Miele K 26 1 Vi Series Bedienungsanleitung
Side-by-side Kit KSK 2002
en Side-by-side combination Vi models
Installation instructions
fr Trousse de juxtaposition côte à côte pour les
modèles Vi
Instructions d'installation
M.-Nr. 11093710
en - Securing a side-by-side combination
3
Side-by-side installation
These side-by-side merging kit installa-
tion instructions apply to the following
models:
– K26x1Vi,K28x1Vi,K29x1Vi
– F2411Vi,F28x1Vi,F29x1Vi
– F24x1Vi,F26x1Vi
– KF28x1Vi,KF29x1Vi
– KWT26x1Vi,KWT26x1ViS
It is essential to read these Installa-
tion Instructions as well as the Oper-
ating and Installation Instructions for
your refrigeration appliances before
setup, installation, and use.
Risk of injury due to electric
shock.
The supply voltage is applied to the
appliance even if it is switched off.
Unplug the power cords for both re-
frigeration appliances prior to com-
mencing side-by-side installation.
The refrigeration appliances must be
installed side by side before in-
stalling them in the niche.
Risk of damage and injury due to
appliances tipping over.
The refrigeration appliances are very
heavy and can tip forwards when the
doors are open.
Keep the doors shut until the appli-
ances have been built in and secured
in their housings in accordance with
the Operating and Installation In-
structions.
Due to their weight and size, the re-
frigeration appliances must be in-
stalled by two people.
The following tools are required for
side-by-side installation:
– Torx T20 screwdriver
– Cordless screwdriver
– Hammer
– Pipe wrench
In addition:
– Material to place under the appli-
ances to protect the floor
– Adhesive tape
en - Securing a side-by-side combination
4
. . . with partition wall
The wall a between the side-by-side
appliances must be at least
5/8" (16mm) thick.
If the door hinges of the refigeration
appliances are next to each other,
you must take into account the thick-
ness of the cabinet fronts and door
handles so that the appliance doors
do not collide and become damaged
if they are opened at the same time.
a
If the partition wall a is narrower than
6 5/16" (160mm), you will need the
side panel heater from the side-by-
side merging kit to prevent condensa-
tion from forming and any resulting
damage (see section “Installing the side
panel heater”).
The side panel heater is attached to
the right side of the appliance that is on
the left (when seen from the front).
When planning niches, please note
that the niche into which the appli-
ance with the side panel heater is
installed must be
1/8"-1/4"(3–5mm) wider.
Connecting the side panel heater
leads to higher energy consumption.
en - Securing a side-by-side combination
5
The appliances are then secured indi-
vidually in their niche using the supplied
installation material (follow the instruc-
tions in the enclosed Operating and In-
stallation Instructions).
. . . without partition wall
If the appliances are to be installed next
to each other without a partition wall
between them, they will need to be
joined together with the side-by-side
merging kit. In addition, you must install
the side panel heater to prevent con-
densation from forming and any result-
ing damage (see from section “Prepar-
ing the refrigeration appliances”).
The door hinges of the appliances
must not be located next to each
other, otherwise the appliance doors
will collide and become damaged if
they are opened at the same time.
Connecting the side panel heater
leads to higher energy consumption.
en - Securing a side-by-side combination
6
Preparing the refrigeration ap-
pliances
Place both refrigeration appliances
side by side in the required positions,
leaving a small gap between them.
Do not remove the spacers from the
insides of the appliances.
Remove the bracket plates from the
handle sides on both appliances.
Secure the supplied hinge halves
onto both appliances.
Secure the fixing lugs onto both ap-
pliances. Check the position of both
appliances again.
en - Securing a side-by-side combination
7
Installing the heating mat
The heating mat must be attached to
the right side of the appliance that is on
the left (when seen from the front).
Insert the pins into their respective
holes in the heating mat 1.).
Remove the protective strip from the
adhesive tape 2.).
Maintain a gap between the bottom
of the heating mat and the bottom of
the appliance, and insert the pins into
the holes at the top 3.).
Push the heating mat onto the appli-
ance from top to bottom and insert
the pins into the bottom holes 4.).
Loosen the screw on the plug cover
5.).
Remove the plug cover 6.).
Connect the power cord 7.).
Reinstall the plug cover 8.).
Tighten the screw on the plug cover
9.).
11.
Slightly loosen the screws on the
back of the appliance 10.).
Push the supplied cord cover into the
slots of the side panel heater.
Hook the cord cover onto the screws
on the back of the appliance 11.).
Now tighten the screws 12.).
en - Securing a side-by-side combination
8
Connecting the refrigeration
appliances
Push the appliances together at the
back until the hinge halves engage.
Insert the pins into the hinge halves
from the top.
Push the appliances as close to-
gether as possible at the front.
In addition, pull both appliances to-
gether at the front with a pipe
wrench.
From the front, push the longer metal
clip of the two supplied into the bot-
tom fixing lug. If required, use a ham-
mer.
en - Securing a side-by-side combination
9
Remove the two screws from the
tops of the appliances.
Use these screws to secure the sup-
plied anti-tip brackets.
Both anti-tip brackets can be found in
the refrigeration appliance installation
kit.
In addition, press both anti-tip brack-
ets together with a pipe wrench.
From the top, insert the shorter of the
supplied metal clips into the fixing
lugs. If required, use a hammer.
Now loosen the screws on the tops of
the appliances again and remove
both anti-tip brackets.
You will need the anti-tip brackets to
secure the niche.
en - Securing a side-by-side combination
10
Then reinstall the screws on the tops
of the appliances.
Tip: Now you can continue installing
the appliances. For this purpose, ob-
serve the enclosed operating and instal-
lation instructions for each of the appli-
ances.
Insert the cover strip into the gap be-
tween the refrigeration appliances.
You have now finished installing the
side-by-side combination.
Dieses Handbuch passt für folgende Modelle
12
Inhaltsverzeichnis
Sprachen:
Andere Miele Kühlschrank Handbücher
Miele
Miele K 32222 i Bedienungsanleitung
Miele
Miele KF 7564 S ed-3 Technisches Datenblatt
Miele
Miele KF 7642 SN Technisches Datenblatt
Miele
Miele KD 3528 Sed Technisches Datenblatt
Miele
Miele KT 3538 Sed Technisches Datenblatt
Miele
Miele K 14827 SD Bedienungsanleitung
Miele
Miele KS3x422iD Bedienungsanleitung
Miele
Miele K 851 iD Technisches Datenblatt
Miele
Miele K 9454 iF Technisches Datenblatt
Miele
Miele K 2601 Vi Bedienungsanleitung
Miele
Miele K 1911 SF Benutzerhandbuch
Miele
Miele KD 673 i Technisches Datenblatt
Miele
Miele K 35222 iD Bedienungsanleitung
Miele
Miele K 852i Technisches Datenblatt
Miele
Miele K 12820 SD ed Technisches Datenblatt
Miele
Miele KF1913 Vi Gebrauchsanweisung
Miele
Miele KF 882 iD-1 Technisches Datenblatt
Miele
Miele KT 12510 S Technisches Datenblatt
Miele
Miele KFN 15842 D ed/cs Bedienungsanleitung
Miele
Miele K 854 i-1 Bedienungsanleitung
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
NEFF
NEFF KI181 Series Bedienungsanleitung
