Miele KFN 14943 SD ed Bedienungsanleitung

Installation Instructions

KFN 14943 SD en - CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

,Avoid the risk of electrical shock

- Plug into a grounded 3-prong

outlet.

- Do not move the ground plug.

- Do not use an adapter.

- Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or electrical

shock.

Improper connection of the

equipment grounding conductor

may result in electric shock.

If you are in any doubt as to whether

the appliance has been properly

grounded, have the appliance

checked by a qualified electrician or

service technician.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer will

not be held responsible for damage

or injury arising from unauthorized

work.

Before installing the appliance,

verify that the voltage, load and

circuit rating information found on

the data plate match the household

electrical supply.

If there are any questions regarding the

electrical connection of this appliance

to the power supply, please consult a

licensed electrician or call the Miele

Technical Service.

V1-800-565-6435

The appliance is supplied with a

UL-listed, 3-wire power cord and

NEMA 5-15 P plug ready for connection

to a 120 V, 60 Hz supply.

The fuse rating is 15 amps.

The appliance requires a 3-wire

receptacle.

The receptacle must be installed by a

licensed electrician only.

In the case of side-by-side installations,

a separate outlet must be used for each

appliance.

Ideally, the power outlet should be next

to the appliance and easily accessible.

Do not connect the appliance to the

power supply by an extension cord.

Extension cords do not guarantee the

required safety of the appliance

(danger of overheating).

This appliance must not be connected

to the inverter of an autonomous power

supply, e.g. a solar power system.

When switching the appliance on, a

surge in power could trigger the safety

cut-out mechanism. This could damage

the electronic unit.

The appliance must not be used with

so-called energy saving devices. These

reduce the energy supply to the

appliance which could then become

too warm. Using such devices could

alter the specification of the product.

If any changes are needed to the

household wiring or power supply, this

work must be performed by a qualified

electrician.

Electrical information

Do not place any devices that

produce heat (such as a toaster or

microwave) on top of the appliance.

This would increase the energy

consumption of the appliance.

This fridge/freezer should not be

placed side-by-side with another

one.

Because the appliance does not

have heated side walls, a

side-by-side arrangement can lead

to a build-up of condensation water.

Contact your dealer for advice.

Location

The appliance should not be installed

directly next to a heat source (such as

a kitchen range or a heater) or under a

window in direct sunlight. The higher

the ambient temperature, the longer the

appliance?will run and the higher the

energy consumption.

Choose a dry, well-ventilated room for

installation.

Climate class

The appliance is designed for use

within a certain climate range (room

temperature range) and should not be

used outside this range. The climate

range is stated on the data plate inside

the appliance.

Climate class Room temperature

+10 °C to +32 °C

+16 °C to +32 °C

+16 °C to +38 °C

+16 °C to +43 °C

If the room is too cold, it will cause the

cooling system in the appliance to

remain off for too long. This may lead to

higher temperatures in the appliance

and the frozen food may even start

thawing.

Proper ventilation

The air behind the appliance gets

warm. In order to ensure adequate

ventilation, you must make sure that the

ventilation slits are not covered or

blocked in any way.

Also, the ventilation slits must be

dusted or cleaned on a regular basis.

Installation

^First remove any cable clips from the

rear of the appliance.

^Check that all the parts on the rear of

the appliance are free to move.

Carefully bend any attached

components out of the way.

^Gently slide the appliance into the

desired location.

^The rear of the appliance can be

directly against the wall.

Installation information

Adjustments

^Use the wrench provided to adjust

the front feet as needed, so that the

appliance is levelled.

Supporting the appliance door

^In any case unscrew foot auntil it is

on the ground. Then unscrew the foot

another 90°.

Installation information

Appliance dimensions

ABC DE

KFN 14943 SD ed/cs 2020 mm

(79 17/32")

747 mm

(29 3/8")

630 mm

(24 13/16")

1330 mm

(52 3/8")

790 mm

(31 3/32")

If the gap between the rear of the appliance and the wall is less than 2 inch

(51 mm), the power consumption level may increase.

Installation information

The appliance comes with right-hand

hinging. If left-hand door hinging is

required, the door hinge must be

changed:

You will need the following tools to

change the door hinging:

– a Phillips screwdriver,

– a flathead screwdriver,

– various sizes of Torx screwdrivers,

– an open-end wrench.

Always change the door hinging

with the assistance of another

person.

Removing the door handles:

^When you pull on the door handle a,

the sidebar bmoves backwards.

^Pull the sidebar bforcefully

backwards out of the track.

^Now loosen the 4 screws (Torx 15) in

the mounting plate and remove the

handle.

^Remove the covers from the opposite

side and place them on the holes that

are now empty.

Changing the door hinging

Before changing the hinging,

remove any items of food from the

shelves in the appliance door.

Removing the top soft-close

mechanism:

^Open the top door of the appliance.

^Loosen panel afrom the soft-close

mechanism: From below, slide a

flathead screwdriver into the

recesses, then slowly and carefully

lift off the panel.

Be careful not to damage the door

seal.

If the door seal is damaged, the

appliance door may not close

properly and there will not be

enough refrigeration!

^Slide panel ain the direction of the

appliance and leave it hanging

between the door and the appliance.

^Place the securing device b

(supplied with the appliance) on the

soft-close mechanism cso that it

engages.

With the securing device in place, the

joint cannot snap shut. Do not remove

the securing device until instructed to!

^Using a flathead screwdriver,

carefully lift the top and the bottom of

the cover dfrom the retainer.

^Push pin eup and out using a

flathead screwdriver.

Changing the door hinging

^Remove cover d.

Now the soft-close mechanism and the

appliance are no longer connected.

^Remove panel a.

^Push the shock absorber arm fas

far as possible towards the handle

side.

^Loosen the screws gon the

soft-close mechanism and the

spacer.

^In the middle, pry out the housing

with the soft-close mechanism using

a flathead screwdriver.

^Then, pry the housing with the

soft-close mechanism out of the

retainer from the appliance side.

^Put the soft-close mechanism aside.

^Push the spacer out towards the

hinge side.

^Put the spacer aside.

Removing the top door of the

appliance:

^Loosen the cover hby carefully

sliding a flathead screwdriver from

below into the recess.

^Remove the cover htogether

with?the mounting bracket i.

^Loosen the mounting bracket ifrom

the cover hby pushing it slightly to

the left and then removing the cover

plate towards the front.

^Turn the mounting bracket i180°.

^Place the cover hon the front of the

mounting bracket iand push it to

the right. The writing must be visible.

^Unscrew the bearing jmechanism,

turn it 180° and replace it on the

opposite side. If necessary,

pre-punch the screw holes.

^Remove the top cover kby pushing

it from back to front and lifting it up.

^Remove cover lupwards.

Changing the door hinging

Caution! The top door of the

appliance is no longer secured as

soon as the hinge bracket is

removed!

^Close the top door of the appliance.

^Loosen the screws mon the top

hinge bracket nand remove the

hinge bracket by pulling up.

^Carefully lift and remove the top door

of the appliance and set aside.

^Make sure that the bearing pin in the

middle of the appliance stays in

place, otherwise nothing is holding

the bottom door of the appliance!

^Engage the cover htogether with

the mounting bracket ion the

opposite side.

^Now place the cover don the

opposite side.

Removing the bottom soft-close

mechanism:

^Open the bottom door of the

appliance.

^Loosen panel afrom the soft-close

mechanism: Slowly pry the panel off

from the top.

Be careful not to damage the door

seal.

If the door seal is damaged, the

appliance door may not close

properly and there will not be

enough refrigeration!

^Slide panel ain the direction of the

appliance and leave it hanging

between the door and the appliance.

^Place the securing device b

(supplied with the appliance) on the

soft-close mechanism c.

With the securing device in place, the

joint cannot snap shut. Do not remove

the securing device until instructed to!

^From the side, carefully lift off the

cover dusing a flathead

screwdriver.

^If necessary, tilt the appliance

backwards slightly with the

assistance of another person.

Changing the door hinging

^Push pin eup and out.

Now the soft-close mechanism and the

appliance are no longer connected.

^Remove panel a.

^Push the shock absorber arm fas

far as possible towards the handle

side.

^Loosen the screws gon the

soft-close mechanism and the

spacer.

^In the middle, pry out the housing

with the soft-close mechanism using

a flathead screwdriver.

^Then, pry the housing with the

soft-close mechanism out of the

retainer from the appliance side.

^Put the soft-close mechanism aside.

^Push the spacer out towards the

hinge side.

^Put the spacer aside.

Removing the bottom door of the

appliance:

^Close the bottom door of the

appliance.

^Pull the bearing pin iin the middle

of the appliance up and out.

^Carefully lift and remove the bottom

door of the appliance and set aside.

^Pull cover joff.

^Unscrew the hinge bracket k, rotate

it 180°, then screw it onto the

opposite side.

^Turn the plastic cap h180° and

replace it on the hinge bracket kin

the middle.

^Now place the cover jon the other

side.

Changing the door hinging

Andere Handbücher für KFN 14943 SD ed

Inhaltsverzeichnis

Andere Miele Kühlschrank Handbücher

Miele

Miele KFN 28132 D ws Bedienungsanleitung

Miele

Miele KFN 7795 D Bedienungsanleitung

Miele

Miele KFN 14943 SD ed Bedienungsanleitung

Miele

Miele KFN 9758 iD Bedienungsanleitung

Miele

Miele K 622 Ui-1 Bedienungsanleitung

Miele

Miele TX3587 Bedienungsanleitung

Miele

Miele KFN 28132 D ws Bedienungsanleitung

Miele

Miele KF 2801 SF Bedienungsanleitung

Miele

Miele KF 2981 Vi Bedienungsanleitung

Miele

Miele KS 7793 D Bedienungsanleitung

Miele

Miele Independence KF1811Vi Gebrauchsanweisung

Miele

Miele KFN 29243 D ed/cs Bedienungsanleitung

Miele

Miele K 32222 i Bedienungsanleitung

Miele

Miele K 2319 S Bedienungsanleitung

Miele

Miele K 14820 SD ed Montageanleitung

Miele

Miele K 31222 Ui Bedienungsanleitung

Miele

Miele K 854 i-1 Bedienungsanleitung

Miele

Miele KD 1450 SD Technisches Datenblatt

Miele

Miele KT 12510 S-1 Technisches Datenblatt

Miele

Miele K 14820 SD ed Technisches Datenblatt

Miele

Miele KFN 8997 SE ed Technisches Datenblatt

Miele

Miele KFN 14923 SDE ed Technisches Datenblatt

Miele

Miele KFN 4374 ED ws Bedienungsanleitung

Miele

Miele KFN 15943 DE edt/cs Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung