MikroElektronika DsPICPRO Bedienungsanleitung

SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD

MikroElektronika

Development tools - Books - Compilers

Software and Hardware

solutions for Embedded World

With useful implemented peripherals, plentiful practical code

examples and a broad set of additional add-on boards (ADC

potentiometer, two RS-232, RS485, Compact Flash, CAN etc.),

MikroElektronika development boards make fast and reliable

tools that can satisfy the needs of experienced engineers and

beginners alike.

USB

2.0 programmer

with on board

dsPICPRO

User’s Manual

dsPICPRO User’s Manual

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD 2

page

MikroElektronika

Development

tools

dsPICPRO

2.0

USB

No part of this manual, including the product and software described in it, may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into

any language in any form or by any means, except documentation kept buy the pur-

chaser for backup purposes, without the express written permission of

MikroElektronika company.

Product warranty or service will not be extended if the product is repaired, modified

or altered, unless such repair, modification or alteration is authorized in writing by

MikroElektronika.

MIKROELEKTRONIKA PROVIDE THIS MANUAL “AS IS” WITHOUT WARRANTY

OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PUROSE.

IN NO EVENT SHALL MIKROELEKTRONIKA, ITS DIRECTORS, OFFICERS,

EMPLOYEES OR DISTRIBUTORS BE LIABLE FOR ANY INDIRECT , SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES(INCLUDING DAMAGES FOR

LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUP-

TION OF BUSINESS AND THE LIKE) EVEN IF MIKROELEKTRONIKA HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATION AND INFORMATION CONTAINED IN THIS MANUAL ARE FUR-

NISHED FOR INTERNATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT

ANY TIME WITHOUT NOTICE , AND SHOULD BE CONSTRUED AS A COMMIT-

MENT BY MIKROELEKTRONIKA

MikroElektronika assumes no responsibility or liability for any errors or inaccuracies

that may appear in this manual, including the product and software described in it.

Product and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners benefit, without intent to infringe.

First edition

November

2005

dsPICPRO User’s Manual

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD 3

page

MikroElektronika

Development

tools

dsPICPRO

2.0

USB

CONTENTS

CONNECTING THE SYSTEM page 4

INTRODUCTION page 5

Power Supply and the Reset Circuit page 11

On-board USB programmer page 12

Jumpers page 7

Switches and their functions page 6

MCU card page 8

LEDs page 13

Push Buttons page 15

Graphic LCD page 18

LCD 2x16 page 20

RS-232 Communication page 22

CONTENTS

DESCRIPTION OF THE DEVELOPMENT SYSTEM page 6

DS1820 Digital Thermometer page 29

A-D Converter input page 30

Compact Flash page 36

D-A Converter output page 33

Direct port access page 34

CAN page 27

RS-485 Communication page 25

Real Time Clock (RTC) page 38

dsPICPRO User’s Manual

page

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD

dsPICPRO

2.0

USB

MikroElektronika

Development

tools

CONNECTING TTHE SSYSTEM

The development system box contains a development system, CD, USB cable and

serial cable.

The first thing to do is to take the system out of a box. Unpack the USB cable and

connect it to the PC. Please use USB ports from the back of the PC, with direct con-

tact to the motherboard.

Connect the USB cable to the dsPICPRO board.

The PC will start the procedure for installing the USB driver for the on-board USB

2.0 programmer. Follow the procedure from the document ‘ Installing Driver for

USB programmer’ and install the USB driver.

Copy dsPICFLASH2.exe file to the folder of your choice. You can find this file in

the dsPICFLASH folder on the CD.

Run and use dsPICFLASH2.exe as explained in the document ‘dsPICflash pro-

grammer’.

After these 5 steps, your dsPICPRO is installed and ready for use. You should try

to read a program from the chip or to load an example from the examples folder.

CONNECTING THE SYSTEM

Step no.1

Step no.2

Step no.3

Step no.4

Step no.5

dsPICPRO User’s Manual

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD 5

page

MikroElektronika

Development

tools

dsPICPRO

2.0

USB

INTRODUCTION

The dsPICPRO development system is a full-featured development board for

Microchip dsPIC microcontrollers. It has been designed to allow students and engi-

neers to easily exercise and explore the capabilities of dsPIC microcontrollers. It

allows dsPIC microcontrollers to be interfaced with external circuits and a broad

range of peripheral devices, allowing the user to concentrate on software develop-

ment.

Figure 1 illustrates the development board. On a silkscreen, there are identification

marks beside each component. These marks describe connections to the microcon-

troller, operation modes, and provide some useful notes. The need for additional

schematics is minimized as all the information is printed on the board.

INTRODUCTION

Figure 1. dsPICPRO development board

dsPICPRO User’s Manual

page

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD

dsPICPRO

2.0

USB

MikroElektronika

Development

tools

SWITCHES

The dsPICPRO development board features many peripherial devices. In order to

enable these devices before programming, you need to check if appropriate jumpers

or switches have been properly set.

Switches are devices that have two positions - ON and OFF, which have a role to

establish or break a connection between two contacts.

The first switch, SW1, is used to enable LEDs connected to ports RB_L, RB_H,

RD_L, RD_H, RF and RG. For example, if switch RB_L is OFF, all RB lower

LED’s will be turned off.

The switches SW2 and SW3 are used to enable connections between various

peripheral devices and microcontroller pins.

For example, SW2 and SW3, enables a connection between the microcontroller

pins and temperature sensor, programmable gain amplifier (PGA), real time clock

(RTC), RS-485 communication etc.

Switch is ON

Switch is OFF

432 5876

Figure 2.

Group of 8 switches Switches 1-6 are ON, and

other switches are OFF

dsPICPRO User’s Manual

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD 7

page

MikroElektronika

Development

tools

dsPICPRO

2.0

USB

JUMPERS

Jumpers, like switches, can break or establish a connection between two points.

Beneath the plastic cover of the jumper is a metal contact, which makes a connec-

tion when the jumper is placed between two disconnected pins.

Jumpers are used as a selector between two possible connections using a three pin

connector. As illustrated in Fig. 3, middle connector can be connected to the left or

right pin, depending on the jumper’s position.

Left line is selected

All lines are disconneced

Right line is selected

Figure 3.

Jumper as a

multiplexer

JUMPERS

dsPICPRO User’s Manual

page

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD

dsPICPRO

2.0

USB

MikroElektronika

Development

tools

MCU CCARD

The dsPICPRO development board have a 80-pin MCU Card as shown on the fol-

lowing picture:

MCU CARD

Figure 4. MCU Card

dsPICPRO User’s Manual

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD 9

page

MikroElektronika

Development

tools

dsPICPRO

2.0

USB

When you are placing MCU Card on the dsPICPRO MCU socket you must follow

these steps:

MCU CCARD

If there is already MCU Card

placed on dsPICPRO, you must

remove it by slowly pulling it up.

Label on the MCU Card must

be at the upper-left corner as it

is drawn on the dsPICPRO

board.

When MCU Card is on the place,

push it down by applying the

pressure on all edges at the same

time.

Step no.1

Step no.2

Step no.3

dsPICPRO User’s Manual

page

MIKROELEKTRONIKA SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD

dsPICPRO

2.0

USB

MikroElektronika

Development

tools

MCU CCARD

RB3

PortB low

vcc

8765432

LEDs RB_L

SW1

RG15

RC1

RC2

RC3

RC4

RG6

RG7

RG8

MCLR

RG9

Vss

Vdd

RA12

RA13

RB5

RB4

RB3

RB2

RB1

RB0

RC14

RC13

RD0

RD11

RD10

RD9

RD8

RA15

Vss

OSC2

OSC1/CLKI

Vdd

RG2

RG3

RF6

RF7

RF8

RF2

RF3

RB6

RB7

RA9

RA10

AVdd

AVss

RB8

RB9

RB11

Vss

Vdd

RB12

RB13

RB14

RB15

RD14

RD15

RF4

RF5

RG13

RG12

RG14

RA7

RA6

RG0

RG1

RF1

Vdd

Vss

RD7

RD6

RD5

RD4

RD13

RD12

RD3

RD2

RD1

dsPIC30FXXXX

RF0

RB10

RA14

vcc

The microcontroller’s pins are routed to various peripherials as illustrated in Fig.5. All ports have

direct connections to Direct Port Access connectors. Such connectors are typically used for con-

necting external peripherials to the board, or for providing useful points for connecting digital

logic probes.

All ports are connected to LEDs, push-button switches and pull-up/down resistors , which allow

for easy digital pin state monitoring and testing.

Some of the pins are connected to other peripherials such as the DS1820 temperature sensor, RS-

232 communication, LCD, etc.

Figure 5. System connection

Inhaltsverzeichnis

Andere mikroElektronika Mikrocontroller Handbücher

mikroElektronika

mikroElektronika EasyPIC5 Bedienungsanleitung

mikroElektronika

mikroElektronika Click Bedienungsanleitung

mikroElektronika

mikroElektronika Mikromedia MIKROE-608 Bedienungsanleitung

mikroElektronika

mikroElektronika Mikromedia PIC24EP Bedienungsanleitung

mikroElektronika

mikroElektronika mikromedia for dsPIC3 Bedienungsanleitung

mikroElektronika

mikroElektronika EasyPIC Fusion V7 TQFP PT MCU CARD 1 Bedienungsanleitung

mikroElektronika

mikroElektronika Ambient 2 click Bedienungsanleitung

mikroElektronika

mikroElektronika clickBOARD I2C isolator click Bedienungsanleitung

mikroElektronika

mikroElektronika CLICKER2 FOR PIC32MX Bedienungsanleitung

mikroElektronika

mikroElektronika CLICKER 2 STM32 Bedienungsanleitung

mikroElektronika

mikroElektronika RS232 click Bedienungsanleitung

mikroElektronika

mikroElektronika IrDA2 click Bedienungsanleitung

mikroElektronika

mikroElektronika dsPIC Ready3 Bedienungsanleitung

mikroElektronika

mikroElektronika ROTARY R click Bedienungsanleitung

mikroElektronika

mikroElektronika CLICKER 2 FOR FT90X Bedienungsanleitung

mikroElektronika

mikroElektronika Clicker 2 MIKROE-2800 Bedienungsanleitung

mikroElektronika

mikroElektronika MIKROE-1575 Bedienungsanleitung

mikroElektronika

mikroElektronika MIKROE-1993 Bedienungsanleitung

mikroElektronika

mikroElektronika clicker STM32 M4 Bedienungsanleitung

mikroElektronika

mikroElektronika MINI-M4 Bedienungsanleitung

mikroElektronika

mikroElektronika mikromedia for ARM Bedienungsanleitung

mikroElektronika

mikroElektronika mikromedia Series Bedienungsanleitung

mikroElektronika

mikroElektronika MSP432 clicker Bedienungsanleitung

mikroElektronika

mikroElektronika RS232 click Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

mikroElektronika dsPICPRO Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken