Midea KJR-120M(X4)/BGEF Montageanleitung

Installation and Owner’s Manual

WIRED REMOTE CONTROLLER

IMPORTANT NOTE:

Please read this manual carefully

before installing or operating your

wired remote controller. Make sure to

save this manual for future reference.

MODEL:

KJR-120M(X4)/BGEF KJR-120M(X4W)/BGEF

KJR-120M(X5)/BGEF KJR-120M(X5W)/BGEF

KJR-120M(X6)/BGEF KJR-120M(X6W)/BGEF

KJR-120M1(X4)/BGEF

This manual gives detailed description of the precautions

that should be brought to your attention during operation.

In order to ensure correct service of the wired controller

please read this manual carefully before using the unit.

For convenience of future reference, keep this manual

after reading it.

All the pictures in this manual are for explanation purpose

only. There may be slightly dierent from the wired remote

controller you purchased (depend on model). The actual

shape shall prevail.

1. Safety precaution

2. Installation accessory

3. Installation method

4. Specification

5. Feature and function of the wired controller

6. Name on the LCD of the wired controller

7. Name of button on the wired controller

8. Preparatory operation

9. Operation

10. Timer functions

11. Weekly Timer 1

12. Weekly Timer 2

13. Fault alarm handing

14.Technical indication and requirement

15.Queries and settings

16. Wireless control connection

..........................................................1

................................................... 2

........................................................4

................................................................12

................13

.....................14

......................15

.................................................16

....................................................................17

...........................................................28

..........................................................31

.........................................................37

..................................................44

........................44

..................................................45

.......................................50

Table of Contents

1. Safety precaution

Do not uninstall the unit randomly.

Random uninstalling may lead to abnormal operation,

heating or re of the air condition.

WARNING

Please entrust the distributor or professionals to install the unit.

Installation by other persons may lead to imperfect installation,

electric shock or re.

Adhere to this installation manual.

Imporper installation may lead to electric shock or re.

Reinstallation must be performed by professionals.

•

NOTE

Do not install the unit in a place vulnerable to leakage of

ammable gases.Once ammable gases are leaked and left

around the wire controller, re may occure.

Do not operate with wet hands or let water enter the wire

controller. Otherwise, electric shock may occur.

•

The wiring should adapt to the wire controller current.

Otherwise, electric leakage or heating may occur and result in

re.

•

1. Safety precaution

NOTE

The specied cables shall be applied in the wiring. No external

force may be applied to the terminal. Otherwise, wire cut and

heating may occur and result in re.

•

2. Installation accessory

Don’t install at the place where cover with heavy oil, vapor or

sulfureted gas, otherwise, this product would be deformed

that would lead to system malfunction.

Select the installation location

Preparation before installation

1. Please conrm that all the following parts you have been supply.

M3.9*25 (For Mounting on the Wall)

M4X25 (For Mounting on switch box)

No. Name Qty. Remarks

Wire controller

Installation and owner’s manual

For Mounting on the Wall

Plastic screw bars

Screws

Wall plugs

For fixing on switch box

Optional

Screws

9Screw

Battery

The connective wires group

M4X8(For Mounting the connective wire group)

2. Installation accessory

Precaution of installingthe wire controller

1. This manual provides the installation method of wired

controller. Please refer to the wiring diagram of this installation

manual to connect the wire controller with indoor unit.

2. The wired controller works in low voltage loop circuit.

Forbid to directly contact the cable of high voltage above,

like 115V,220V,380V, and don’t wire this kind of wire in the

said loop; wiring clearance between congured tubes should

be at the range of 300~500mm or above.

3. The Shielded wire of the wired controller must be grounded

rmly.

4. Upon nish the wire controller connection, do not employed

tramegger to detect the insulation.

2. Prepare the following assemblies on the site.

Switch box

Wiring Tube(Insulating

Sleeve and Tightening

Screw)

Qty.(embeded

into wall)

No. Name Remarks

Specication

(only for reference)

3. Installation method

Fig 3-2

Fig 3-1

1.Wired remote controller structural dimensions

2.Remove the upper part of wired controller

Insert a slot screwdriver into the

slots in the lower part of the wired

controller (2 places), and remove

the upper part of the wire controller.

(Fig.3-2)

19mm84mm

46mm

60mm

44mm

120mm

Back cover

NOTE: Do not pry up and down, you can only rotate the

screwdriver.

Buckling

position

20mm

3. Installation method

Fig 3-3

Fig 3-4

For exposed mounting, fasten the back plate on the wall with the

3 screws (ST3.9*25) and plugs. (Fig.3-3)

Use two M4X25 screws to install the back cover on the 86 switch box,

and use one ST3.9*25 screw to x to the wall.

3. Fasten the back plate of the wired controller

Back plate

Screws (ST3.9*25)

Screw hole xed on the wall,useone ST3.9*25mm

Screw hole installed on 86 switch box, use two M4X25mm

NOTE: The PCB is mounted in the upper part of the wired

controller. Be careful not to damage the board with the

slot screwdriver.

3. Installation method

Put the battery into the installationsite and make sure the positive side

of the battery is in accordance with the positive side of installationsite.

(See Fig.3-5)

Please set the time corrected on the rst time operation. Batteries in

the wire controller can time under power failure which ensure the

time keep right. When the power restores, if the time displayed is not

correct, it means the battery is dead and replace the battery.

Fig 3-5

4. Battery installation

NOTE: Put on a at surface. Be careful not to distort the

back plate of the wire controller by overtightening the

mounting screws.

3. Installation method

Fig 3-6

5. Wire with the indoor unit

44mm

60mm

Wiring

hole

switch box

44mm

60mm

Wiring

hole

switch box

Model A

Model B

HA HB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Midea Controller Handbücher

Midea

Midea KJR-120G1/TFBG-E Montageanleitung

Midea

Midea KJR-120C/TF-E Betriebsanleitung

Midea

Midea KJRH-120H / BMKO-E Bedienungsanleitung

Midea

Midea KJR-29B/BK-E Bedienungsanleitung

Midea

Midea CCM-270A/WS Bedienungsanleitung

Midea

Midea KJR-29B/BKE-E Bedienungsanleitung

Midea

Midea KSACN0401AAA Bedienungsanleitung

Midea

Midea CCM30/BKE-A Bedienungsanleitung

Midea

Midea KJR-12B/DP(T) Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch