Midea GS-120D Bedienungsanleitung
GS-120D
Garment Steamer
Use’s Manual
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.
Safety Cautions
1
Before use, please read the instruction manual completely, and use the appliance
in accordance with the requirements to avoid any damage to persons or properties.
Never use this appliance for any purpose other than ironing clothes.
Never use other high-power electric appliance on the same socket to
avoid overload of circuits.
Never dismantle this appliance on your own. Any person
other than
qualified personnel shall not dismantle and repair the appliance, and
otherwise it may cause fire, electric shock or personal injury.
Before switching on the garment steamer, please check
the plug and
power cord carefully, and in case of damage, never use them.
Replacement must be
conducted by the manufacturer or its repair
department
or similar professionals to avoid danger.
Before inserting or pulling out the plug, be sure to switch
off the appliance.
When inserting or pulling out the plug, be sure to hold
the plug with
a hand, and never pull the power cord or
operate with a wet hand.
Before adding water, be sure to switch off first.
Please send the product to the
authorised agent for repair.
Before operation of the garment steamer, make sure that supporting
surface is even and secure to prevent
the garment steamer from
overturning or water from overflowing.
Do not heat the garment steamer when the water tank has not been
placed properly or water level is not enough.
Never add perfume, vinegar
, detergents or other chemicals into the water
tank. Otherwise they will stain the clothes and damage the garment
steamer.
All appliances in the product must be placed beyond the
reach of children
or the disabled to prevent any danger such as electric shock and
scratch. During operation of the garment steamer, the user shall not
leave.
WARNING
When the garment steamer is operating, do not point the steaming
nozzle at people.
2
Safety Cautions
WARNING
When the garment steamer is operating, its steaming nozzle, steam
supply hose and hose joint will become very hot. Do not, never touch
them so as to avoid scalding.
When the garment steamer is operating, never have the power cord in
touch with hot surfaces of the appliance, such as the steam supply hose
steamer head.
When the garment steamer is operating, never bend or wind the steam
supply hose.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Care should be taken when using the appliance due to the emission of
high temperature steam;
Unplug the appliance during filling and cleaning.
If the appliance or power cord is damaged, it must be replaced by
manufacturer or its service agent or a similarly qualified person in order
to avoid a hazard.
Never use the garment steamer on clothings with poor heat resistance
(such as for clothing), as the high temperature steam produce by the
steamer may cause deformation and discolouration to the clothing.
when the garment steamer is operating, NEVER touch the steaming
nozzle nor attach/ remove any accessories to the steamer head so as
to prevent any scalding injuries.
Parts Descriptions
Safety Cautions
CAUTIONS
When moving the appliance, hold the appliance body for movement.
Never drag the appliance by pulling the power cord.
To store the appliance, make sure that the garment
steamer has cooled
down, and water has been discharged
from the
machine.
Never immerse the appliance in water or any other liquid,nor rinse it
under the tap.
To prevent the hose from forming a U-shape,always place the steamer
on the floor to ensure that the hose is straight. If you hear an excessive
croaking sound or if the steam output is irregular, lift the steamer head
/
ironing head
from time to time to straighten the hose. This will allows
any condensation to flow back into the water tank.
After use, please turn off the switch, and pull out the plug.During draining
of water or cleaning, be sure to switch off, and keep the garment steamer
to cool down for at least 10min to avoid scalding by hot water.
3
3
Steamer head
steamer head and hanger holder
Cothes clamp
Clothes rail assembly
steam supply hose
Support rod
Locking spanner
Water tank
Parts Descriptions
Installation Instructions
(The schematic above is for reference only, the actual product may vary slightly.)
Seam clamp Brush Ironing board Glove
Usage Tips:
It is recommended to use purified water or filtered water, which makes
the Garment Steamer more durable. Clean regularly to avoid damaging of clothing by the
impurities in the water after long use.
Warning:
The appliance shall be used in an environment with temperature of
10-40℃and relative humidity of less than 90%.
4
Installation of support rod
1
Drain plug
Insert
Insert
Insert
Place the holder on the clothes rail
assembly (as shown), and press down
firmly to clip it into position.
Release the lock button,
insert the support rod into the
mainframe, and lock each spanner.
Install each part in sequence
according to the figure.
1
Installation Instructions
2.Rotate the fastener clockwise,
and lock by aligning the arrow
with the“ ” .
Installation of Steam Supply Hose
1.Align the arrow of the hose
fastener with the “ ”and
insert it in end.
5
2
Installed
dismantled
Place the brush top end on the upper
edge of steamer head, and fasten the
brush when the steamer head is aligned
with the boss of brush lower edge.
Dismantle in reverse order after use.
Place the clamp top end on the upper
edge of steamer head, with lower boss
snapped below.
Dismantle in reverse order after use.
Installed
dismantled
3 4
Installation of brush Installation of seam clamp
1.Hang up the clothes
2. Fill the water tank. 3.Put the tank back,
and start the machine.
6
Instructions
Preparations
1
1. Rotate the knob clockwise, and start the machine.
2.Choose different steam strength by adjusting the knob.
3.The stream reaches maximum on “3” and minimum on “1”.
2Konb-operated control
(The schematic above is for reference only, the actual product may vary slightly.)
7
Method
General application
Wear gloves or glove boards to
prevent from being scalded.
Ironing board can be used as an
auxiliary tool for ironing corners
such as collars, cuffs.
A brush can be used for removing
the fluffing.
Usage tips: Do not iron one place for a long time, so as not to damage the clothes.
(The schematic above is for reference only, the actual product may vary slightly.)
8
Ironing of trousers
Use the clothes clamp to aid
the ironing of trousers
Fix the trousers axis by setting
the seam clamp, press the
spanner, and iron from the top
to downwards.
Usage tips: Avoid overbending
or U-shaping the steam duct
during operation.
Method
9
Basic parameters
358X293X1600mm
Dimensions
GS-120D
Product nameGarment steamer
220-240V~
1500-1785W
2.0L
Model
power
Water tank capacity
Weight
voltage
6.0kg
frequency
50/60Hz
Safety Features
1. Temperature detection sensor: The Garment Steamer is equipped with
a built-in temperature sensing element. When there is abnormal temperature,
the temperature sensing element will emit signals to control the connection
and disconnection of the heating element, thus keeping the product
temperature within a suitable range.
2. Thermal fuse protection: The garment steamer has a thermal fuse installed.
When the temperature is abnormal and the thermostat fails, it switches off
directly to avoid any accident.
Maintenance and Storage
1. Turn the knob to “OFF” to switch off the garment steamer.
3. After cooling the product for 30 minutes, open the water tank cover, lift and tilt the
product, and pour out the water inside the product from the water tank cover.
4. Unscrew the drain plug counter-clockwise, the water in the principal machine will
flow out from the drain plug. (Note: Clear the accessories of the product before
unscrewing the drain plug in case the water flows out of the principal machine and
gets the accessories wet.)
5. After using the product for a long time, it is recommened to clean off the water scale
regularly to avoid impurities within the water staining the clothing; disassemble the
steam supply tube from the main body and fill the water into water inlet and shake the
machine. Then drain out the dirty water via the drainage hole.
The performance of the steamer will be better when repeating the above steps.
6. After winding the power cord and air duct, put the product in a dry place.
2. Disconnect the power plug.
Inhaltsverzeichnis
Sprachen:
Andere Midea Dampfreiniger Handbücher
