Midas V190 Bedienungsanleitung

Midas,

Klark Teknik Building,

Walter Nash Road,

Kidderminster.

Worcestershire.

DY11 7HJ.

England.

Tel:+44 1562 741515

Fax:+44 1562 745371

Email: [email protected]

Website: www.midasconsoles.com

OPERATORS MANUAL

MIDAS Verona Power Supply

DOC02-V190

Operators Manual

Issue 1.0 - February 2004

In line with the company’s policy of continual improvement, specifications and function may be

subject to change without notice. This Operators Manual was correct at the time of writing. E&OE.

Important Safety InstructionsImportant Safety Instructions

IEC-60065-Edn7-Midas

These symbols are internationally accepted symbols that warn of potential hazards with

electrical products.

The lightning flash with arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturers

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments / accessories specified by the manufacturer.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified personnel. Servicing is required when the apparatus is damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

AVIS:RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

DECLARATION OF CONFORMITY

We,

of, Klark Teknik Building, Walter Nash Road, Kidderminster, Worcestershire, DY11 7HJ.

Declare that a sample of the following product:-

to which this declaration refers, is in conformity with the following directives and/or standards:-

Klark Teknik Group (UK) Plc

Product Type Number Product Description Nominal Voltage (s) Current Freq

A Subsidiary of Telex Communications, Inc.

V190 External Linear 100V AC, 120V AC 4.3A, 3.7A 50/60Hz

Power Supply 220V AC, 240V AC 2.1A, 1.95A

Signed:............................ Date: 27th February, 2004

Name: Simon Harrison

Authority: Research and Development Director, Klark Teknik Group (UK) PLC

Attention!

Where applicable, the attention of the specifier, purchaser, installer or user is drawn to special limitations

of use which must be observed when these products are taken into service to maintain compliance with

the above directives. Details of these special measures and limitations to use are available on request

and are available in product manuals.

Klark Teknik Group (UK) Plc, Klark Teknik Building, Walter Nash Road,

Kidderminster. Worcs. DY11 7HJ. England

Tel:+44 1562 741515 Fax:+44 1562 745371

www.midasconsoles.com www.klarkteknik.com

Directive(s) Test Standard(s)

Generic Standard using EN55103 Limits and Methods

Class B Conduct Emissions EN55103

Class B Radiated Emissions EN55103

Fast Transient Bursts EN61000-4-4

Static Discharge EN61000-4-2

Electrical Safety EN60065:2002

UL60065-03

CAN/CSA60065-03

IEC60065-2001

Pending

Contents

Installation and Service 1

Connection and Operation 2

Using Multiple Power Supplies 3

Specifications 4

The V190 external power supply has been developed to be used soley with the Midas Verona Series of audio mixing

consoles.

All backed up by the standard Midas Three Year Warranty.

Please take the time to complete and return the registration card and, to obtain the best results with a minimum of

effort, also read this operators manual.

The V190 series power supply unit is a two unit nineteen inch (2U 19”) rack mounted power supply for use with the Midas

Verona series of consoles only.

Before installing the power supply, please ensure that the correct mains supply voltage is selected on the rear of the supply.

The mains inlet is provided via a single IEC type socket. A mains cables is supplied with the unit. Never, under any

circumstances, should the power supply be operated without it’s safety earth connection.

The V190 series power supply should be installed into a 19” rackmount enclosure. If the power supplies are not in a

permanent installation, the rackmount enclosure construction should take into account the weight of the supply to prevent

damage to either the power supply or enclosure while in transit.

The V190 power supply has a forced air cooling channel flowing from back to front. To maintain adequate ventilation to the

unit, the cooling channel must not be blocked or hindered and one unit (1U) should be left free between the top of the

power supply and any other equipment or the rack. The rackmount enclosure should allow adequate airflow to both the

front and back panels of the power supply.

If using a number of power supplies, one unit (1U) space should be left free above each supply.

Some interference may be noticed when the power supply is situated in close proximity to the Verona console. Moving the

power supply away from the console will rectify this problem.

The power supply may only be serviced by authorised personnel. Refer all servicing to a qualified, approved Midas service

agent.

Depending upon where the power supply is installed, the interior of the unit will become, over time, dirty and will require

cleaning.

The power supply should also be serviced if it is dropped, exposed to rain or moisture, liquid has been spilled into the supply

or if the unit ceases to function normally.

The inside of the power supply contains potentially lethal voltages and is capable of providing high currents. To reduce

the possibility of electric shock, do not open the cover to the power supply. High voltages are still present in the

supply, even when isolated from the mains.

Installation

Service

Air Flow

Interference

DO NOT REMOVE THE COVER

Operators Manual - 1Page

Installation and ServiceInstallation and Service

Low

DC Output / Link

Power

Mains 48V

++8V

_8V

PUSHPUSH

Front

Rear

BEFORE APPLYING MAINS.

CHECK VOLTAGE SELECTOR

100V/120V/220V/240V

FUSE: 5x20mm

T5A L250V

50-60Hz 520W

SUPPLY

VOLTAGE

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

DC Output / Link

MADE IN KIDDERMINSTER, ENGLAND

FOR CONTINUED PROTECTION AGAINST RISK OF

ATTENTION:

CAUTION:

FIRE REPLACE WITH THE SAME TYPE AND VALUE FUSE INDICATED.

REMPLACER PAR UN FUSIBLE DE MÊME TYPE

COMME INDIQUÉ.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

WARNING:

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

AVIS:

DC Output / Link

Pin6-

Shell -

0VL

Chassis

Pin1-

Pin2-

Pin3-

Pin4-

Pin5-

0VA

48V

_8V

+8V

PUSH

Connection

Operation

Before powering up the V190 power supply, connect either the front or rear power supply output to the power inlet socket

on the console.

The V190 power supply should be connected to the mains with the supplied IEC mains leads.

The V190 is a Linear power supply capable of operation where the nominal mains voltage is 100, 120,

220 or 240 VAC (50-60Hz). The correct mains supply voltage must be selected before applying mains

power to the unit.

To change the mains operation voltage, disconnect from the mains. Open the compartment above the

mains inlet connector with a flat bladed screw driver. Once open, you will see a drum with an operating

voltages printed on each face. Remove the drum, then turn the drum to the required voltage and return

o the holder. Press firmly and then close the compartment. Make sure that the correct voltage now

appears in the window of the compartment.

After connecting the V190 power supply to the console, switch on the power supply using the rocker switches on the front

panel. Power will be applied to the console.

The user may monitor the activity of each of the voltage rails using the LEDs on the front panel. Each LED will light to show

the rail is active. In addition, a Low Mains indicator is provided to alert the user to a mains undervoltage condition.

The V190 power supply provides:

+12 volts

18 volts

+ 48 volts

The power supply should only be connected to the console using the provided power connection cable. If, for any reason,

the power connection cable should become damaged, the cable should be serviced by an authorised Midas service agent

immediately or a Midas authorised replacement sought.

The V190 power supply is capable of providing high currents. A short-circuit on any of the voltage supply pins

of the power supply or connector will cause a high current to flow from the supply which could lead to damage both to the

supply and to connected equipment and also a risk of fire and severe burns to persons.

it t

The Midas V190 power supply MUST be earthed. The power supply should NEVER be used with the earth connection

removed. The mains inlet socket earth connection is a safety connection and should be connected to the mains earth

through the earth conductor in the provided mains lead.

To prevent the risk of fire, fuses should always be replaced with fuses of the same rating and type.

The internal operating temperature of the power supply could be sufficient to cause burns to persons. Do not open the

cover or attempt to remove or bypass the safety covers protecting the fan and cooling channel.

WARNING:

NOTE:

WARNING:

WARNING: HOT

Where multiple supplies are present, these should be switched on at the same time so that excessive

load is not applied to any single supply. Power supply linking information is shown on the next page.

Power

DC Output / Link

Pin6- 0VL

Pin1-

Pin2-

Pin3-

Pin4-

Pin5-

0VA

+8V

_8V

48V

PUSH

220VAC

Low

Mains 48V

++8V

_8V

Operators Manual - 2Page

Connection and OperationConnection and Operation

Using Multiple Power Supplies

Servicing and Maintenance

The number of power supplies shipped as standard with the Verona varies with the frame size as follows:

24 - 32 1 0

40 - 56 2 0

64 2 1

Where multiple supplies are present, these should be switched on at the same time so that excessive load is not applied to

any single supply.

The external power supply can be used on 24-56 channel frame sizes to add redundancy or replace the internal supplies.

Two external supplies would be required to replace the internal supplies of the 56 channel console and retain redundancy.

The external supply has a “daisy chain” facility (as shown below) allowing for a number of power supplies to be used

together adding redundancy to the system in the event of a power supply failing.

Connection 6 Pin Male XLR

Pin 1 0V Analogue

Pin 2 +18V Analogue

Pin 3 -18V Analogue

Pin 4 +12V Gooseneck Light

Pin 5 +48V Phantom

Pin 6 0V Gooseneck Light

Case Chassis

Under NO circumstances should the Venice series power supply be used with the Verona.

Only the MidasV190 Linear External Power Supply is approved for use with Verona consoles.

Both the Verona and the Midas V190 linear external power supply both contain potentially lethal voltages and should only

be serviced by authorised Midas service agents. In the event of malfunction, please refer servicing to qualified personnel.

Contact your Midas dealer for more information.

Channels Internal External

Operators Manual - 3Page

Using Multiple Power SuppliesUsing Multiple Power Supplies

to console

to subsequent supplies

Low

DC Output / Link

Power

Mains 48V

++8V

_8V

PUSHPUSH

Low

DC Output / Link

Power

Mains 48V

++8V

_8V

PUSHPUSH

BEFORE APPLYING MAINS.

CHECK VOLTAGE SELECTOR

100V/120V/220V/240V

FUSE: 5x20mm

T5A L250V

50-60Hz 520W

SUPPLY

VOLTAGE

THIS DEVICE COMPLIES WITH PART15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:

(1) THIS DEVICE MAYNOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

DC Output / Link

MADE IN KIDDERMINSTER, ENGLAND

FOR CONTINUED PROTECTION AGAINST RISK OF

ATTENTION:

CAUTION:

FIRE REPLACE WITH THE SAME TYPE AND VALUE FUSE INDICATED.

REMPLACER PARUN FUSIBLE DE MÊME TYPE

COMME INDIQUÉ.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER SERVICEABLE PARTSINSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

WARNING:

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

AVIS:

DC Output / Link

Pin6-

Shell -

0VL

Chassis

Pin1-

Pin2-

Pin3-

Pin4-

Pin5-

0VA

48V

_8V

+8V

PUSH

BEFORE APPLYING MAINS.

CHECK VOLTAGE SELECTOR

100V/120V/220V/240V

FUSE: 5x20mm

T5A L250V

50-60Hz 520W

SUPPLY

VOLTAGE

THIS DEVICE COMPLIES WITH PART15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:

(1) THIS DEVICE MAYNOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

DC Output / Link

MADE IN KIDDERMINSTER, ENGLAND

FOR CONTINUED PROTECTION AGAINST RISK OF

ATTENTION:

CAUTION:

FIRE REPLACE WITH THE SAME TYPE AND VALUE FUSE INDICATED.

REMPLACER PARUN FUSIBLE DE MÊME TYPE

COMME INDIQUÉ.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER SERVICEABLE PARTSINSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

WARNING:

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

AVIS:

DC Output / Link

Pin6-

Shell -

0VL

Chassis

Pin1-

Pin2-

Pin3-

Pin4-

Pin5-

0VA

48V

_8V

+8V

PUSH

Inhaltsverzeichnis

Andere Midas Stromversorgung Handbücher

Midas

Midas EPS 1200 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung