Miele KFN 14943 SDE ED Bedienungsanleitung
Operating and Installation
Instructions
Fridge/freezer combination
with ice cube maker
NoFrost system
and DynaCool
KFN 14943 SDE ed
To prevent accidents
and machine damage
read these instructions
before
installation or use. M.-Nr. 07 792 920
en-CA
Notes on connecting to the
water supply
The appliance must be connected to
the water supply by a qualified
professional.
The water being used should meet
the drinking water standards of the
country where the machine is used.
–The appliance is in compliance with
the requirements of IEC 61770 and
EN 61770.
– All units and systems used to deliver
the water to the appliance must
conform with the regulations of the
respective country.
– The appliance must be connected to
a cold water supply only.
– The water pressure must be between
1.5 and 6 bar.
–The stainless steel hose is 1.5 m
long.
The stainless steel hose can be
lengthened with an extension hose. It
must be fitted by a qualified
technician.
The extension hose is available from
Miele Customer Service.
–A water shut-off valve must be
provided between the stainless steel
hose and the household water
supply to ensure that the water
supply can be cut off if necessary.
The water shut-off valve must be
accessible after installation.
Connecting to the water
supply
Disconnect the refrigerator/freezer
from the electric power supply prior
to connecting to the water supply.
A water shut-off valve with 3/4" thread is
required for connection to the water
supply.
^Connect the straight end of the
stainless steel hose to the water
shut-off valve.
^Ensure that it is properly screwed into
position.
Before using the appliance for the first
time, the water supply line needs to be
purged of air by a qualified technician:
–The stainless steel hose should be
filled with as much water as possible
immediately before connecting to the
solenoid valve.
–Mop up any spillage with a cloth.
Water supply
50
^Attach the stainless steel hose to the
solenoid valve at the bottom rear side
of the appliance.
^Ensure that the hose is correctly fitted
and that it is water-tight.
^Slowly open the water shut-off valve
and check the whole water system
for leaks.
^The appliance can now be
connected to the power supply (see
"Electrical connection").
^Slide the appliance into the desired
position.
When doing so, make sure that the
stainless steel hose does not get kinked
or damaged.
After a maximum of 24 hours, the
first ice cubes will drop out of the ice
cube maker and collect in the
drawer.
Water supply
51
,Avoid the risk of electrical shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock.
If you are in any doubt as to whether
the appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer will
not be held responsible for damage
or injury arising from unauthorized
work.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
V1-800-565-6435
The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection
to a 120 V, 60 Hz supply.
The fuse rating is 15 amps.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licened electrician only.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance.
Ideally, the power outlet should be next
to the appliance and easily accessible.
Do not connect the appliance to the
power supply by an extension cord.
Extension cords do not guarantee the
required safety of the appliance
(danger of overheating).
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
Electrical information
52
Do not place any devices that
produce heat (such as a toaster or
microwave) on top of the appliance.
This would increase the energy
consumption of the appliance!
This fridge/freezer should not be
placed side-by-side with a second
model.
Because the appliance does not
have heated side walls, a
side-by-side arrangement can lead
to the build-up of condensation
water.
Contact your dealer for advice.
Location
The appliance should not be installed
directly next to a heat source (such as
a kitchen range or a heater) or in direct
sunlight. The higher the ambient
temperature, the longer the appliance
will run and the higher the energy
consumption.
Choose a dry, well-ventilated room for
installation.
Climate range
The appliance is designed for use
within a certain climate range (room
temperature range) and should not be
used outside this range. The climate
range is stated on the data plate inside
the appliance.
Climate range Room temperature
SN
N
ST
T
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
If the room is too cold, it will cause the
cooling system in the appliance to
switch off for too long. This may lead to
higher temperatures in the appliance
and the frozen food may even start
thawing!
Proper ventilation
The air behind the appliance gets
warm. In order to ensure adequate
ventilation, you must make sure that the
ventilation slits are not covered or
blocked in any way.
Also, the ventilation slits must be
dusted/cleaned on a regular basis.
Installation
^First remove any cable clips from the
rear of the appliance.
^Check that all the parts on the rear of
the appliance are free to move.
Remove any obstructions.
^Gently slide the appliance into the
desired location.
^The rear of the appliance can be
directly against the wall.
Installation information
53
Adjustments
^Use the wrench provided to adjust
the feet as needed, so that the
appliance is level.
^If necessary, unscrew the foot a
from the hinge bracket in order to
support the appliance door.
Installation information
54
Appliance dimensions
ABC
KFN 14943 SDE ed 2020 750 630
Installation information
55
The appliance comes with right-hand
hinging. If left-hand door hinging is
preferred, then follow these instructions
to change the door hinge:
You will need the following tools:
–a crosstip screwdriver,
–a flathead screwdriver,
–various sizes of Torx screwdrivers,
–a fork wrench.
Always change the door hinging
with the assistance of another
person.
Removing the door handles:
^When you pull on the door handle a,
the sidebar bmoves backwards.
^Pull the sidebar bbackwards out of
the track.
^Now loosen the 4 screws (Torx 15) in
the mounting plate and remove the
handle.
^Remove the covers from the opposite
side and place them on the holes that
are now vacant.
Changing the door hinging
56
Before changing the hinging,
remove any items of food from the
shelves in the appliance door.
Removing the top soft-close
mechanism:
^Open the top door of the appliance.
^Loosen the panel afrom the
soft-close mechanism: From below,
slide a flathead screwdriver into the
recesses, then slowly and carefully
lift off the panel.
Be careful not to damage the door
seal.
If the door seal is damaged, the
appliance door may not close
properly and there will not be
enough refrigeration!
^Slide the panel ain the direction of
the appliance and leave it hanging
between the door and the appliance.
^Place the securing device b
(supplied with the appliance) on the
soft-close mechanism cso that it
engages.
With the securing device in place, the
joint cannot snap shut. Do not remove
the securing device until instructed to!
^Using a flathead screwdriver,
carefully lift the top and the bottom of
the cover dfrom the retainer.
^Push the pin eup and out using a
flathead screwdriver.
Changing the door hinging
57
^Remove the cover d.
Now the soft-close mechanism and the
appliance are no longer connected.
^Remove the panel a.
^Push the shock absorber arm fas
far as possible towards the handle
side.
^Loosen the three screws gon the
soft-close mechanism and the
spacer.
^In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^Lay the soft-close mechanism aside.
^Push out the spacer towards the
hinge side.
^Lay the spacer aside.
Removing the top door of the
appliance:
^Loosen the cover hby carefully
sliding a flathead screwdriver from
below into the recess.
^Remove the cover htogether with
the mounting bracket i.
^Loosen the mounting bracket ifrom
the cover hby pushing it slightly to
the left and then removing the cover
plate towards the front.
^Turn the mounting bracket i180°.
^Place the cover honto the front of
the mounting bracket iand push it
to the right. The writing must be
visible.
^Unscrew the bearing jmechanism,
turn it 180° and replace it on the
opposite side. If necessary,
pre-punch the screw holes.
^Remove the top cover kby pushing
it from back to front and lifting it up.
^Remove the cover lupwards.
Changing the door hinging
58
Andere Handbücher für KFN 14943 SDE ED
2
Inhaltsverzeichnis
Andere Miele Kühlschrank Handbücher
Miele
Miele KF 2981 Vi Bedienungsanleitung
Miele
Miele KFNS 37692 iDE-1 Bedienungsanleitung
Miele
Miele KFN 9855 iDE Bedienungsanleitung
Miele
Miele KF 1801 Vi Bedienungsanleitung
Miele
Miele K 2316 S Technisches Datenblatt
Miele
Miele K 2601 Vi Bedienungsanleitung
Miele
Miele KF 2801 Vi Bedienungsanleitung
Miele
Miele Independence KF1811Vi Gebrauchsanweisung
Miele
Miele KF 1911 Vi Technisches Datenblatt
Miele
Miele KFN 4795 DD Bedienungsanleitung
Miele
Miele KT 12510 S-1 Technisches Datenblatt
Miele
Miele KT 12510 S Technisches Datenblatt
Miele
Miele KF 2811 SF Bedienungsanleitung
Miele
Miele K 9554 iDF Montageanleitung
Miele
Miele KF 2981 Vi Bedienungsanleitung
Miele
Miele K 854 i-1 Technisches Datenblatt
Miele
Miele K 11820 SD Bedienungsanleitung
Miele
Miele K 28202 D w Bedienungsanleitung
Miele
Miele K 12020 S Bedienungsanleitung
Miele
Miele KFNS 37692 iDE Bedienungsanleitung
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
Stengel
Stengel KU 1101 A++ Bedienungsanleitung
