Midland XT-10 Handbuch

* Depending on terrain

› Instruction guide

XT·10

WALKIETALKIE PMR446

4Km*

up to

2 | XT10 instruction guide

XT10 instruction guide | 3

Main functions

• Frequency: 446.00625 – 446.09375

• Channels: 16 (8+8 pre-programmed)

• 38 CTCSS tones

• Power: 500mW ERP

• Vox function

• Alphanumeric LCD Display

• CALL tone

• Scan function

• Operating temperature -20° to +55°

• Weight: 73 gr

• Dimensions: 85x30x48mm

• Category: B

What’s in the box

• 2 x XT10 transceivers

• 2 belt clips

Coverage

The maximum range depends on terrain condition and is obtained during use

in an open space.

The only limitation to maximum possible range are environmental factors such

as blockage caused by trees, buildings, or other obstructions. Inside a car or

a metallic constructions, the range can be reduced. In open space, without

obstructions and in sight, like for example in mountain, the coverage can reach

4 Km.

4 | XT10 instruction guide

Above all….Safety!

Warnings

! Do not open the radio for any reason! The radio’s precision mechanics and

electronics require experience and specialized equipment; for the same re-

ason, the radio should under no circumstances be realigned as it has alrea-

dy been calibrated for maximum performance. Unauthorized opening of the

transceiver will void the warranty.

! Do not use detergents, alcohol, solvents, or abrasives to clean the equipment.

Just use a soft, clean cloth. If the radio is very dirty, slightly dampen the cloth

with a mixture of water and a neutral soap.

XT10 instruction guide | 5

CALL

MON

SCAN

XT10

PTT

CALL

MON

SCAN

XT30

PTT

MIC SPK

2 3 4

Description of the controls and functions

CALL

MON

SCAN

XT10

PTT

CALL

MON

SCAN

XT30

PTT

MIC SPK

12 12

CALL

MON

SCAN

XT10

PTT

CALL

MON

SCAN

XT30

PTT

MIC SPK

6 | XT10 instruction guide

1. VOX function activated

2. Appears when the keypad lock is activated

3. Battery level

4. It is displayed when the radio is receiving a signal

5. Appears when the radio is transmitting (PTT pressed)

6. Indicates the selected CTCSS tone

7. Indicates the selected channel

8. Antenna

9. LCD Display

10. MON/SCAN. With this button you can enable/disable the Scan and

Monitor functions

11. MENU/ : Press this control to turn on/o the unit and to enter the ra-

dio’s menu.

12. ▲/▼: use these buttons to adjust the volume, select the channels and

functions

13. Microphone

14. Speaker

15. /CALL. Press this button to lock the keypad and to send out a call signal.

16. PTT button

17. Battery and battery compartment. The transceiver accepts 3 x AAA

alkaline/rechargeable batteries. To open the battery compartment, hold

the unit face down and slide the cover.

XT10 instruction guide | 7

Let’s communicate!

To turn on/o the radio

Hold down MENU/ for 3 seconds.

Channel selection

Press once the Menu button and then select the desired channel by the ▲/▼

buttons. Press PTT to conﬁrm the selection. Remember that both radios must

be set on the same channel.

Transmission

Keep pressed the PTT button. “Tx” and “to” will blink on the display. Release the

PTT and the radio beeps to conﬁrm to other users that your transmission has

ﬁnished ( ‘Roger Beep’, see paragraph).

Reception

Simply release the PTT button. When you receive a signal “Rx” is displayed.

Volume adjustment

Press the ▲/▼ to adjust the volume at the desired level.

button / CALL function

Keypad lock

This feature is very useful to avoid accidental pressure of the buttons. Press and

hold the “ /CALL” button for more than 3 seconds. The conﬁrms that the

keypad lock is activated. Only PTT and the long pressure of Menu will still be

active. Repeat the same procedure to unlock the keypad.

Sending an audio signal (CALL)

By pressing /CALL, you will send an audio signal to other users on the same

channel.

8 | XT10 instruction guide

Menu button

The following functions can be selected by pressing the Menu button:

• VOX

• Roger Beep on/o

• Channel setting

• CTCSS tone setting

• Keypad Beep on/o

VOX function

The VOX function lets you open the transmission by voice without the use of

the PTT button.

Push the Menu button for three times; “VOX” will be displayed and ‘oF’ will

blink. Select ‘on’ by means of the ▲/▼ buttons and then press the PTT button

to conﬁrm.

To disable the VOX mode

Press the Menu button for three times. “On” blinks on the display. Select ‘OF’

by means of the ▲/▼ buttons and then push PTT to conﬁrm.

Roger Beep: End transmission tone

When the PTT is released the radio will beep to conﬁrm to other users that

your transmission is ﬁnished. This feature is enabled by default.

To disable it:

1. Press the Menu button till the display shows “rb on”

2. Select “oF” by means of the ▲/▼ buttons.

3. Conﬁrm your selection by pushing the PTT button.

Channel setting

Press once the Menu button and then select the desired channel by the ▲/▼

buttons. Press PTT to conﬁrm the selection.

XT10 instruction guide | 9

CTCSS sub-audio tone setting

The CTCSS sub-tones, are code numbers (from 1 to 38) that can be added to

the ﬁrst 8 channels in order to create a new private channel. You can add up

to 38 codes to the channels named from P1 to P8. For example if you add the

CTCSS sub-tone “27” to the channel “P3” you will obtain the new channel

“P327” that will be able to communicate to other transceivers only if they will

be set on the same channel and sub tone.

To activate 38 dierent CTCSS sub-tones follow these steps:

1. Turn on the radio.

2. Press the Menu button and select with the ▲/▼ buttons one of the 8

channels (from P1 to P8).

3. Press twice the Menu button until the display shows the selected channel

with the ﬂashing two CTCSS sub-tone digits (on the right of the channel)

4. Select with the ▲/▼ buttons the desired CTCSS tone (from 1 to 38).

5. To conﬁrm the setting press PTT.

Now the radio transmits and receives using the programmed CTCSS sub-

tone. If you don’t want to use any CTCSS tone, select “oF”.

CTCSS tones displayed on the LCD

When you activate a CTCSS sub-tone, from P1 to P8, you can see the tone

on the right side of the channel. For the other channels (from 9 onwards) the

CTCSS sub-code is pre-programmed and then “hidden”.

Keypad beep o

Everytime you press any button, you will hear a beep sound. To deactivate it

press Menu 4 times. Then select “oF” with the ▲/▼ controls and conﬁrm your

selection by pushing PTT. To enable the beep again, repeat the same procedure

and select “ON”.

MON/SCAN

Monitor function

When this feature is activated, the radio can receive very low and weak signals.

This is very useful when you need to talk but the distance is as far as the ma-

ximum range possible; with the monitor feature you can extend the coverage

of the radio.

The disadvantage is the reception of loud background noises.

10 | XT10 instruction guide

Activation: Keep pressed MON/SCAN till the display shows “Rx”.

Deactivation: Do the same procedure or switch o the radio

SCAN function

The SCAN mode monitors the busy channels.

It is used to check the trac radio on all the channels before transmitting and

allows the unit to stop on a channel that someone is talking on. When the radio

stops on a busy channel, the scan will resume after about 5 seconds.

To activate the SCAN function

Push brieﬂy MON/SCAN.

To deactivate it:

Press MON/SCAN or PTT.

Automatic power save

XT10 is supplied with an automatic current economy circuit. If the transceiver

receives no signal for more than 10 seconds, the “power save function” auto-

matically activates. The battery life may increase by up to 50 %.

Inhaltsverzeichnis

Andere Midland Zwei-Wege-Funkgerät Handbücher

Midland

Midland Micro Mobile MXT105 Bedienungsanleitung

Midland

Midland XT511A Bedienungsanleitung

Midland

Midland GXT850 Series Bedienungsanleitung

Midland

Midland X-Tra Talk GXT1000 Series Bedienungsanleitung

Midland

Midland G11V Handbuch

Midland

Midland X-TRA TALK LXT110/80 Bedienungsanleitung

Midland

Midland 70-1526A/B Bedienungsanleitung

Midland

Midland MICROMOBILE MXT400VP3 Bedienungsanleitung

Midland

Midland G15 Bedienungsanleitung

Midland

Midland GXT-250 Bedienungsanleitung

Midland

Midland X-TRA TALK LXT110 Series Handbuch

Midland

Midland GXT710 Series Bedienungsanleitung

Midland

Midland LXT600 Series Bedienungsanleitung

Midland

Midland M-10 Bedienungsanleitung

Midland

Midland G9 Handbuch

Midland

Midland GXT2000 Series Bedienungsanleitung

Midland

Midland Alan 52 DS Bedienungsanleitung

Midland

Midland ALAN 95 D80 PLUS Bedienungsanleitung

Midland

Midland GXT 400 Series Bedienungsanleitung

Midland

Midland X-tra Talk LXT118 Series Bedienungsanleitung

Midland

Midland X-TRA TALK LXT380 Series Bedienungsanleitung

Midland

Midland GMRS/FRS Radio LXT112 Series Bedienungsanleitung

Midland

Midland XT-50 Handbuch

Midland

Midland GXT5000 Series Bedienungsanleitung

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung

Motorola

Motorola DTR410 - On-Site Digital Radio Betriebsanleitung

Motorola

Motorola PRO7550 Bedienungsanleitung