

16 SPI MOSI SPI MOSI pin of Flash memory

17 SPI MISO SPI MISO pin of Flash memory

18 SPI SCK SPI SCK pin of Flash memory

19 GND Ground

20 Vdd Power supply

2.4 DIP Switch

The DIP switch has three switches which provide the functions described in the following table.

Table 2-2. DIP Switch Functions

Switch# Function

1 Manually set the BM71 system configuration. Connected to pin P2_0.

• ON: Memory Programming mode

• OFF: Application mode

2 Turn the Blue LED (LD4) ON/OFF

3 Control the GPIO pin P1_3

2.5 Reset Switch

The Reset push button is connected to the BM71 module reset line. When the Reset button is pressed, it drives the

reset line to ground. The BM71-XPro board has an on-board voltage detected reset IC (MCP112) connected to the

Reset pin of the BM71.

2.6 Current Measurement Header

A J3 header can be used for current measurement.. All power to the BM71-XPro is routed through these header pins.

To measure the power consumption of the module, remove the jumper and replace it with an ammeter. To make sure

only the power consumption of the BM71 module is measured, turn off the blue LED using switch #2 of the DIP

switch.

2.7 On-board SPI Flash

An SST25VF080B SPI Flash memory is included in the BM71-XPro board for nonvolatile firmware storage. This can

be used to update the device firmware for the BM71 or the host MCU.

BM71-XPro

Hardware Features

Note: BM71 Xplained Pro board is intended for use for development, demonstration or evaluation purposes only. It

is not a finished appliance, nor is it intended for incorporation into or reference design for finished appliances that are

made commercially available.

Every effort has been made to minimize electromagnetic emissions from the product. However, under certain

conditions, the system (this product connected to a host application circuit via Xplained Pro extension header for

communicating with External SPI Flash) may emit individual electromagnetic component frequencies which exceed

the maximum values allowed by the standards. The frequency and magnitude of the emissions will be determined by

several factors, including layout and routing of the application with which the product is used. The recommendation is

to add external series resistors on the Xplained Pro Extension Header SPI signals to the External SPI Flash if the

product causes emissions above the permissible limits of the standard. For reference for the BM71 module

placement and layout guidelines please refer the BM71 Module datasheet.

BM71-XPro

Hardware Features

3. Module Configuration

The BM70/71 module supports following modes, which affect the overall Bluetooth Low Energy and hardware

behavior:

•Auto operation configuration or Auto mode: By default, the BM70/71 module is set to operate in the Auto

mode. The Auto mode restricts the available Bluetooth Low Energy operations by only allowing the Bluetooth

Low Energy peripheral to act as a raw data pipe. This is compatible with hosts who only require the BM70/71

module to act as a virtual UART cable between the host and the remote peer device.

•Manual operation configuration or Manual mode: Manual operation provides the host MCU a lot more control

and functional options over the BM71 Bluetooth Low Energy protocol and operation in comparison to the Auto

Operation mode. This configuration is used by a host MCU to leverage the flexibility and feature set offered by

both the Bluetooth Low Energy protocol and the BM71 module (for example: private services and

characteristics).

Note: For more details, refer to the Section 1.1 Operation Overview in the BM70/71 Bluetooth Low Energy Module

User’s Guide (DS50002542).

The simplest method to start evaluating the BM71 is to connect it to a host PC that supports USB CDC virtual COM

(serial) ports and operates in Auto mode. In this mode, the user can directly connect to the BM71 from a peer device

(phone app) and open a raw data pipe. Refer to 3.1 Connecting the BM71 XPRO to MBD App in Auto Mode for

connection procedure. See 3.2 Configuring the BM71 Module to Operate in Manual Mode (Host PC) and 3.3

Connecting the BM71-XPro to MBD App in Manual Mode (Host PC) for an example of Manual mode of operation.

3.1 Connecting the BM71 XPRO to MBD App in Auto Mode

Hardware/Software required:

• BM71-XPro board; Mini-USB cable.

• A PC host supporting USB CDC virtual serial port. BM71-XPro board uses MCP2200 USB to UART bridge. The

drivers can be downloaded from http://www.microchip.com/MCP2200.

• Terminal Emulator application. TeraTerm or CoolTerm is recommended.

• Microchip MBD app for iOS or Android. Available in:

–App Store (iOS) for iPhones.

–Google Play Store for Android phones.

By default, the BM71 module is set to operate in Auto mode. For details on the Auto mode of operation on the BM71

module, refer to section 1.1.2.1 in the BM70/71 User’s Guide (DS50002542).

The procedure to connect the BM71-XPro board to a peer device (phone/table) via host PC is given below:

1. Ensure that the BM71-XPro board is configured as follows:

1.1. Jumper on the J2 header is closed to select USB power option.

1.2. The current measurement jumper on J3 is present.

1.3. Switch 1 (system configuration) on the DIP switch is set to OFF.

1.4. Switch 2 (blue LED) on the DIP switch is set to ON.

2. Connect the BM71-XPro board to a host PC using the mini-USB cable. Ensure that green LED (LD1) is solid

ON indicating USB power.

3. Connect BM71-XPro to a PC host using micro-USB cable.

3.1. Verify the virtual COM port is enumerated on a host PC. If the COM port does not enumerate, the

MCP2200 drivers may be missing from the host PC. If needed, the drivers can be downloaded from

the www.microchip.com/MCP2200 webpage.

3.2. Press the Reset button (SW1) and verify that the blue LED (LD4) is flashing intermittently.

4. Start the Terminal Emulator software. In this example, TeraTerm is used. Configure the serial port settings of

the enumerated COM port as shown in the following figure.

BM71-XPro

Module Configuration

Figure 3-1. TeraTerm Serial Port Setup

5. Open the MBD app on the phone/tablet. Ensure that the Bluetooth is turned ON in the device.

6. On Dashboard, select “BM70”, see the following figure.

Figure 3-2. MBD Dashboard

7. In the follow-up screen, click Scan and “Scan” again at the bottom.

8. Once the scanning process completes, the BM71 module should appear as “BM71_BLE” by default.

BM71-XPro

Module Configuration

Figure 3-3. MBD Scanning Process

9. Click on the “BM71_BLE” to start a connection process. Once connected, the transparent UART service

available on the BM71 module should show up.

Figure 3-4. MBD Connecting to BM71 XPRO

10. Click on “Transfer data to device”. The Transparent UART screen should open (see following figure). The data

pipe is now open.

BM71-XPro

Module Configuration

Figure 3-5. MBD Data Pipe

11. In the serial emulator application (TeraTerm), enter any text and this should show up in the transparent UART

page in the app.

3.2 Configuring the BM71 Module to Operate in Manual Mode (Host PC)

Hardware/Software required:

• BM71-XPro board; Mini-USB cable.

• A PC host supporting USB CDC virtual serial port. BM71-XPro board uses MCP2200 USB to UART bridge. The

drivers can be downloaded from http://www.microchip.com/MCP2200.

• BM71 emulator tools: UI Tool. These tools can be download from the BM71 webpage.

The procedure to change the BM71 to Manual mode via host PC is given below:

1. Ensure that the BM71-XPro board is configured as follows:

1.1. Middle jumper on J2 is closed to select USB power option.

1.2. The current measurement jumper on J3 is present.

1.3. Switch 2 (blue LED) on the DIP switch is set to ON.

2. Connect the BM71-XPro board to the host PC using the mini-USB cable. Ensure that the green LED (LD1) is

solid ON indicating USB power.

3. Connect BM71-XPro board to the host PC using micro-USB cable. Verify the virtual COM port is enumerated

on the host PC. If the COM port does not enumerate, the MCP2200 drivers may be missing from the host PC.

If needed, the drivers can be downloaded from the http://www.microchip.com/MCP2200 web page.

4. Set switch 1 (system configuration) on the DIP switch to ON. Press the Reset button (SW1). The blue LED

(LD4) should turn to a solid ON.

5. Open the UI tool (see the following figure) and Click on ‘Load’.

BM71-XPro

Module Configuration

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Microchip Technology Hauptplatine Handbücher

Microchip Technology

Microchip Technology MCP7382X Bedienungsanleitung

Microchip Technology

Microchip Technology MCP212X Bedienungsanleitung

Microchip Technology

Microchip Technology PICtail Bedienungsanleitung

Microchip Technology

Microchip Technology PICtail MRF24J40MC Bedienungsanleitung

Microchip Technology

Microchip Technology PIC32MX470 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP19035 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP39F521 Bedienungsanleitung

Microchip Technology

Microchip Technology Curiosity Low Pin Count Bedienungsanleitung

Microchip Technology

Microchip Technology dsPICDEM MCHV-3 Bedienungsanleitung

Microchip Technology

Microchip Technology IS2066B Bedienungsanleitung

Microchip Technology

Microchip Technology ATWINC15x0 Series Beilage

Microchip Technology

Microchip Technology HV9805 Bedienungsanleitung

Microchip Technology

Microchip Technology TA100 Bedienungsanleitung

Microchip Technology

Microchip Technology HV2918 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP19117 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP6S2 Series Bedienungsanleitung

Microchip Technology

Microchip Technology MCP4725 SOT-23-6 Bedienungsanleitung

Microchip Technology

Microchip Technology MIC24045 Bedienungsanleitung

Microchip Technology

Microchip Technology AVR-IoT WA Bedienungsanleitung

Microchip Technology

Microchip Technology BM63 Bedienungsanleitung

Microchip Technology

Microchip Technology PIC18F47K42 Curiosity Nano Installationshandbuch

Microchip Technology

Microchip Technology MCP3911 Bedienungsanleitung

Microchip Technology

Microchip Technology ATBTLC1000 Xplained Pro Installationsanleitung

Microchip Technology

Microchip Technology PIC18F16Q41 Curiosity Nano Installationshandbuch

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung