Miele FN 28262 edt/cs Bedienungsanleitung

11210610-01

Installation

*INSTALLATION*

Installation

Fire risk and danger of damage

from appliances which give off heat.

Appliances which give off heat can

catch fire and set fire to the

refrigeration appliance.

Do not place appliances which give

off heat, such as mini-ovens, double

burner hobs or toasters on the

refrigeration appliance.

Fire risk and danger of damage

from open flames!

Open flames can set fire to the

refrigeration appliance.

Keep open flames (e.g. a candle)

away from the refrigeration

appliance.

Side-by-side installation

Risk of damage due to

condensation on the external

appliance panels.

In environments with high humidity,

condensation can build up on

external appliance panels, which can

cause corrosion.

Do not place different refrigeration

appliance models directly next to

one another.

However, your appliance can be part of

a “side-by-side” installation because it

is equipped with built-in heating units in

the side panels.

Please contact Miele for information on

which combinations are suitable for

your appliance.

Location

This appliance should be installed in a

dry, well-ventilated room.

When deciding where to install your

appliance please bear in mind that it will

use more energy if installed near a

heater, cooktop or other appliance that

gives off heat. Direct sunlight should

also be avoided.

The higher the room temperature, the

longer the compressor will run and the

higher the energy consumption will be.

When installing the appliance, please

note:

- The mains socket must not be

located directly behind the appliance

and must be easily accessible.

- The plug and cable must not touch

the rear of the appliance as they

could be damaged by vibrations from

the appliance.

- Nor should other appliances be

plugged into a socket located directly

behind this appliance.

11210610-01

Installation

*INSTALLATION*

Risk of damage due to

condensation on the external

appliance panels.

In environments with high humidity,

condensation can build up on

external appliance panels, which can

cause corrosion.

To prevent this, it is advisable to

install the appliance with sufficient

ventilation in a dry and/or air

conditioned room.

After installation, make sure that the

appliance door closes properly, that

the specified ventilation gaps are

adhered to, and that the appliance

has been installed in accordance

with these installation instructions.

Climate range

This refrigeration appliance is designed

for use within specific ambient

temperatures (climate range). Do not

use in ambient temperatures for which it

is not designed.

A lower room temperature leads to the

compressor switching off for longer

periods. This can cause the internal

temperature in the appliance to rise with

the risk of food deteriorating and going

off.

The climate range is stated on the data

plate inside the appliance.

Climate range Ambient room

temperature

SN +10 to +32°C

N +16 to +32°C

ST +16 to +38°C

T +16 to +43°C

11210610-01

Installation

*INSTALLATION*

Ventilation

Risk of fire and damage due to

insufficient ventilation!

If the refrigeration appliance is not

ventilated sufficiently, the

compressor will run more frequently

and for longer periods. This will

result in increased energy

consumption and a higher operating

temperature of the compressor. This,

in turn, can result in damage to the

compressor.

Please ensure that there is adequate

ventilation around the refrigeration

appliance.

It is essential to observe the required

ventilation gaps. The ventilation gaps

must not be covered or blocked in

any way.

Air at the back of the appliance gets

warm.

Fitting the supplied wall spacers

The wall spacers supplied must be

used in order to achieve the stated

energy consumption values and to

prevent the build-up of condensation

at high ambient temperatures.

Appliance depth is increased by

approx. 35mm with the wall spacers

fitted. If the wall spacers are not used,

the functionality of the appliance is not

affected. However, energy

consumption is slightly increased with

less distance between the appliance

and the wall.

Fit the wall spacers onto the back of

the appliance on the top left and

right.

Installation

Two people are required for

installing the appliance.

The appliance must be empty

when it is installed.

Move the appliance carefully on

floors that are sensitive to scratching

to prevent damage.

11210610-01

Installation

*INSTALLATION*

For easier installation there are

transport handles on the back at the

top and transport wheels underneath

the appliance.

Prepare the appliance for installation

as close as possible to its intended

installation location.

Release the mains connection cable

from the back of the appliance.

Remove the cable clip from the back

of the appliance.

Move the appliance carefully to its

intended installation location.

Position the appliance with the wall

spacers (if used) or the back close to

the wall.

Supporting the appliance door

Risk of damage and danger of

injury due to the appliance door

swinging open or the refrigeration

appliance tipping over.

If the additional adjustable foot on

the lower hinge plate is not sitting

correctly on the floor, the appliance

door may swing open or the

refrigeration appliance may tip over.

Ensure that you unscrew the

adjustable foot with the supplied

spanner until it sits on the floor.

Then unscrew it by a further quarter

turn.

Installing the appliance in existing

kitchen units

Risk of fire and damage due to

insufficient ventilation!

If the appliance is not ventilated

sufficiently, the compressor will run

more frequently and for longer

periods. This will result in increased

energy consumption and a higher

operating temperature of the

compressor. This, in turn, can result

in damage to the compressor.

Please ensure that there is adequate

ventilation around the appliance.

It is essential to observe the required

ventilation gaps. The ventilation gaps

must not be covered or blocked in

any way.

11210610-01

Installation

*INSTALLATION*

aTop box

bAppliance

cHousing unit

dWall

x: The appliance depth is increased by

approx. 35 mm for appliances with

wall spacers fitted.

The appliance can be built into a run of

kitchen units and installed directly next

to a kitchen furniture unit. The front of

the appliance then protrudes 65 mm

(approx. 100 mm if wall spacers are

fitted) from the front of the adjacent

furniture unit.

This enables the doors to be opened

and shut without being obstructed. To

match the height of the kitchen units in

the run, the appliance can be fitted with

a suitable top box.

When installed next to a wall a

distance of at least 45mm must be

maintained on the hinge side between

the wall and the appliance.

The larger the ventilation gaps, the

more economically the compressor

will work.

- A ventilation gap of at least 50mm

depth must be provided at the back

of the appliance behind the whole

width of the top box for air to

circulate.

- The ventilation gap under the ceiling

must be at least 300cm2 to ensure

that the warm air can escape

unhindered.

11210610-01

Installation

*INSTALLATION*

Appliance dimensions

x: Dimensions without wall spacers fitted. Appliance depth is increased by 35mm with the

wall spacers supplied fitted.

11210610-01

Installation

*INSTALLATION*

Changing the door hinging

The appliance is supplied with left-hand

hinging. If right-hand hinging is

required, the hinges must be changed.

Please note that the hinging must not

be changed if this appliance is going to

be installed side by side with another

refrigeration appliance.

Danger of injury and damage

when changing the door hinging!

There is an increased danger of

injury and damage if the refrigeration

appliance is installed by a single

person.

Always change the door hinging with

the help of a second person.

If a door seal is damaged or has

come out of the groove, the door will

not close properly and cooling

performance will be reduced.

Condensate will build up in the

interior and this can cause a build-up

of ice.

Do not damage the door seals and

ensure that they do not come out of

their groove.

Preparing to change the door hinging

To change the door hinging, you will

need the following tools:

Place a suitable cover on the floor in

front of the appliance to protect the

appliance door and your floor from

damage.

Removing the top covers

Close the appliance door.

Remove the cover  by sliding it

forwards from the back and then

lifting it off.

Remove the cover by pulling it

upwards.

Danger of injury when removing

the appliance door!

The appliance door is no longer

secure once the screws in the hinge

plate have been removed.

Hold the appliance door firmly.

11210610-01

Installation

*INSTALLATION*

Removing the door

Loosen the screws in the hinge

plate and pull it upwards and off.

Carefully lift the door up and off and

set it aside.

Changing the door handle over

Take the stoppers out of the

appliance door.

Remove the stopper from the top

of the door and refit it on the opposite

side.

Remove the covers from the

handle, then unscrew the handle

and refit all these parts on the

opposite side of the door.

Take care when refitting the covers 

that they click into position correctly.

Refit the stoppers on the opposite

side.

To change over the spring clamp 

press down on the catch and pull the

spring clamp forwards:

11210610-01

Installation

*INSTALLATION*

Changing over the lower hinge plate

Pull the hinge pin complete with

washer  and adjusting foot 

upwards to remove.

Remove the stopper.

Undo the screws and remove the

hinge plate.

Slightly loosen the screwof the door

closing aid on the hinge plate.

Place the door closing aid  in the

opposite mounting hole in the hinge

plate and then tighten the screw.

Insert the stopper into the other

hole.

Remove the cover.

Remove the screw and screw it

into the outside hole on the opposite

side.

Turn the cover 180° and refit it in

the holes on the opposite side.

Screw the hinge plate  securely into

position on the new hinge side with

the screws.

Reinsert the hinge pin complete

with washer and adjustable

foot. Important: The lug on the

hinge pin must point to the back

again.

Place the door onto the hinge pin

from above.

Close the appliance door.

11210610-01

Installation

*INSTALLATION*

Inserting the upper hinge plate

Fit the hinge plate on the opposite

side and secure it in place with the

screws. If necessary, drill pilot

holes for the screws or use a battery

operated screwdriver.

Replace the covers and on the

opposite side.

Align the door with the appliance

housing using the slots in the lower

hinge plate. Then tighten the screws.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miele Gefrierschrank Handbücher

Miele

Miele F 2462 Vi Bedienungsanleitung

Miele

Miele FNS 28463 E Bedienungsanleitung

Miele

Miele KFN 12943SD edt/cs Bedienungsanleitung

Miele

Miele F 456 i-3 Bedienungsanleitung

Miele

Miele F1411VI Bedienungsanleitung

Miele

Miele F 1411 SF Bedienungsanleitung

Miele

Miele KFN 37682 iD Bedienungsanleitung

Miele

Miele F 1801 Vi Bedienungsanleitung

Miele

Miele KWTN 14826 SDE ed Technisches Datenblatt

Miele

Miele F 12011 S-1 Bedienungsanleitung

Miele

Miele KFN 8701 SE ed-1 Bedienungsanleitung

Miele

Miele F 5122 Ui Bedienungsanleitung

Miele

Miele KFN 37432 iD Bedienungsanleitung

Miele

Miele KWTN 14826 SDE ed/cs-2 Bedienungsanleitung

Miele

Miele F 2671 Vi Bedienungsanleitung

Miele

Miele F 31202 Ui Bedienungsanleitung

Miele

Miele KFN 37692 iDE Bedienungsanleitung

Miele

Miele FN 35402 i Bedienungsanleitung

Miele

Miele FNS 4782 E edt/cs Bedienungsanleitung

Miele

Miele F 1471 Vi Bedienungsanleitung

Miele

Miele KFN 12927 SD edt/cs Montageanleitung

Miele

Miele KFN 29683 D obsw Montageanleitung

Miele

Miele F1413SF Bedienungsanleitung

Miele

Miele KFN 8962 SD ed Bedienungsanleitung

Beliebte Gefrierschrank Handbücher anderer Marken

Siemens

Siemens GU..D SERIES Bedienungsanleitung

Omcan

Omcan FR-CN-0155 Bedienungsanleitung

Beko

Beko FNE290E24W Bedienungsanleitung

Electrolux

Electrolux ARCTIS G 8 60 50-6I Bedienungsanleitung

Electrolux

Electrolux EUF2042AOX Bedienungsanleitung

Dometic

Dometic CoolFreeze CFX95DZ Bedienungsanleitung

Electrolux

Electrolux EUF7000W1 Bedienungsanleitung

Polar Electro

Polar Electro CT330 Bedienungsanleitung

MPM

MPM MPM-145-SK Series Bedienungsanleitung

SAF

SAF PRESTOTIG 200AC/DC Kurzanleitung

Zanussi

Zanussi ZFT11407WA Bedienungsanleitung

AEG

AEG A63190GT Bedienungsanleitung

AEG

AEG A81000TNW0 Bedienungsanleitung

Matsui

Matsui MUC50S15E Bedienungsanleitung

NEFF

NEFF G4344X8 Bedienungsanleitung

Frigidaire

Frigidaire FV 1246 H Bedienungsanleitung

Frigidaire

Frigidaire FFC13K1AW Bedienungsanleitung

Electrolux

Electrolux EU 2400C Bedienungsanleitung