Miele SmartLine CS 7612 FL Bedienungsanleitung
10878121-02
Installation
*INSTALLATION*
Safety instructions for installation
Risk of damage from incorrect installation.
Incorrect installation can cause damage to the SmartLine appliance.
The SmartLine appliance must only be installed by a suitably qualified and
competent person.
Risk of electric shock!
Incorrect connection to the power supply may result in an electric shock.
The SmartLine appliance must be connected to the electrical supply by a
qualified person only.
Damage from falling objects.
Take care not to damage the SmartLine appliance when fitting wall units or a
rangehood above it.
Fit the wall units and the rangehood before the SmartLine appliance.
The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100°C heat-resistant adhesive which will
not dissolve or distort. Any splashbacks must be of heat-resistant
material.
The SmartLine appliance must not be installed over a fridge,
fridge-freezer, freezer, dishwasher, washing machine, washer-dryer
or tumble dryer.
This SmartLine appliance must not be installed above ovens
unless these have a built-in cooling fan.
After installation, the mains connection cable of the SmartLine
appliance must not come into contact with any moving kitchen
component (e.g. a drawer) or be subject to mechanical loads which
could damage it.
Carefully observe the safety clearances listed on the following
pages.
10878121-02
Installation
*INSTALLATION*
Safety distances
Safety distance above the SmartLine
element
The safety distance specified by the
manufacturer of the cooker hood must
be maintained between the SmartLine
element and the cooker hood above it.
If combustible objects are installed
above the SmartLine element (e.g.
cabinets, utensil rail, etc.), a minimum
safety distance of 500mm must be
maintained.
When two or more SmartLine
elements which have different safety
distances are installed together
below a cooker hood, you should
observe the greatest specified safety
distance.
10878121-02
Installation
*INSTALLATION*
Safety distances to the sides and
back of the appliance
The SmartLine appliance should
preferably be installed with plenty of
space on the right and left.
The minimum distance specified
below must be observed between the
rear of the SmartLine element and a tall
unit or room wall.
The minimum distance, specified
below must be adhered to between one
side of the SmartLine element (right or
left) and a tall unit or room wall. A
minimum distance of 300mm must be
observed on the opposite side.
Minimum horizontal distance from the
back edge of the appliance to a
combustible surface:
50mm
Minimum distance on the right side
between the worktop cut-out and the
closest adjacent piece of furniture (e.g.
tall unit) or a room wall:
50mm.
Minimum distance on the left side
between the worktop cut-out and the
closest adjacent piece of furniture (e.g.
tall unit) or a room wall:
50mm.
Minimum safety distance underneath
the SmartLine appliance
To ensure proper ventilation of the
SmartLine appliance, a minimum safety
distance is required between the
SmartLine appliance and an oven,
interim shelf or drawer.
The minimum safety distance from the
lower edge of the SmartLine appliance
to
- the top edge of an oven: 15mm
- the top edge of an interim shelf:
15mm
- the top edge of a drawer: 5mm
- the base of a drawer: 75mm
Interim shelf
It is not necessary to fit an interim shelf
underneath the SmartLine appliance,
but one may be fitted if you wish.
Leave a gap of 10mm at the back of
the shelf to accommodate the mains
connection cable. We recommend a
gap at the front of the SmartLine
appliance of 20mm to ensure good
ventilation.
10878121-02
Installation
*INSTALLATION*
Installation notes –
surface-mounted
Sealing between the SmartLine
appliance and the worktop
The SmartLine appliance and
worktop may be damaged if the
appliance needs to be removed after
it has been sealed with a sealant.
Do not use any sealant between the
SmartLine appliance and the
worktop.
The sealing strip under the edge of
the top part of the appliance
provides a sufficient seal for the
worktop.
Tiled worktop
Grout lines and the hatched area
underneath the SmartLine appliance
frame must be smooth and even. If they
are not, the SmartLine appliance will
not sit flush with the worktop and the
sealing strip underneath the top part of
the appliance will not provide a good
seal between the appliance and the
worktop.
Sealing strip
Dismantling the SmartLine appliance
for service purposes may damage
the sealing strip underneath the edge
of the SmartLine appliance.
Always replace the sealing strip
before reinstalling the cooktop.
10878121-02
Installation
*INSTALLATION*
Installing several
SmartLine appliances
The gaps between the individual
SmartLine appliances must be sealed
with a silicone sealant that is heat-
resistant to at least 160°C. With flush-
fit installation, the gap between the
SmartLine appliance(s) and the worktop
must also be sealed with a silicone
sealant that is heat-resistant to at least
160°C.
After installation, the SmartLine
appliances must be easily accessible
from below, so that the bottom half of
the casing can be removed for
maintenance. If the SmartLine
appliances are not accessible from
below, the sealant must be removed so
that they can be removed.
Combination with a downdraft
extractor
If the SmartLine appliance is installed in
combination with a downdraft extractor,
the latter must be installed first.
10878121-02
Installation
*INSTALLATION*
Worktop cut-out – surface-mounted
B
500 + 1
ß
R 4
B
10
0
10
+ 1
+ 1
10878121-02
Installation
*INSTALLATION*
Installation with a downdraft extractor
Sample combinations Numberxwidth [mm] Dimension
B
[mm]
Cooking
appliances
Downdraft
extractor
1x378 1x120 481
2x378 1x120 862
1x378
1x620
2x120 1226
3x378 2x120 1365
2x378
1x620
2x120 1607
4x378 2x120 1746
1x620 2x120 845
10878121-02
Installation
*INSTALLATION*
Installation without a downdraft extractor
Sample combinations Numberxwidth [mm] DimensionB
[mm]
Cooking appliances
1x378 359
2x378 740
1x378
1x620
982
3x378 1121
2x378
1x620
1363
4x378 1502
2x378
1x800
1554
2x378
1x936
1680
10878121-02
Installation
*INSTALLATION*
Spacer bars – surface-mounted
If you are installing several appliances, you must fit spacer bars between them.
The clips supplied with the spacer bars are only required for installing a
CSDA700xFL.
Installing 3 appliances and 2 spacer bars
10878121-02
Installation
*INSTALLATION*
Installation dimensions – Surface-mounted
All dimensions in this instruction booklet are given in mm.
aFront
bMains connection cable, L=2,000mm
Andere Handbücher für SmartLine CS 7612 FL
1
Inhaltsverzeichnis
Andere Miele Küchengerät Handbücher
Miele
Miele APFD 201 Bedienungsanleitung
Miele
Miele MLT4600 Gebrauchsanweisung
Miele
Miele EVS 6214 Bedienungsanleitung
Miele
Miele KWT 6722 iS Bedienungsanleitung
Miele
Miele TepanYaki CS 1327 Technisches Datenblatt
Miele
Miele EVS 6114 Bedienungsanleitung
Miele
Miele HUB 5000-XL Bedienungsanleitung
Miele
Miele HUB 5000-XL Bedienungsanleitung
Miele
Miele KWT 6322 UG Bedienungsanleitung
Miele
Miele KWT 2601 SF Bedienungsanleitung
Miele
Miele PRI 210 Bedienungsanleitung
Miele
Miele KWT 6322 UG Bedienungsanleitung
Miele
Miele HGE 70 Bedienungsanleitung
Miele
Miele TepanYaki CS 1327 Bedienungsanleitung
Miele
Miele MLT4700 Gebrauchsanweisung
Miele
Miele APWD 325 Bedienungsanleitung
Miele
Miele KM 403 Bedienungsanleitung
Miele
Miele CT 400 P Bedienungsanleitung
Miele
Miele KWT 6833 SG Bedienungsanleitung
Miele
Miele H 2265-1 B Bedienungsanleitung
