Microsoft TM--1104-3 Bedienungsanleitung

Size А3 / А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

6574190580

TELEVISION MODULE

ТМ-1104-3

Operating Manual

ТЭ3.623.912-03РЭ

CONTENTS

1 Description and Operation 6

1.1 Description and Operation of Device 6

1.1.1 Application 6

1.1.2 Main Technical Parameters 7

1.1.3 Device Contents 7

1.1.4 Device Structure and Operation 8

1.1.4.1 Video Signal Generation, Processing

and Displaying System 8

1.1.4.2 Genlocking system 9

1.1.4.3 Control System 10

1.1.4.4 Automated Checkout System 15

1.1.4.5 Chronometrical Information Input System 21

1.1.4.6 Power Supply System 21

1.1 4.7 Auxiliary Communication System 23

1.1.4.8 Device Design 24

1.1.4.9 Measurement Instrumentation, Tools and Accessories 25

1.1.4.10 Marking 25

1.2 Description and Operation of Device Component Parts 25

1.2.1 ВС-2TelevisionMonitor 25

2 Operation 29

2.1 Operating Conditions and Safety Rules 29

2.2 Device preparation for Operation 29

2.2.1 Safety Precautions during Installations 29

2.2.2 External Examination ofDevice 30

2.2.3 Initial Position of Controls before Use of Device 30

2.2.4 Interconnection with other Devices 30

2.2.5 Switching-On and Testing of Device 30

2.3 Usage of Device 31

2.3.1 Personnel Operation during Intended Use of Device 31

2.3.2 Checking Operability of Device 31

2.3.3 Possible Troubles and Remedies thereof 32

2.3.4 Switching the Device off 34

2.3.5 Safety Precautions during Usage of Device 34

2.4 Measures under Emergency Conditions 34

3Maintenance 35

3.1ServicingofDevice 35

3.1.1 General Guidelines 35

3.1.2 Safety Measures 35

3.1.3 Maintenance Execution Order 35

3.1.4 Replacement of Modules in Device 36

3.1.5 Device Operability Check-Up 38

Appendix АList of Abbreviations and Special Terms

Used in this Manual 49

Appendix B Figure B1 General View of ТМ-1104-3 Television Module 41

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ

Liff P. Pages

3 41

Television Module

ТМ-1104-3

Operating Manual з/н4 ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

Operating Manual ТЭ3.623.912-03РЭ is intended for studying the content, operation

principle, parameters and characteristics of the ТМ-1104-3 ТЭ3.623.912-03 television

module to help correct operation and full use of the technical capabilities thereof.

For studying and operation of the ТМ-1104-3 ТЭ3.623.912-03 television module the

following additional documents should be guided by:

ТМ-1104-3 television module:

- electric connection diagram ТЭ3.623.912-03Э4;

- component list ТЭ3.623.912-03ПЭ4;

- block diagram ТЭ3.623.912-03Э2.

МТК-110МЭ television complex:

- general electric diagram ТЭ1.133.110-02Э6;

- block diagram ТЭ1.133.110-02Э2;

- operating manual ТЭ1.133.110-02РЭ.

The list of the special terms and abbreviations used in the present Manual is given in

Appendix A.

1 DESCRIPTION AND OPERATION

1.1 Description and Operation of Device

1.1.1 Application

The ТМ-1104-3 ТЭ3.623.912-03 television module, hereinafter referred to as "device",

when used as a part of the TV-complex is intended for:

- commutation of video signals from TVDs to TVMs of the TV-complex;

- displaying of video information from TVDs of the TV-complex on the screen of the

ВС-2 TVM, that is built into the device;

- generation and reception of control signals during data exchange via RCLI channels

with the TM-1215-4 control modules and ТМ-1213 terminal module of the TV-complex;

- generation and reception of control signals during data exchange via RCLI channels

with the ТМ-1304 combined modules of the TV-complex;

- generation and transmission of the DGP signal to the ТМ-1304 combined modules of

the TV-complex;

- reception of chronometrical information from device "Гном-2МЭ", indication of that

on the screen of the ВС-2 TVM and its transmission to the ТМ-1213 terminal module of the

TV-complex via RCLI channel;

- supplying the ТМ-1304 combined modules, TM-1215-4 control modules and

TM-1213 terminal module of the TV-complex with a feeding voltage of plus 27 V;

- gathering and processing of information on the TV-complex state;

- indication of information on the TV-complex state on the screen of the ВС-2 TVM;

- indication of information on the TV-complex state with the built-in LEDs;

- checkout of the equipment of the TV-complex during maintenance and operation.

To provide easy restoration of the device some modules and units of the BSP are built

immediately into the device.

The device provides the parameters and characteristics given below under the

following operating conditions:

- ambient temperature from 0 to 40 °С;

- relative humidity up to 98% at a temperature of 35 °С;

- air pressure from 600 mm Hg to 1520 mm Hg;

- sinusoidal vibration in a frequency range of 5 to 60 Hz at an acceleration amplitude

of up to (2,0 ± 0,4)g.

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

1.1.2 Main Technical Parameters

The device has the following main technical parameters:

- number of video signal inputs - 21;

- number of video signal outputs - 4;

- swing of input and output video signals - (1 ±0,3) V;

- load resistance in video signal circuit - (75 ±5%) Ω;

- video channel bandwidth, at least 7,3 MHz;

- scanning - interlaced, 625 lines, 25 frames a second;

- number of RCLI channels for data exchange with the TM1215-4 control module and

ТМ-1213 terminal module - 4;

- number of RCLI channels for data exchange with the ТМ-1304 combine modules - 6;

- lock mode - autonomous;

- number of DGP output signals - 6;

- two independent channels for receiving chronometrical information from device

"Гном-2МЭ";

- supply voltage - three-phase, from 180 to 231 V;

- feeding voltage frequency - (50 ±1) Hz;

- power consumption - no more than 500 VA, including total power consumption of

external load not exceeding 350 VA;

- continuous operation time - 5000 h;

- overall dimensions – no more than 1722 x 360 x 629 mm;

- weight, maximum - 125 kg.

1.1.3 Device Contents

The device includes the parts shown in Table 1.

Table 1

Designation Code Part Name Qty.

ТЭ2.045.544 ВС-2 Television monitor 1

ТЭ2.067.408 ФСП-3ВInterference rejection filter 6

ТЭ2.072.492 ЭМ-1211 Diagnostics module 1

ТЭ2.201.769 ЭМ-1213 Power supply unit 3

ТЭ2.242.434-01 ЭМ-1204-1 Videoswitch module 1

ТЭ2.242.435-01 ЭМ-1205-1 Videoswitch module 1

ТЭ2.275.261 ЭМ-1242 Interface unit 1

Table 1 (continued)

Designation Code Part Name Qty.

ТЭ3.057.439-01 ЭМ-1209-1 Controller 1

ТЭ3.679.117-01 ЭМ-1212-1 Control module 1

ТЭ5.883.022 Assembly unit 1

1.1.4 Device Structure and Operation

Modules and units of the device form several functional systems, that are parts of the

corresponding systems of the TV-complex. This functional systems are listed below:

- system providing generation, processing and displaying of video signals;

- genlocking system;

- control system;

- automated checkout system;

- chronometrical information input system;

- power supply system;

- auxiliary communication system.

Most modules included by the device contain units that are parts of different systems.

The description of the device and operation thereof refers to elements in the

ТМ-1104-3 ТЭ3.623.912-03Э4 TV-module electric connection diagram and the

ТЭ1.133.110-02Э6 TV-complex general electric diagram.

1.1.4.1 Video Signal Generation, Processing and Displaying System

The system of video signal generation, processing and displaying provides:

- “mirror” rotation of the image arriving from the KT-257 TV-camera;

- multiplexing of 21 input video signals to five outputs;

- generation of a video signal for displaying information on the TV-comlex state on the

ВС-2 TVM;

- displaying of video information from the TVDs of the TV-complex on the screen of the

ВС-2 TVM.

The device contains three main modules of the video signal generation, processing

and displaying system:

- videoswitch module, ЭМ-1204-1 (А31);

- videoswitch module, ЭМ-1205-1 (А32);

- ВС-2 television monitor (А11);

- ЭМ-1211 diagnostics module (А21) that generates the video signal containing data

on the TV-complex state.

The ЭМ-1205-1 videoswitch module converts the inverse image from the KT-257

TV-camera (created by the lens of pull-out optical device “Сигнал-3”) to an erect image. The

ЭМ-1205-1 videoswitch module provides several modes of image rotation: by line, by frame

and by both at the same time. The rotation mode is set by parallel binary code that is used for

remote control. The code comes from the ЭМ-1204-1 videoswitch module.

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

The video signal from the KT-257 TV-camera comes to connector X1 of the device

and then – to the input of the ЭМ-1205-1 videoswitch module. The ЭМ-1205-1 videoswitch

module contains a DAC, an ADC and a PLIC. The ADC performs conversion of the analog

video signal into a digital one. Then, the PLIC provides writing of the data into the internal

RAM and reading the content of the RAM in an inverse order thereby performing the image

rotation required. The rotation process is initiated on a remote control command. From the

output of the PLIC the digital data come to the DAC that does the conversion into an analog

output video signal.

The ЭМ-1204-1 videoswitch module performs multiplexing of 21 input video signals to

five outputs in accordance with remote control commands that come from the ЭМ-1209-1

controller via RCLI lines.

The ЭМ-1204-1 videoswitch module contains an analog matrix multiplexer providing

commutation of 24 input signals to 6 outputs. The device employs only 21 inputs and five

outputs. The matrix multiplexer is driven by a built-in microcontroller (MC) receiving

commands from the ЭМ-1209-1 controller.

The video signal from the output of the ЭМ-1205-1 videoswitch module comes to input

1 of the ЭМ-1204-1 videoswitch module. The signals from the TVDs of the TV-complex are

connected to inputs 2 to 20. "Video Input 21" of the ЭМ-1204-1 videoswitch module is

reserved and not used in the TV-complex. The output video signals of the ЭМ-1204-1

videoswitch module are assigned as follows:

"Video Output 1" via connector X22 of the device comes to TVM ВС-2-1 No.1 of the

TV-complex (first CP of TV-complex);

"Video Output 2" via connector X23 of the device comes to TVM ВС-2-1 No.2 of the

TV-complex (second CP of TV-complex);

"Video Output 3" via connector X24 of the device comes to the ВС-1-1 No.1 of the TV-

complex (third CP of the TV-complex);

"Video Output 4" comes to connector X25 of the device and is not used in the TV-

complex;

"Video Output 5" comes to the video input of the ЭМ-1211 diagnostics module and

then - to the ВС-2 TVM.

The ЭМ-1211 diagnostics module performs switching between video signals for the

ВС-2 TVM coming from the ЭМ-1204-1 videoswitch module and a diagnostics signal that is

generated by the ЭМ-1211 diagnostics module by itself.

Commutation of video signals is done by pressing the buttons on the front panel of the

ЭМ-1211 diagnostics module. By pressing button SELECT the video signal from the

ЭМ-1204-1 videoswitch module (from the TVD chosen on the ЭМ-1212-1 control module) is

connected to the ВС-2 TVM. Pressing button ENTER provides connection of the video signal

formed in the ЭМ-1211 diagnostics module, containing data on the TV-complex state, to the

screen of the ВС-2 TVM.

1.1.4.2 Genlocking System

The genlocking system provides centralized synchronization of all the TVDs of the

complex by forming DGP signals on the six output connectors of the device. The DGP signal

constitutes a pulse sequence with a swing of 3 V, frequency of 15625 Hz and duration of

5 µS. Every 625-th pulse has a duration of 12 µS. The centralized synchronization reduces

the mutual interference level and simplifies video signal processing.

The main unit of the genlocking system is the EM-1209-1 controller. The PLIC of the

unit forms the DGP signal basing on clock pulses of a quartz oscillator and supplies it to the

six DGP outputs via a buffer amplifier. This signals are fed to connectors X26-X31 of the

device and finally arrive to the TM-1304 combined modules. One DGP output (connector

X31) is reserved and not used in the TV complex.

1.1.4.3 Control System

The functional control system (CS) is formed by the ЭM-1209-1 controller (A33) along

with microcontrollers and microprocessors of the main device modules interconnected via

RCLI lines. The ЭM-1209-1 controller constitutes a dedicated computer performing the main

control functions of the TV complex. The microcontrollers and microprocessors that are parts

of the ЭM-1204-1 videoswitch module (А31), ЭМ-1211 diagnostics module (А21), ЭM-1212-1

control module (А22), and ЭM-1242 interface unit (А23) perform local control functions.

The control system provides:

- communication with the TM-1215-4 control modules and the TM-1230 control module

of the TV complex CPs to receive control instructions from the module buttons;

- input of control instructions from the ЭM-1212-1 control module, that is a part of the

device, during the TV complex operation check.

- processing of control instructions and output of instructions to the execution units of

the device and other modules of the TV complex to provide power supply and control of the

TVDs, correction and commutation of video signals, centralized genlocking and video

recording.

- receiving and analysis of replies of execution units and indication of instruction

fulfillment results;

- preparation and output of data about the state of the TV-complex to the automatic

checkout system (ACS).

The ЭM-1209-1 controller is the main control element of both the device control

system and the whole TV complex. The working software of the controller is written to ROM

and provides control of the TV complex via serial duplex communication channels. The

ЭM-1209-1 controller incorporates a power supply supervisor and a watchdog timer,

controlling the working program execution and automatically resetting the system in case of a

fault. The ЭM-1209-1 controller provides 14 serial duplex interface channels (RCLI) and an

RS-232 channel. The working program can be reset by pressing the RESTART button,

mounted on the front panel of the controller. The ЭM-1209-1 controller is installed on the third

floor of the device in the rightmost row (see Appendix B, pos.13). To the left of that the two

ЭM-1209-1 controllers of the BSP are installed.

The modules that are parts of the device as well as other modules included by the

TV-complex are controlled via RCLI channels.

The RCLI channels have the following parameters:

- loop-type channel, duplex, four-wire, two wires are used for output datastreams (data

transmission lines) and two wires are used for input datastreams (data reception lines);

- data transmission and reception circuits are galvanically decoupled;

- baud rate - 19200;

- number of data bits - 8;

- number of stop bits – 1;

- LSB is transferred first;

- pause, stop bit and logic one are transferred as current from 0 to 1 mA;

- start bit and logic 0 are transferred as current from 15 to 25 mA;

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

- receiver operation threshold is from 5 to 8 mA.

Data in the RCLI channels is transmitted as byte arrays. Data arrays are transferred

with a frequency from 10 to 25 Hz. The pause between arrays is no less than 1 ms. Pause

between neighboring bytes within an array is no more than 100 µS. Every array ends with a

check sum. Data exchange in RCLI channels is started by the ЭМ-1209-1 controller by

transmission of the corresponding command instruction arrays. On reception of the command

instruction array all the units and modules of the TV-complex start transmission of reply

arrays.

Data exchange between the ЭМ-1209-1 controller and the ТМ-1304 No.1 -

ТМ-1304 No.5. combined modules is performed via channels " RCLI 1" – " RCLI 5". During

this exchange the datastream passes through assembly modules, ТМ-1308 No.1-

ТМ-1308 No.3.

Every command array consists of nine bytes and contains the following data:

command to switch on the power supplies of four TVDs, video signal correction factors for

four TVDs, type of synchronizing pulses and delay of those for synchronization of four TVDs,

instructions for control of TVD modes. The reply arrays contain data on functioning of the

modules that are parts of the ТМ-1304 combined modules, supply voltage presence on four

TVDs, presence of video signals from four TVDs, diagnostic information from four TVDs.

Data exchange between the ЭМ-1209-1 controller and the ТМ-1213 terminal module

is performed via channel " RCLI 7". During this exchange the datastream passes through

connector X38 of the device and the ТМ-1308 No.4 assembly module.

The command array contains commands to light up the LEDs of the ТМ-1215-4 No.1

and the ТМ-1230 control modules, commands for control of the ДЕ-118-1 VRD, data for

mixing into the video signal before video recording (abbreviated name of TVD, date and

time). The reply array contains the codes of the buttons pressed on the control modules,

ТМ-1215-4 N 1 and ТМ-1230, and also information about the state of the ДЕ-118-1 VRD.

Data exchange between the ЭМ-1209-1 controller and the ТМ-1215-4 No.2 control

module is performed via channel " RCLI 8". During this exchange the datastream passes

through connector X38 of the device, the ТМ-1308 No.4 assembly module and the ТМ-1201

No.1 terminal module. The command array contains commands to light up the LEDs of the

ТМ-1215-4 No.2 control module. The reply array contains the codes of the buttons pressed.

Data exchange between the ЭМ-1209-1 controller and the ТМ-1215-4 No.3 control

module is performed via channel " RCLI 9". During this exchange the datastream passes

through connector X39 of the device, the ТМ-1308 No.5 assembly module and the

ТМ-1201 No.2 terminal module. The command array contains commands to light up the

LEDs of the ТМ-1215-4 No.3 control module. The reply array contains the codes of the

buttons pressed.

The ЭМ-1209-1 controller transmits data to the ЭМ-1211 diagnostics module via

channel " RCLI 11". The data array contains information on data transfers between the

ЭМ-1209-1 controller and all the peripheral modules, information on the state and control of

all the TVDs and VRDs.

Channel " RCLI 12" is used for data exchange between the ЭМ-1209-1 controller and

the ЭМ-1212-1 control module. The command array contains instructions for controlling the

LEDs of the ЭМ-1212-1 control module. The reply array contains the codes of the buttons

pressed.

Channel " RCLI 13" is used for data exchange between the ЭМ-1209-1 controller and

the ЭМ-1242 interface module. The command array contains a request for transferring

chronometrical information from the first or the second channel of the ЭМ-1242 interface

module. The reply array contains chronometrical information from the requested exchange

channel of the ЭМ-1242 interface module.

Channel " RCLI 14" is used for data exchange between the ЭМ-1209-1 controller and

the ЭМ-1204-1 videoswitch module. The command array contains instructions for

commutation of the input video signals to the six outputs. The reply array contains

information on the instruction execution.

Channels " RCLI 6" and " RCLI 10" are brought out to connectors X37 and X39 of the

device. They are reserved and not used in the TV-complex.

The RS-232 channel is brought out on connector X43 of the device. This channel is

used for setup and debugging of the TV-complex.

The ЭМ-1209-1 executes the program stored in its non-volatile memory. This program

periodically, with a frequency of 10 to 25 Hz, carries out the following actions:

- communication with the ТМ-1215-4 control modules, TМ-1230 control module and

ЭМ-1212-1 control module via the RCLI channels;

- handling of commands coming from the ТМ-1215-4 control modules, TМ-1230

control module and ЭМ-1212-1 control module when their buttons are pressed;

- forming of control instructions for all the modules connected to the ЭМ-1209-1 via the

RCLI channels.

- transferring of instructions via the RCLI channels and interrogation of the ЭМ-1204-1

video signal commutation module, ЭМ-1242 interface module, ЭМ-1202 control and

synchronization modules in the ТМ-1304 combined modules, ЭМ-1241 control modules in

the ТМ-1220-1 optical TV-units and the КТ-257 TV camera;

- forms and transfers the diagnostic data to the ЭМ-1211 diagnostics module.

The ЭМ-1212-1 control module (Fig.1) provides manual command input for the

ЭМ-1209-1 controller with the buttons mounted on the front panel and LED indication of

execution of the following commands:

- switching on and off of any of the 20 TVDs of the TV-complex with buttons GROUP1-

GROUP5, CHANNEL1-CHANNEL4, OFF.

- enabling the night mode of the KT-257 TV-camera with button NIGHT MODE;

- control of the selected ТМ-1220-1 optical TV-module with button TEST ON.

- indication of location of faulty TVDs under servicing or servicing completion with

buttons TVD TO CHECK and TVD FROM CHECK.

- testing LEDs and buttons of the ЭМ-1212-1 control module with button TEST of the

ЭМ-1212-1.

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

Fig. 1 – Front panel of the ЭМ-1212-1 control module.

Functioning of the ЭМ-1212-1 control module as a part of the control system is

provided by microcontroller CS, PLIC, interface and buttons with LEDs. The microcontroller

(MC) together with the PLIC inquires the buttons. On request from the ЭМ-1209-1 controller

the MC forms a reply array with the codes of the buttons pressed and transfers it via the

RCLI channel to the ЭМ-1209-1 controller.

The MC of CS receives from the ЭМ-1209-1 controller a command array with

instructions for lighting up the LEDs and switches on the corresponding LEDs by means of

the PLIC. The working program of the ЭМ-1209-1 controller analyses the button state and

decides whether to light up the LEDs.

Correspondence between group numbers, channel numbers, TVD installation places

and the designation on the ТМ-1215-4 control module is shown in Table 2.

The ЭМ-1211 diagnostics module has a microprocessor and an interface receiving

arrays with data on the CS state from the ЭМ-1209-1 controller and provide visualization of

the data in video frames of the ACS.

The ЭМ-1204-1 videoswitch module contains a MC and an interface that receive

instructions from the ЭМ-1209-1 controller for commutation of video signals and control their

execution.

Table 2

Group-

channel Place of TVD installation Video signal

source

Designation on

ТМ-1215-4

1-1 Device ″Сигнал-3″КТ-257 PERISCOPE

1-2 Fore end, −6 frame ТМ-1220-1 FE –6FR

1-3 1 room, 1 deck, starboard side Неотон-08-2 1R 1D STB

1-4 1 room, 2 deck Неотон-08-1 1R 2D

2-1 1 room, 1 deck, port side Неотон-08-1 1R 1D PS

2-2 Superstructure, 20 frame ТМ-1220-1 SUPRSTR 20FR

2-3 3 room, 1 deck Неотон-08-2 3R 1D

2-4 3 room, 3 deck Неотон-08 3R 3D

3-1 4 room, 1 deck Неотон-08-2 4R 1D

3-2 BF, winch automated communication

system ТМ-1220-1 WINCH ACS

3-3 4 room, 2 deck, starboard Неотон-08-1 4R 2D STB

3-4 4 room, 2 deck, port side Неотон-08-1 4R 2D PS

4-1 5 room, port side Неотон-08-2 5R PS

4-2 5 room, starboard Неотон-08-2 5R STB

4-3 Pod, winch sonar system ТМ-1220-1 WINCH SS

4-4 4 room, 2 deck, PCS Неотон-08 4R 2D PCS

5-1 6 room, 1 deck, aft Неотон-08-1 6R 1D A

5-2 6 room, 1 deck, fore Неотон-08-1 6R 1D F

5-3 Tiller compartment Неотон-08 TC

5-4 Pod, 108 frame ТМ-1220-1 POD 108FR

ЭМ-1212-1

TROUBLE

GROUP CHANNEL TVD CONTROL TROUBLE

ЭМ-1204-1 ТМ-1304 N1

ЭМ-1205-1 ТМ-1304 N2

ЭМ-1209-1 ТМ-1304 N3

ЭМ-1242 ТМ-1304 N4

ЭМ-1213 N1 ТМ-1304 N5

ЭМ-1213 N2

ЭМ-1213 N3 ТМ-1215-4 N1

ТМ-1215-4 N2

ТМ-1215-4 N3

OFF

The ЭМ-1242 interface unit contains a MC and a PLIC that form an array with

chronometrical data on request from the ЭМ-1209-1 controller.

The ЭМ-1209-1 controller working program provides various priorities for the

ЭМ-1212-1 and ТМ-1215-4 control modules as per enabling and control of the TVDs. The

ЭМ-1212-1 control module has the highest control priority. The second comes the

ТМ-1215-4 No.1 control module, then - the ТМ-1215-4 No.2 control module and

ТМ-1215-4 No.3 control module.

The ЭМ-1209-1 prohibits accidental enabling the night channel of the KT-257

TV-camera in the day time. On the first press on button PERISCOPE NIGHT on any of the

ТМ-1215-4 control modules, the ЭМ-1209-1 controller will switch on the day channel of the

ТМ-1213

МТК-110МЭ ДЕ-118-1

FUSE

NIGHT

MODE

TEST

TVD TO

CHECK

4 TVD

FROM CHECK

TEST ЭМ-1212-1

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

KT-257 TV-camera. If button PERISCOPE NIGHT is pressed again the night channel of the

KT-257 TV-camera will be switched on in at least 5 s since the day channel switch-on. If the

night channel of the KT-257 TV-camera has already been switched on and button

PERISCOPE NIGHT on the other ТМ-1215-4 control module is pressed, the signal of the

night channel will be connected to the TVM without delay. ЭМ-1211

The ЭМ-1209-1 controller prohibits the TM-1215-4 control module with the lowest

priority from execution of the following control commands: TROUBLE

- input a test into the TM-1220-1 optic-television module if it was already switched on

from the ЭМ-1212-1 control module or from a ТМ-1215-4 control module having a higher

priority;

ENTER

- switch on the day channel of the KT-257 TV-camera if the night channel was

switched on from the ЭМ-1212-1 control module or from a ТМ-1215-4 control module having

a higher priority;

- switch on the night channel of the KT-257 TV-camera if the day channel was

switched on from the ЭМ-1212-1 control module or from a ТМ-1215-4 control module having

a higher priority; SELECT

The ЭМ-1209-1 controller prohibits to switch on the KT-257 TV-camera and the

TM-1220-1 optic-television modules from the ТМ-1215-4 No.3 control module. If an attempt

at switching on this units occurs, light-emitting diode NO TVD lights up on the

ТМ-1215-4 No.3 control module.

RESTART

The ЭМ-1209-1 prohibits to enable video recording from the ТМ-1215-4 No.2 и

ТМ-1215-4 No.3 control modules. On pressing button RECORD ON on this modules light-

emitting diode NO CTRL lights up.

The ЭМ-1209-1 prohibits controlling the ДЕ-118-1 VRD from the front panel of the

TM-1230 control module, if prior to that the registration mode was activated on the

ТМ-1215-4 No.1 control module.

A TVD generating an abnormal image undergoes checking and servicing. The

ЭМ-1209-1 controller provides indication of the servicing mode from the ЭМ-1212-1 control

module with recording the number of the ТМ-1215-4 control module from which the TVD was

forwarded for servicing. During this the power supply remains connected to the TVD and the

video signal of the TVD comes to the corresponding TVM. On enabling the TVD under

servicing from any of the ТМ-1215-4 control modules or ЭМ-1212-1 control module light-

emitting diode TVD TO CHECK lights up thereon.

The ЭМ-1209-1 controller allows to take a TVD out of servicing only from the

ЭМ-1212-1 control module panel.

1.1.4.4 Automated Checkout System

The automated checkout system (ACS) is intended for continuous supervision over

the state of all the modules and units of the device, gathering of data on the state of units and

modules of the TV-complex. The ACS analyses the incoming data and indicates the state of

the TV-complex modules and units by means of the LEDs and the screen of the ВС-2 TVM.

The ЭМ-1211 diagnostics module (А21) is the main module of the ACS of the device

and the TV-complex also. The ACS comprises the following modules of the device:

- ЭМ-1212-1 control module (А22);

- ЭМ-1209-1 controller (А33);

- ВС-2 television monitor (А11).

Fig. 2 – Front panel of ЭМ-1211 diagnostics module.

The ЭМ-1211 diagnostics module constitutes a special computer whose working

software is written into the ROM by Manufacturer. It has a built in power supply supervisor

and a watchdog timer automatically controlling the working program execution and resetting

the system in case of a fault. The ЭМ-1211 diagnostics module includes a video adapter

forming the video signal and a switch connecting either the external signal or the adapter

signal to the common output. The 55-channel ADC measures the incoming d.c. voltages from

minus 30 to plus 30 V with a ratio error of no more than 0,2%. The ЭМ-1211 diagnostics

module has an RS-232 and a RCLI interface channels. There are five buttons and one LED

on the front panel of the ЭМ-1211 diagnostics module (Fig.2). The LED indicates a fault in

the TV-complex. Button ENTER outputs the ACS frame No.1 on the ВС-2 TVM screen. The

arrow buttons allow switching between frames of the ACS. Button SELECT switches the

video signal from the ЭМ-1204-1 videoswitch module to the screen of the ВС-2 TVM. Button

RESTART forces reset of the working program. The ЭМ-1211 diagnostics module is installed

on the second floor of the device in the leftmost row (Fig. B1, pos.3).

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

The ADC of the ЭМ-1211 diagnostics module samples the d.c. voltages from the three

ЭМ-1213 power supply units, outputs of fuses F1-F16, power supply units built into the

device modules and control voltages +27V from connectors X38 and X39. The ЭМ-1211

diagnostics module measures these voltages and finds faulty modules that fall out of the

corresponding tolerances.

Via a RCLI channel the diagnostics module receives data from the ЭМ-1209-1

controller on the state of the TV-complex units and modules. This information is prepared

during data exchanges via the RCLI channels and contains data on the presence of feeding

voltages and video signals, character of data exchanges between different modules of the

TV-complex, state of the TVDs, VRDs and the ТМ-1215-4 control modules. The ЭМ-1211

diagnostics module transfers data for light indication of faulty units and modules to the

ЭМ-1212-1 control module via a separate RCLI channel.

The ЭМ-1212-1 control module forms three video frames of the ACS for indication of

the TV-complex state on the screen of the ВС-2 TVM.

The ACS frame No.1, "STATE OF МТК-110МЭ" (Fig.3), is formed on pressing button

ENTER. In this frame enabled modules and units are shown as their codes against a light

background, disabled – as theirs codes against a dark background and faulty ones – as their

codes against a blinking background.

The states of the main modules and fuses F1-F16 of the device are shown in the

upper part of the frame. The state of the ТМ-1215-4 No. 1- ТМ-1215-4 No.3 control modules

is shown below. The ТМ-1215-4 No.1 interacts with the ТМ-1213 terminal modules having

the ЭМ-1240 interface unit therein and the ДЕ-118-1 VRD. This devices are grouped

together in the frame. Near the ДЕ-118-1 VRD its state is shown. The following states of the

VRD are shown: "STOP", "OFF", "RECORD", "PLAY", "PAUSE", "REWIND <<", "FAST

FORWARD >>", "NO VIDEO CASSETTE", "VRD TROUBLE", "NO CONTROL".

The five columns of the units related to the ТМ-1304 No.1 - ТМ-1304 No.5 combined

modules are shown below. There are the states of the ЭМ-1202 control and synchronization

modules, ЭМ-1203 video amplifier modules, БПИ-183-аpower supply units incorporated by

the ТМ-1304 combined modules shown togethes with the states of the four TVDs connected

to each ТМ-1304 module depending on their location. In the lower area of the frame are

shown the data and time that are received by the ЭМ-1242 interface unit from device

"Гном-2МЭ". In case of signal absence in any of the channels for exchange with device

"Гном-2МЭ" dashes are displayed instead of date and time.

The number of the ACS frame No.2 is shown in the right lower corner.

The ACS frame No.2, "STATE OF МТК-110МЭ TVDs" is shown in Fig.4.

The left column, "N", shows the numbers (group-channel) of the TVDs. The group

number is the number of the ТМ-1304 combined module. The channel number corresponds

to the TVD connected to this ТМ-1304 combined module.

The "NAME" column contains the location of the TVD.

The "CODE" column contains the code of the TVD.

STATE OF МТК-110МЭ

ТМ–1104–3

Fig.3 –ACS Frame No.1 "STATE OF МТК-110МЭ".

17 18

ЭМ–1212-1 ЭМ–1242 ЭМ–1204-1 ЭМ–1205-1 ЭМ–1209-1

ЭМ–1213 N1 ЭМ–1213 N2 ЭМ–1213 N3

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F15

F14 F16

ЭМ–1211

ТМ–1215–4 N1 ТМ–1215–4 N2 ТМ–1215–4 N3

ТМ–1213

ЭМ–1240

ДЕ–118–1=> NO VIDEO CASSETTE

ТМ–1304 N1 ТМ–1304 N2 ТМ–1304 N3 ТМ–1304 N4 ТМ–1304 N5

ЭМ–1202 ЭМ-1202 ЭМ-1202 ЭМ-1202 ЭМ-1202

ЭМ-1203 ЭМ-1203 ЭМ-1203 ЭМ-1203 ЭМ-1203

БПИ–183-аБПИ-183-аБПИ-183-аБПИ-183-а

БПИ-183-а

PERISCOPE 1R 1D PS 4R 1D 5R PS 6R 1D A

FE–6FR SUPRSTR 20FR WINCH ACS 5R STB 6R 1D F

1R 1D STB 3R 1D 4R 2D STB WINCH SS TC

1R 2D 3R 3D 4R 2D PS 4R 2D PCS POD 108FR

DATE AND TIME FROM "ГНОМ –2МЭ" DEVICE

CHANNEL 1 ЭМ-1242 CHANNEL 2 ЭМ-1242

30–01 –05 12:45:30 30–01–05 12:45:39 N1

P. P.

Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data

Size А3 /А4

Signature and Data

Invent N of doubl

Subst. of invent N

Signature and Data

Invent N of orig.

Fig.4 –ACS Frame No.2 "STATE OF МТК-110МЭ TVDs".

The "ON" column contains the numbers of the CPs, from which the TVDs were

switched on. If the same TVD was switched on from several CPs, their numbers are

displayed via blanks. The device including the ЭМ-1212-1 control module and the ВС-2 TVM

is designated as CP No.4 of the TV-complex. The "CTRL" column shows the number of a CP

of the TV-complex and the remote control command being executed from this CP.

The "CHECK" column shows the number of CP of the TV-complex from which the

TVD was chosen for servicing.

The number of ACS frame No.2 is shown in the right lower corner.

The ACS frame No.3, "MODULE FEEDING VOLTAGES" is shown in Fig.5.

Fig. 5 – ACS Frame No.3 "MODULE FEEDING VOLTAGES".

The feeding voltages are symbolically shown as horizontal lines with four marks. The

leftmost mark represents the zero point. The next three marks represent the minimum,

nominal and maximum values of the voltage. The length of a line denotes the voltage in a

non-linear scale. The position of the minimum mark corresponds to 95% of the rated voltage.

The position of the rightmost mark corresponds to 105% of the rated voltage. If the voltage

controlled falls out of the tolerance limits, the line blinks that is a sign of a fault in the module.

The output voltages of the three ЭМ-1213 power supply units are displayed in the upper part

of the frame. The supply voltages produced by power supply cells in the corresponding

modules are displayed below. The number of ACS frame No.3 is shown in the right lower

corner.

Frames are switched over by pressing the arrow buttons on the front panel of the

ЭМ-1211 diagnostics module (Fig.2).

The ЭМ-1212-1 control module indicates faulty modules of the TV-complex with the

LEDs, in accordance with the information received from the ЭМ-1211 diagnostics module via

the RCLI channel. Light-up of the LED of the МТК-110МЭ indicates a fault in some unit or

module not represented on the ЭМ-1212-1 control module front panel. To get more specific

information about the faulty module, the ACS frame No.1 should be output on the TVM

screen.

19 20

N NAME CODE ON CTRL CHECK

1-1

1-2

1-3

PERISKOPE

FE-6F

1D STB

КТ-257

ТМ–1220-1

НЕОТОН-08-2

2 3

----

1 DAY

2 TEST

---

1-4

2-1

2-2

2-3

1D PS

SUPRST

20F

НЕОТОН-08-1

ТМ–1220-1

НЕОТОН-08-2

----

---

2-4

3-1

3-2

WINCH ACS

НЕОТОН-08

НЕОТОН-08-2

ТМ–1220-1

----

---

3-3

3-4

4-1

4-2

2D STB

2D PS

STB

НЕОТОН-08-1

НЕОТОН-08-2

----

---

4-3

4-4

5-1

WINCH SS

2D PCS

1D A

ТМ–1220-1

НЕОТОН-08

НЕОТОН-08-1

----

---

5-2

5-3

5-4

1D F

POD 108F

НЕОТОН-08-1

НЕОТОН-08

ТМ–1220-1

----

---

STATE

МТК

–

110МЭ

TVDs

+6V1

+6V2

+6V3

-6V1

+27V1

+27V2

+5V

-5V

ЭМ–1204-1

+5V

ЭМ–1205-1

+5V

ЭМ–1209-1

+5V

ЭМ–1242

ЭМ-1213

MODULE FEEDING VOLTAGES

N2 N3

Inhaltsverzeichnis

Andere Microsoft TV-Zubehör Handbücher

Microsoft

Microsoft TV Photo Viewer Bedienungsanleitung

Beliebte TV-Zubehör Handbücher anderer Marken

pass & seymour

pass & seymour GFCI Bedienungsanleitung

Skyvue

Skyvue SECURITY ALARM DEVICE Bedienungsanleitung

Niles

Niles C5-RFWM Bedienungsanleitung

Philips

Philips SWA3554 Bedienungsanleitung

Sony

Sony CRU-52X1 Bedienungsanleitung

BVE

BVE MATRIX 7xe Bedienungsanleitung

Epson

Epson Moverio BT-100 Bedienungsanleitung

Philips

Philips MONCARD Bedienungsanleitung

Alcatel

Alcatel onetouch v100 Bedienungsanleitung

Flow

Flow 836 ONT Bedienungsanleitung

AIRIS

AIRIS G819 Bedienungsanleitung

Philips

Philips LC7.1E Bedienungsanleitung

Loewe

Loewe Digital Recorder + Bedienungsanleitung

Sceptre

Sceptre Stello Bedienungsanleitung

Philips

Philips Flavors 42FDF7013 Bedienungsanleitung

Goodmans

Goodmans GD11FVRSD32 Bedienungsanleitung

Philips

Philips Clon99-BKI Bedienungsanleitung

Serene

Serene TVDirect TV-95 Bedienungsanleitung