Miele GAS COMBISET CS 1011 Bedienungsanleitung

Converting Instructions

Instructions pour la conversion

CS 1011

CS 1012

CS 1028

M.-Nr. 07 369 750

en, fr - US, CA

®®

Converting CS 1011

Converting CS 1012

Converting CS 1028

Conversion à CS 1011

Conversion à CS 1012

Conversion à CS 1028

Contents

The cooktop should have been ordered

for connection to either natural or LP

(propane) gas.

The included regulator corresponds

with the gas type of the cooktop. Verify

before installing. See, "To convert the

regulator".

If the appliance is to be connected to a

type of gas other than it was originally

configured for, both the regulator and

burners must be converted.

,WARNING

The conversion kit must be

installed by a qualified technician

in accordance with the

manufacturer’s instructions and

all applicable local and national

codes. If the information in these

instructions is not followed

exactly, a fire, explosion or

production of carbon monoxide

may result causing property

damage, personal injury or loss of

life. The qualified technician is

responsible for the proper

installation of this kit. The

installation is not proper and

complete until the operation of the

converted appliance is checked as

specified in these instructions.

To convert the regulator:

^Unscrew the hexagonal nut (brass

cap) located on the top of the

regulator.

^Make sure that the spring stays in

place.

^Take the plastic insert out and flip it

over.

The plastic insert is marked on either

end:

- NAT (Natural Gas)

- LP (Propane)

^Set the plastic insert back into the

nut.

^Screw the hexagonal nut back on the

regulator.

Converting CS 1011

To convert the burner

,Conversion to a different type of

gas should only be performed by an

authorized gas technician.

Turn off the main gas supply (if the

appliance has been installed) and

disconnect the appliance from the

main electrical power supply before

proceeding.

When converting to a different type of

gas, the jets and needle valves have to

be changed.

Maximum output

Gas type BTU/hr kW

Natural Gas 17,500 5.2

LP Gas (Propane) 17,500 5.2

Minimum output

Gas type BTU/hr kW

Natural Gas 680 0.20

LP Gas (Propane) 680 0.20

The following jets and needle valves

should be installed into their respective

burners. Follow codes accordingly.

Code Jet size

(Ø mm)

Code Needle

valve

size

(Ø mm)

Natural gas

Outer/Large

burner

200 2.00 88 0.88

Inner/Small

burner

34 34 42 0.42

LP Gas (Propane)

Outer/Large

burner

120 1.20 54 0.54

Inner/Small

burner

7 7 25 0.25

Converting CS 1011

^Remove the burner grates, the small

burner cap o, the large burner cap

p, the burner ring qand the burner

base r.

^Pull off the control knob.

^Loosen the screws w.

^The combiset surface can now be

removed.

Changing the large burner jet

^Using a 10 mm wrench, remove the

jet. While doing this, use a 13 mm

wrench to hold the gas tube to

prevent it from twisting.

^Install the new jet using the same

procedure.

Converting CS 1011

Changing the small burner jet

a,cFittings

bConnector

dSmall burner jet

eAir sleeve

fAir vent

^First loosen the fitting, c, using an

8 mm wrench. While doing so hold

the connector, b,witha12mm

wrench to prevent the tubing from

twisting.

^Then remove the connector, b, from

the fitting, a, using two 12 mm

wrenches.

^Remove the jet, d, and replace it

with the new jet.

^Slide the air sleeve, e, until there is a

1/16" (2 mm) gap between the sleeve

and the air vent, f, as shown.

Reassemble the burners and test the

unit for leaks. The cooktop can be

operated without the cooktop surface in

place by igniting the flames with a

match.

Converting CS 1011

Check the intake air

aLock screw

bAir sleeve

Gap X must measure:

– ½" (13 mm) for natural gas

– ½" (13 mm) for LP (propane) gas

^To adjust the gap, loosen the lock

screw and slide the air sleeve in or

out as necessary.

^Tighten the lock screw.

^Use sealant to secure the jets and

prevent loosening.

^Reassemble the cooktop in reverse

order.

The flame must not go out on the lowest

setting, or when the control is turned

quickly from a high to a low setting.

On the highest setting the flame must

have a distinctive and visible core.

Changing the needle valves

aNeedle valve with small jet

bNeedle valve with large jet

^Using a small screwdriver, unscrew

the needle valves and remove them

with a pair of needle nose pliers.

^Insert the new valves and screw them

in place.

^Use sealant to secure the jets and

prevent loosening.

,Check all fittings for gas leaks

before reassembling the cooktop.

Converting CS 1011

After conversion

^After converting the cooktop, affix the

label supplied with the conversion kit

on to the data plate over the type of

gas stated.

^Reassemble the burner parts in the

reverse order.

^Check all gas fittings for leaks by

operating the burner without the

combiset surface in place (use a

match to ignite the flame).

^Remove the burner parts again.

^Replace the combiset surface.

^Screw the burner base into place,

and replace the other parts of the

burner. Take care to reassemble the

burner in the correct order.

^Replace the control knob.

^Light the burner to be sure it is

operating correctly.

When set at "low" or when the control

knob is quickly turned from "high" to low

the flame should not go out.

When set at "high" the gas flame must

burn with the center clearly visible.

Converting CS 1011

The cooktop should have been ordered

for connection to either natural or LP

(propane) gas.

The included regulator corresponds

with the gas type of the cooktop. Verify

before installing. See, "To convert the

regulator".

If the appliance is to be connected to a

type of gas other than it was originally

configured for, both the regulator and

burners must be converted.

,WARNING

The conversion kit must be

installed by a qualified technician

in accordance with the

manufacturer’s instructions and

all applicable local and national

codes. If the information in these

instructions is not followed

exactly, a fire, explosion or

production of carbon monoxide

may result causing property

damage, personal injury or loss of

life. The qualified technician is

responsible for the proper

installation of this kit. The

installation is not proper and

complete until the operation of the

converted appliance is checked as

specified in these instructions.

To convert the regulator

^Unscrew the hexagonal nut (brass

cap) located on the top of the

regulator.

^Make sure that the spring stays in

place.

^Take the plastic insert out and flip it

over.

The plastic insert is marked on either

end:

- NAT (Natural Gas)

- LP (Propane)

^Set the plastic insert back into the

nut.

^Screw the hexagonal nut back on the

regulator.

Converting CS 1012

To convert the burners

,Conversion to a different type of

gas should only be performed by an

authorized gas technician.

Turn off the main gas supply (if the

appliance has been installed) and

disconnect the appliance from the

main electrical power supply before

proceeding.

When converting to a different type of

gas, the jets and needle valves have to

be changed.

Maximum output

Gas type BTU/hr kW

Normal

burner

Natural Gas

LP Gas (Propane)

5,700

5,000

1,65

1.45

Fast

burner

Natural Gas

LP Gas (Propane)

10,600

9,300

3.10

2.75

Total

output

Natural Gas

LP Gas (Propane)

16,300

14,300

4.75

4.2

Minimum output

Gas type BTU/hr kW

Normal

burner

Natural Gas

LP Gas (Propane)

775

1,010

0.227

0.296

Fast

burner

Natural Gas

LP Gas (Propane)

1,550

1,500

0.454

0.439

The following jets and needle valves

should be installed into their respective

burners. Follow codes accordingly.

Code Jet size

(Ø mm)

Code Needle

valve size

(Ø mm)

Natural gas

Normal

burner

110 1.10 42 0.42

Fast

burner

150 1.50 60 0.60

LP Gas (Propane)

Normal

burner

68 0.68 29 0.29

Fast

burner

92 0.92 40 0.40

Converting CS 1012

Andere Handbücher für GAS COMBISET CS 1011

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Miele Kochfeld Handbücher

Miele

Miele KM6357 Bedienungsanleitung

Miele

Miele CS 1018 G Bedienungsanleitung

Miele

Miele KM 6320 Bedienungsanleitung

Miele

Miele KM 92-2 Bedienungsanleitung

Miele

Miele ProLine CS 1012-2 Bedienungsanleitung

Miele

Miele KM 5987 Bedienungsanleitung

Miele

Miele KM 5676 Benutzerhandbuch

Miele

Miele KM 2355 G Bedienungsanleitung

Miele

Miele KM 3034-1 Bedienungsanleitung

Miele

Miele HR 1124 Gebrauchs- und Pflegehandbuch

Miele

Miele KM 406 Bedienungsanleitung

Miele

Miele Gas cooktop Bedienungsanleitung

Miele

Miele KM 391 Bedienungsanleitung

Miele

Miele SmartLine Bedienungsanleitung

Miele

Miele KM 400 Bedienungsanleitung

Miele

Miele KM 320 Bedienungsanleitung

Miele

Miele KM 5773 Handbuch

Miele

Miele KM 320 Bedienungsanleitung

Miele

Miele MasterChef KM342 Bedienungsanleitung

Miele

Miele KM 5621 Stücklistenhandbuch

Miele

Miele KM 2354 Bedienungsanleitung

Miele

Miele KM 6324-1 Bedienungsanleitung

Miele

Miele KM 34 Series Handbuch

Miele

Miele KM 6381 Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung

KitchenAid

KitchenAid KGCP482KSS0 Bedienungsanleitung