Midland X-TALKER T77VP5J Bedienungsanleitung

Model T70 Series

Page 2 midlandusa.com

Welcome to the world of Midland electronics

Congratulations on the purchase of your high quality MIDLAND

product. Your two-way radio represents state-of-the-art high-tech

engineering and is designed for FRS (Family Radio Service)

operation. It is a quality piece of electronic equipment, skillfully

constructed with the finest components. The circuitry is all solid-state

and mounted on a rugged printed circuit board. Your two-way radio is

designed for reliable and trouble-free performance for years to come.

Features

- 36 FRS Channels

- 121 Privacy Codes (38 CTCSS / 83 DCS)

- VOX

- 5 Selectable Call Alerts (5 additional Animal Sounds on T75)

- Vibrate Alert (T75 only)

- NOAA Weather Scan

- NOAA Weather Radio

- NOAA Weather Alert

- Scan Function

- Monitor Function

- Roger Beep Tone

- Silent Operation

- Key Pad Lock

- High / Low Power Settings

- Speaker / Microphone Jacks

- Battery Meter / Battery Low Indicator

- USB Jack Charging

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device does not cause harmful

interference, and (2) this radio must accept any interference that may

cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for body-worn

operation, this radio has been tested and meets the FCC RF exposure

guidelines when used with Midland Radio Corp. accessories supplied or

designated for this product. Use of other accessories may not ensure

compliance with FCC RF exposure guidelines.

Model T70 Series

Page 3 midlandusa.com

IMPORTANT NOTICE

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human

beings to radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999

Edition

- National Council on Radiation Protection and Measurements (NCRP) of

the United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection

(ICNIRP) 1998

To control your exposure and ensure compliance with the general

population or uncontrolled environment exposure limits, transmit no more

than 50% of the time. The radio generates measurable RF energy

exposure only when transmitting.

Body-Worn Operation

If you wear the radio on your body when transmitting always use Midland-

supplied or approved belt clip, holster, case, or body harness for this

product. Use of any accessories not supplied or approved by Midland may

exceed FCC/Health Canada RF exposure guidelines. If you do not use

any accessories supplied or approved by Midland, ensure the radio and

its antenna are at least 1 inch (2.5cm) from your body when

transmitting.

Model T70 Series

Page 4 midlandusa.com

LCD DISPLAY

1. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L).

2. NOAA WEATHER (WX) BAND ICON –

Indicates when the radio is in Weather

Band mode.

3. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

4. VOX ICON – Indicates when VOX mode

is active.

5. CHANNEL NUMBER – Changes from

1~36 on FRS band (1~10 on WX band).

6. VIBRATE ALERT ICON – Indicates when

the Vibrate-Alert feature is on (Model T75

only).

7. BATTERY METER – Indicates the battery

level.

8. RECEIVE (RX) ICON – Indicates radio is

receiving a transmission.

9. TRANSMIT (TX) ICON – Indicates radio

is transmitting a signal.

10. PRIVACY CODE ICON – Indicates

Privacy Code setting (CTCSS/DCS).

11. PRIVACY CODE – Indicates Privacy

Code selected by user (oF~38/oF~83). It

can only be set in Ch 1~22.

CONTROLS

12. POWER/VOLUME KNOB – Turn clock-

wise to turn the power on and increase

the volume level. Turn counter-clockwise

to decrease the volume level and turn

the power off.

13. PTT Button – Press and hold to

transmit voice communication.

14. CALL/LOCK Button – Press to send a

CALL ALERT signal. Press and hold to

turn KEY LOCK on/off.

15. MIC – Built-in microphone.

16. USB CHARGING JACK

17. ANTENNA

18. EXTERNAL SPEAKER/MIC JACK

19. MENU Button – Press momentarily to

access Menu mode.

20. MONITOR/SCAN Button – Press to

enter SCAN mode. Press and hold to

enter MONITOR mode.

21. UP/WX SCAN sand DOWN t

Buttons – Make adjustments in MENU

mode. Press and hold the UP button for

5 seconds to activate the NOAA

Weather Scan function.

22. SPEAKER – Built-in speaker.

Model T70 Series

Page 5 midlandusa.com

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 3 AA

alkaline batteries. The belt clip should be removed (see below) to

ease installation or removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram below) for easy access, then remove the Battery Cover by

pressing down on the top center and sliding it down from the radio.

2. Insert NiMH battery pack or 3 AA batteries observing the polarity

as shown. Installing the batteries incorrectly will prevent the unit

from operating or may damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip down into the slot on the back

of the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, pull the LOCK TAB away from the radio, then gently pull the

belt clip up toward the top of the radio.

Model T70 Series

Page 6 midlandusa.com

Your radios are equipped for using a rechargeable NiMH battery pack

(BATT10) which can be recharged by inserting one end of the USB

Cable into a USB power source, and the other end into the radio USB

charging jack, or with the optional desktop charger (as described

below). While charging, the Battery Meter will flash from 1 to 3 bars.

The LCD display will show FULL when charging is complete. For

maximum battery life, Midland recommends charging the battery

pack when the low battery icon comes on. Remove the radios from

the charger when the charging is finished.

To charge using the Desktop Charger:

1. Place the BATT10 rechargeable battery packs in the radios.

2. Connect one end of the USB Cable into a USB power source.

3. Insert the other end of the USB Cable into the desktop charger

USB jack.

4. Place the radios into the desktop charger slot. While charging, the

Battery Meter will flash from 1 to 3 bars, and stop when charging

is finished. The LCD display will show FULL.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged with the radio

turned OFF.

1. Only use the Midland NiMH battery pack.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the

manual. This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

BATTERY LEVEL INDICATOR

Your radio has a BATTERY LEVEL METER that shows the

battery power level. The greater the number of bars visible, the

stronger the battery level. When the battery level is low, the Battery

Shell icon and “bt Lo” will flash in the display indicating your

batteries should be replaced or recharged if using a rechargeable

battery pack.

CHARGING THE BATTERY PACK

Model T70 Series

Page 7 midlandusa.com

POWER ON/OFF AND VOLUME

Rotate the POWER/VOLUME knob clockwise to turn the radio on

and increase the volume level. Rotate the control counter-clockwise

to reduce the volume level and to turn the radio off. During Power On,

the radio will beep 2 times with different tones, the LCD will display all

icons for 1 second and the LCD display will indicate the last channel

selected.

RESTORING YOUR RADIO TO THE ORIGINAL SETTING

To reset your radio to the original (default) setting, turn on the radio

while pressing and holding the sbutton. The LCD display will briefly

show the firmware version number and then reset to standby mode

on channel 1 with no Privacy Code.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel and/or Privacy Code.

1. For maximum clarity, hold the radio at least 1 inch (2.5 cm) from

your mouth.

2. Press and hold the PTT button and speak in a normal voice into

the microphone. The TX icon will appear continuously on the

LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

ABOUT RANGE

Your radios are designed to give you maximum range under optimum

conditions.

OPERATING YOUR RADIO

Model T70 Series

Page 8 midlandusa.com

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure to set your radio to use Hi power.

T70 SERIES QUICK REFERENCE CHART

MONITOR

Pressing and holding the MONITOR button for 3 seconds will let you

hear noise so you can adjust the volume level of the radio when not

receiving a signal. This could also be used to check any activity on

your current channel before transmitting.

Press and hold the MONITOR button for 3 seconds again to get out

of MONITOR mode.

SCAN

Your radio can scan all 36 channels for activity. To enter, quickly press

the SCAN button. Repeat the same procedure to exit. Your radio will

rapidly scan each of the 36 channels and stop on any active channel

for 6 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel VOX

1~36

Privacy

Roger Beep

On/Off

Power

H/L

Call Alert

1~5

WX Channel

1~10

Silent Operation

On/Off

oF/1/2/3

CTCSS

DCS

1~38

1~83

WX Alert

On/Off

WX Scan

1~10

Press and hold UP/WX

button for 5 seconds

1~10 for T75

Vibrate

On/Off

T75 only

Model T70 Series

Page 9 midlandusa.com

CALL ALERT

Your radio can transmit a call alert. To send a call alert, press the

CALL button. The TX icon will appear while transmitting a call alert

and a tone can be heard on the speaker for confirmation. The T71

radio has 5 call alert selections while the T75 has 10 call alerts

including 5 “animal sound” call alerts - Cougar, Duck, Crow, Wolf,

and Turkey.

KEYPAD LOCK

To avoid accidentally changing the radio setting, press the LOCK

button for 4 seconds. The icon will appear on the display. PTT and

CALL will still be active. Repeat the same procedure to unlock the

keypad.

CHANNEL SELECTION (FRS BAND)

Press the MENU button once, and then the s\tbuttons to select

one of the 36 FRS channels. To confirm the selection, press the PTT

button or press the MENU button again to move to the next feature

setting.

SETTING PRIVACY CODES

Your radio has 121 Privacy Codes available. The selected Privacy

Code may be different for each channel. To select a Privacy Code

for the current channel press the MENU button twice, and then the

s\t buttons to select between Off/CTCSS/DCS. Press the MENU

button again and the s\tbuttons to select one of the 38 CTCSS

Codes or one of the 83 DCS Codes. The Privacy Code icon on the

display will indicate whether you set your Privacy Code in CTCSS or

DCS mode. To confirm the selection, press the PTT button or press

the MENU button again to move to the next feature setting.

Note : If you select a CTCSS Privacy Code, any pre-selected

DCS Privacy Code will be cancelled and vice-versa.

Selecting a Privacy Code of "oF"will disable the Privacy feature.

To communicate between two radios, all radios in your group

must be set to the same channel and/or Privacy Code selections.

The Privacy Code can only be set in channels 1~22.

Model T70 Series

Page 10 midlandusa.com

TRANSMIT (TX) POWER LEVEL SELECTION

Your radio has 2 power level settings. To select the power level on

channels 1~7 and 15~36, press the MENU button until a “Pr” icon will

appear blinking on the display. Then press the s\tbuttons to select

TRANSMIT POWER LEVEL icon (H: Hi/L: Lo). To confirm, press the

PTT button or press the MENU button again to move to the next

feature setting. When the PTT button is pressed during Lo Battery

Level condition, the TX Power will automatically switch from

Hi(H) to Lo(L) level.

Note : You cannot adjust the power setting on channels

8~14. They are set to Lo power per FCC regulations.

VOX

Your radio has 9 VOX level settings: (oF/1~9).

To set VOX, press the MENU button until the display shows “VOX” .

On the right of the CHANNEL NUMBER display, an “oF” icon

appears. Select “1” ~ “9” by pressing the s\tbuttons and push the

PTT key, or press the MENU button again to move to the next feature

setting. VOX will be more sensitive on the lower setting than on the

higher setting.

To turn VOX off, press the MENU button until the display shows

“VOX”. On the right of the CHANNEL NUMBER display, a “1” ~ “9”

icon appears. Select “oF” by pressing the s\tbuttons and push the

PTT key, or press the MENU button again to move to the next feature

setting.

ROGER BEEP (end of transmission) TONE

When the PTT button is released, the radio will beep to confirm to

other users that your transmission has finished.

To set the ROGER BEEP tone, press the MENU button until the

display shows an “rb” icon. Select “on” or “oF” by pressing the s\t

buttons and push the PTT key, or press the MENU button to move to

the next feature setting.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Midland Zwei-Wege-Funkgerät Handbücher

Midland

Midland XT-60 Handbuch

Midland

Midland X-Talker T10 Bedienungsanleitung

Midland

Midland GXT850 Series Bedienungsanleitung

Midland

Midland GXT-250 Bedienungsanleitung

Midland

Midland BR777 Handbuch

Midland

Midland MXT400 Bedienungsanleitung

Midland

Midland X-Tra Talk LXT600 Series Bedienungsanleitung

Midland

Midland LXT600 Series Bedienungsanleitung

Midland

Midland X-Tra Talk GXT740 Series Bedienungsanleitung

Midland

Midland G9 Bedienungsanleitung

Midland

Midland FG-2 Bedienungsanleitung

Midland

Midland LXT114VP Bedienungsanleitung

Midland

Midland ALAN 95 D80 PLUS Bedienungsanleitung

Midland

Midland x-talker t70 series Bedienungsanleitung

Midland

Midland ProLine PL5161 Bedienungsanleitung

Midland

Midland X-tra talk LXT560 series Bedienungsanleitung

Midland

Midland G9 Handbuch

Midland

Midland MICRO MOBILE MXT115V Bedienungsanleitung

Midland

Midland X-Tra Talk LXT360 Series Bedienungsanleitung

Midland

Midland x-talker t70 series Bedienungsanleitung

Midland

Midland BIZTALK MB400 Bedienungsanleitung

Midland

Midland GXT860 series Bedienungsanleitung

Midland

Midland EX37 Bedienungsanleitung

Midland

Midland GXT720 Series Bedienungsanleitung

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung

Motorola

Motorola DTR410 - On-Site Digital Radio Betriebsanleitung

Motorola

Motorola PRO7550 Bedienungsanleitung