Miele KM 360 Bedienungsanleitung

Installation Instructions

Gas cooktop

KM 360

To prevent accidents and

machine damage,

read these instructions

before installation or use.

M.-Nr. 06 390 460

®®

WARNING:

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

–Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

–WHAT TO DO IF YOU SMELL GAS

ßDo not try to light any appliance.

ßDo not touch any electrical switch.

ßDo not use any phone in your building.

ßImmediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

ßIf you cannot reach your gas supplier, call the

fire department.

– Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

(In Massachusetts a licensed plumber / gas fitter)

–Note to the installer:

Please leave this instruction book with the

consumer for the local electrical / gas inspector’s

use.

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setting the cooktop into place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Securing the cooktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gas pressure regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Converting to another type of gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contents

Installation

The minimum distances given in

these Installation instructions are to

combustible surfaces, and must be

observed to ensure safe operation.

Failure to do so increases the risk of

fire.

The cabinetry and venting hood

should be installed first, to prevent

damage to the cooktop.

Gas appliances should only be

installed in a well ventilated area.

The countertop must be bonded

with heat resistant (212°F/100°C)

adhesive to prevent distortion or

dissolving.

The cooktop should only be

installed as shown, while

maintaining the required safety

distances shown. Do not install the

cooktop between two tall cabinets, this

is a fire hazard.

a= minimum distance between the

cooktop and a tall cabinet:

12" (305 mm)

This equipment has not been

designed for maritime use or for

use in mobile installations such as

aircraft or recreational vehicles.

However, under certain circumstances

it may be possible for installation in

these applications. Please contact the

Miele Technical Service Department

with specific requirements.

recommended

not recommended

not allowed

IMPORTANT SAFETY INSTRUCTIONS

The cooktop must not be installed

over a dishwasher, washer, dryer,

refrigerator or freezer. Heat radiated by

the cooktop may damage them.

Deep fat fryers must not be

installed next to gas cooktops. Gas

flames can ignite splattering oil. A

distance of at least 12" (305 mm)

should be maintained between these

two appliances. The minimum distance

between two cooktops must be 4"

(100 mm).

Install the appliance so that the

power cord or gas piping does not

come into contact with any portion of

the cooktop which may become hot

during use.

This appliance must be installed

with its own shut off valve and the

included gas pressure regulator.

Both the valve and the regulator

must be easily accessible to the

consumer after the appliance is

installed.

This appliance must be

disconnected from the gas supply

during any pressure testing of the

system performed in excess of ½ psi

(3.5 kPa). This appliance must be

isolated at test pressures equal to or

less than ½ psi (3.5 kPa).

Any pipe connections must be made

using a thread sealant approved for

gas connections. Failure to correctly

install these items could lead to a

gas leak and subsequent explosion.

Safety distances above the

appliance

There must be a safety distance of at

least 30" (760 mm), bbetween the

appliance and any objects above it.

The overhead cabinet depth, c, if

unprotected, must not exceed 13"

(330 mm). The minimum distance of

combustible surfaces located above

and to the sides of the cooktop, d, is

18" (457 mm).

If the cabinet manufacturer

recommends a greater distance, follow

that manufacturers recommendation.

When installing the cooktop under a

venting hood, always observe the

minimum distance recommended by

the hood manufacturer.

Keep this instruction book in a safe

place for future reference and pass it

on to an future user.

IMPORTANT SAFETY INSTRUCTIONS

aBuilt in depth

bElectrical connection box

cGas connection R ½" NPT

^Rember to maintain the minimum safety distances to combustible surfaces:

- 2 3/4" (70 mm) between the cooktop and the back wall and

- 12" (305 mm) between the cooktop and a side wall or tall unit to the right or left

of the cooktop.

(See "Important Safety instructions").

Appliance dimensions

Setting the cooktop into place

^Screw the gas regulator onto the

nipple underneath the cooktop. For

convenience, an AGA or CGA

approved flexible stainless steel gas

hose (accordion type) may be used

between the gas connection and the

regulator. For more information see

"Gas connection - Gas pressure

regulator".

The included gas regulator must be

installed between the cooktop and

the gas shut off valve. If clearance

for the regulator does not exist

directly under the cooktop, it may be

moved closer to the shut off valve.

^Guide the power cord through the

cut-out.

^Set the cooktop in the cut-out and

center it.

Securing the cooktop

^Secure the cooktop in position with

the supplied fixing brackets, a.

The cooktop must not be

permanently sealed into the

countertop when installed.

The sealing strip under the edge of

the cooktop provides a sufficient

seal for the countertop.

If the cooktop is sealed into position,

the countertop or appliance may be

damaged if the cooktop needs to be

removed for maintenance or service.

Installation

This appliance must be electrically

grounded. All electrical work should

be performed by a qualified

electrician in accordance with local

or national codes and the:

- National Electrical Code

ANSI / NFPA No. 70

for the USA

- Canadian Electrical Code Part I

for Canada

(CSA Standard C 22.2

No. O-M91).

,WARNING

Disconnect the appliance from the

main power supply before

installation or service. To reduce the

risk of electric shock, make sure that

the appliance is properly grounded

after installation.

Power supply

The automatic ignition requires that the

cooktop be connected to a 120 VAC,

60 Hz power supply. The supply line

should be protected by a 15 A breaker.

Actual power consumption (during

ignition only) is 25 W.

This appliance is equipped with a 4 ft.

(1.2 m) long power cord that is ready

for connection to the appropriate outlet.

Please place the power outlet so that it

is accessible after the appliance has

been installed in the countertop.

This appliance is equipped with a

three-prong grounding plug to

prevent shock hazards. It should be

plugged directly into a properly

grounded outlet. Do not cut or

remove the grounding prong from

the plug. If the plug does not fit the

outlet, have a proper outlet installed

by a licensed electrician.

To guarantee the electrical safety of

this appliance, continuity must exist

between the appliance and an

effective grounding system. It is

imperative that this basic safety

requirement be met. If there is any

doubt, have the electrical system of

the house checked by a qualified

electrician.

The manufacturer cannot be held

responsible for damages caused by

the lack, or inadequacy, of an

effective grounding system.

Note to the installer

Please leave these instructions with the

consumer or the appliance.

Electrical connection

Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

In Massachusetts a licensed

plumber/gas fitter is required.

This appliance must be installed

with its own shut off valve and the

included gas pressure regulator.

Both the valve and the regulator

must be easily accessible to the

consumer to turn on or shut off the

gas supply after the appliance is

installed.

This appliance and its individual

shut off valve must be disconnected

from the gas supply during any

pressure testing of the system

performed in excess of 1/2psi

(3.5 kPa). The machine must be

isolated from the gas supply line by

closing its individual manual shut off

valve at test pressures equal to or

less than 1/2psi (3.5 kPa).

Any pipe connections must be made

using a thread sealant approved for

gas connections. Failure to correctly

install these items could lead to a

gas leak and subsequent explosion.

The gas connection must be made

in accordance with local codes or in

the absence of local codes with:

- the National Fuel Gas Code,

ANSI Z 21.1 for the USA

- the current Can / CGA

Interim #58-M95

and .2 Installation Codes for gas

burning appliances for Canada.

Make sure that the maximum gas

supply pressure, before the gas

pressure regulator, is never more than

1/2psi (3.5 kPa) for natural gas or LP

gas.

The minimum supply pressure to get

the required gas input is

6" w.c. for natural gas

10" w.c. for LP gas.

Gas connection

Gas pressure regulator

A pressure regulator that is convertible

from natural to LP gas (Propane) or vice

versa is included with the appliance.

The included regulator corresponds

with the gas type of the cooktop. Verify

before installing.

The adjusted pressure is:

natural gas - 4" w.c.

LP gas - 10" w.c.

aCooktop

b½" NPT

cRegulator

As shown in the above diagram, the

included regulator must be used when

connecting the Miele cooktop to your

gas supply. This item has been

customized by Miele to meet all

applicable safety requirements. Make

sure the regulator is easily accessible

for adjustment after the appliance has

been installed.

For convenience, an AGA or CGA

approved flexible stainless steel gas

hose (accordion type) may be used

between the gas connection and the

regulator. This will allow the appliance

to be lifted out of the countertop for

cleaning or servicing. Make sure that

any drawers, cabinet doors, etc., do not

rub on this gas hose.

Do not use any regulator unless it

has been supplied by Miele. Doing

so may cause a gas leak.

If there is any doubt concerning

installation contact the Miele Technical

Service Department:

U1-800-999-1360

[email protected]

V1-800-565-6435

[email protected]

After connecting the appliance check

all fittings for gas leaks e.g. with

soapy water.

When installed properly, the flame will

be steady and quiet. It will also have a

sharp, blue inner core that will vary in

length proportional to the burner size.

Flame adjustment will not be necessary.

Gas connection

Andere Handbücher für KM 360

Inhaltsverzeichnis

Andere Miele Kochfeld Handbücher

Miele

Miele KM 6366-1 Bedienungsanleitung

Miele

Miele KM 443 Bedienungsanleitung

Miele

Miele GAS COMBISET CS 1012 Bedienungsanleitung

Miele

Miele KM 3010 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Miele

Miele KM 5987 Bedienungsanleitung

Miele

Miele KM 406 Bedienungsanleitung

Miele

Miele CS 1028 Bedienungsanleitung

Miele

Miele MasterChef KM452 Bedienungsanleitung

Miele

Miele CS 1011 Bedienungsanleitung

Miele

Miele MasterChef KM421 Bedienungsanleitung

Miele

Miele KM 7678 FR Bedienungsanleitung

Miele

Miele CS 1221 Bedienungsanleitung

Miele

Miele ProLine CS 1212-1 Bedienungsanleitung

Miele

Miele GAS KM 81-2 Bedienungsanleitung

Miele

Miele KM 6317 Bedienungsanleitung

Miele

Miele KM 6325-1 Bedienungsanleitung

Miele

Miele KM 342 Bedienungsanleitung

Miele

Miele KM6357 Bedienungsanleitung

Miele

Miele KM 6388 Bedienungsanleitung

Miele

Miele KM 443 Bedienungsanleitung

Miele

Miele TX3587 Bedienungsanleitung

Miele

Miele KM 5676 Bedienungsanleitung

Miele

Miele KM 3474 Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Casselin

Casselin CSASRE24 Bedienungsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung