Miele DA 6690 D Bedienungsanleitung

Installation Instructions

DA6690 D en - CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

Installation

Before installation

Before installing the appliance,

read all of the information contained

in this chapter and also in the "IM‐

PORTANT SAFETY INSTRUCTIONS"

section.

Installation parts

4 screws, ¹/₄" x 4 ⁵/₁₆"

(7 x 110 mm) and

4 plugs, ³/₈" x 3 ¹/₈" (10 x 80 mm)

for securing the ventilation hood to the

ceiling (not for use in USA / CDN).

The screws and plugs are designed

for use in solid ceilings only.

Use different fasteners for other ceil‐

ing construction types. Make sure

that the ceiling can support the load.

4 extension piece holders

for aligning and securing the telescopic

chimney

4 screws M³/₁₆" x ⁵/₁₆"

(M4 x 8.5 mm)

for securing the extension piece hold‐

ers.

14 screws M³/₁₆" x ⁵/₁₆"

(M4 x 8 mm)

for securing the spacer frame and se‐

curing the hood to the installation

frame.

1 screw M³/₁₆" x ⁵/₈" (M4 x 16 mm)

for securing the chimney.

DUI 32 recirculation kit for recircula‐

tion mode

(not supplied, available as an optional

accessory). The kit includes a direc‐

tional unit, aluminum hose, and hose

clips.

Installation

Appliance dimensions

aMounting area for the exhaust ducting and power cable. In recirculation mode,

only the power cord is required.

bPossible height range for appliance in vented mode

cPossible height range for appliance in recirculation mode

dAlternative installation with spacer frame

eAir vent positioned at the top for recirculation

Installation

fA power cord is required to connect the hood to the socket in the ceiling. With

extraction mode flexible ducting is also required.

Exhaust connection 6" (150 mm)

Distance between cooktop and ventilation hood (S)

Provided a larger distance is not given by the manufacturer of the cooktop, fol‐

low the minimum safety distances between a cooktop and the bottom of the

hood.

Please also observe the information contained in the "IMPORTANT SAFETY IN‐

STRUCTIONS" section.

Minimum distance S

Cooking appliance Miele

appliance Non-Miele

appliance

Electric/Induction cooktop 24" (610 mm)

Electric grill, deep fat fryer (electric) 26" (660 mm)

Multi-burner gas cooktop

≤43,000 BTU/hr (12.6 W),

no burner >15,000 BTU/hr (4.5 kW).

26" (660 mm) 30" (760 mm)

Multi-burner gas cooktop

≤73,800 BTU/hr (21.6 W),

no burner >16,500 BTU/hr (4.8 kW)

30" (760 mm)

Multi-burner gas cooktop

>73,800 BTU/hr (21.6 W),

or one of the burners >16,500 BTU/hr (4.8 kW)

Not possible

Single-burner gas cooktop

≤20,500 BTU/hr (6 kW) 26" (660 mm) 30" (760 mm)

Single-burner gas cooktop

>20,500 BTU/hr (6 kW)

≤27,600 BTU/hr (8.1 kW)

30" (760 mm)

Single-burner gas cooktop

>27,600 BTU/hr (8.1 kW) Not possible

Installation

Installation recommendations

– We also recommend a distance of at

least 25 ¹/₂" (650 mm) above electric

cooktops to provide more workspace

and easier cooking under the hood.

– When selecting an installation height,

always take the user height into con‐

sideration. Users should have ample

space to work comfortably on the

cooktop and reach the ventilation

hood controls with ease.

– Please note that the greater the dis‐

tance from the cooktop, the less ef‐

fective the hood is at drawing in the

cooking vapors.

– To achieve optimal vapor extraction,

make sure that the hood covers the

cooktop. The hood should be posi‐

tioned centrally over the cooktop, not

to the side or rear.

– The cooktop should be no wider than

the hood. Preferably, it should be

narrower.

– The mounting area must be easily

accessible. The ventilation hood

should be easy to reach and disas‐

semble in case a service call is nec‐

essary. This should be taken into

consideration when planning the po‐

sition of cupboards, shelves, ceilings

or decorative elements in the vicinity

of the ventilation hood.

Structural support

The hood must be attached to rigid

structural framing that is supported

in its entirety by the ceiling joists, or

to the ceiling joists directly. Do not

attach the plate directly to the ceiling

with anchors, toggle bolts, etc.

Removing the protective film

The housing components are covered

by a protective film to prevent them

from becoming damaged during trans‐

port.

Please remove this film before instal‐

ling the housing components. It can

be peeled off easily without any addi‐

tional tools.

Installation

8 5/8"

220 mm

8 5/8"

220 mm

dai3435aus

Draw two intersecting lines on the

ceiling.

For vented mode:

– Place a section of the exhaust duct‐

ing in the ceiling and feed it down

through the cross-sectional area as

illustrated. Exhaust ducting of ap‐

prox. 27 ⁹/₁₆" (700 mm) length is re‐

quired between the ceiling and the

hood exhaust socket.

– Secure the exhaust ducting to the ex‐

haust socket, e.g. with a hose clip

(available as an optional accessory)

on flexible ducting.

Place the power cord and guide it

through the ceiling in the area shown.

A power cord approx. 27 ⁹/₁₆"

(700 mm) in length is required be‐

tween the ceiling and the hood con‐

nectors.

Installation

Use a knife to release the four

spacers and the two covers from the

spacer frame supplied.

Use the spacer frame as a drilling

template. Place it on the ceiling with

the arrows pointing forwards. Using

the notches, align the spacer frame

on the intersecting lines and make

pencil marks for the drill holes.

Drill four holes ³/₈" (10 mm), ap‐

prox. 4 ¹/₂" (115 mm) deep for the

plugs supplied.

Place the four plugs in the holes and

screw in the four screws so that they

protrude by approx. 1 ³/₁₆" (30 mm).

Installation

The spacer frame can be installed be‐

tween the chimney and the ceiling. This

creates a shadow which gives the illu‐

sion of a gap between the ceiling and

the chimney. This is useful if the ceiling

is not level or is uneven. The hood is

aligned vertically with the spacers sup‐

plied. Visual irregularities between the

chimney and the ceiling are then con‐

cealed by the shadow.

If you wish to install the hood with the

spacer frame, remove the four inserts

from the fixing holes.

Mount the spacer frame onto the in‐

stallation frame.

Installation

Hang the installation frame on the

four screws. The front of the frame is

marked with a "V".

If using the spacer frame, place the

two covers into the fixing holes.

Align the installation frame and se‐

cure it with the screws.

The spacers, which were removed

from the spacer frame at the start,

can be used to align the hood verti‐

cally.

Installation

Holding the installation frame secure‐

ly, remove the two fixing screws and

extend the installation frame to its

maximum length.

Replace the screws.

The directional unit from recirculation

kit DUI 32 (optional accessory) is instal‐

led for recirculation mode (RM):

Bend the four retaining tabs on the

installation frame outwards.

Place the power cord inside the in‐

stallation frame.

Fit the directional unit as shown, not‐

ing the marking on the front.

Bend the retaining tabs back and ap‐

prox. 45° inwards to hold the direc‐

tional unit in place.

Andere Handbücher für DA 6690 D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miele Dunstabzugshaube Handbücher

Miele

Miele DA 186 Bedienungsanleitung

Miele

Miele PUR 68 W Bedienungsanleitung

Miele

Miele DA 6698 D Bedienungsanleitung

Miele

Miele DA 429-4 Technisches Datenblatt

Miele

Miele DA 1260 Bedienungsanleitung

Miele

Miele DA 2808 Bedienungsanleitung

Miele

Miele DA 403 Bedienungsanleitung

Miele

Miele DA 289-3 Stücklistenhandbuch

Miele

Miele DA 6690 D EXT Bedienungsanleitung

Miele

Miele DA 403 Bedienungsanleitung

Miele

Miele DFB 55 Bedienungsanleitung

Miele

Miele DA 6590 D Bedienungsanleitung

Miele

Miele DA 6798 W Bedienungsanleitung

Miele

Miele DA 239-3 Bedienungsanleitung

Miele

Miele DA 3160 Bedienungsanleitung

Miele

Miele DA 249-4 Bedienungsanleitung

Miele

Miele DA 3466 Bedienungsanleitung

Miele

Miele DAS 4940 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Miele

Miele DA 249-3 Bedienungsanleitung

Miele

Miele DA 289 Stücklistenhandbuch

Miele

Miele DA 2906 EXT Bedienungsanleitung

Miele

Miele DA 327 i Technisches Datenblatt

Miele

Miele DA 7000 D Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch

Caple

Caple CCH100 Handbuch