Millenium MPS-500 USB Bedienungsanleitung
MPS-500 USB
e-drum set
assembly instructions
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: [email protected]
Internet: www.thomann.de
17.07.2015, ID: 277656 (V2)
Table of contents
1 Safety instructions.......................................................................................................................................................................................................... 4
2 Contents of package....................................................................................................................................................................................................... 5
3 Assembly.............................................................................................................................................................................................................................. 6
4 Protecting the environment.................................................................................................................................................................................... 11
Table of contents
MPS-500 USB
3
1 Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.
Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke!
Never let children unattended use electrical devices.
Safety instructions
e-drum set
4
2 Contents of package
Before you assemble your kit, make sure the contents of package is complete according to the following list.
Millenium MPS-500 e-drum set
nMillenium MPS-500 e-drum module
nPads:
1 × 8" snare / stereo
3 × 8" tom / mono
1 × 8" kick
1 × 8" hi-hat
1 × 12" crash with choke function
1 × 12" ride
nOptical hi-hat controller
nDrum pedal
nRack with pad brackets
nComplete pad wiring
nMains adapter
Contents of package
MPS-500 USB
5
3 Assembly
Overview
Loosen the wing nuts on the holder clamps before inserting the tubes. Mount the various elements in the specified sequence.
The positions of the pads, cymbals, etc. are shown in the illustration below.
Setting up the rack
CAUTION!
Danger of cuts on hands and fingers
When plugging the connections, take care for sharp edges on the metal pipes, screws etc.
Assembly
e-drum set
6
1 Adjust the height of the holder clamps for the horizontal crossbar and three wing arms according to your pre‐
ferred playing position. Mount the horizontal crossbar and three wing arms and tighten the retaining screws.
2 Insert the two lateral supports into the holder clamps provided for this purpose. Make sure that the lower ends of
the supports are resting flush on the floor. Then tighten the retaining screws.
3 Position the holder clamps for the individual pads. Then tighten the retaining screws.
4 Turn the L-rods into a suitable position for mounting the pads. Then tighten the retaining screws.
5 Insert the crash pad, ride pad and hi-hat pad supports into the respective holder clamps on the rack. Secure the
supports at the desired vertical position using the retaining screws.
6 Loosen the retaining screws at the support joints and orient the supports so as to match your preferred playing
position. Then re-tighten the retaining screws.
Assembly
MPS-500 USB
7
Mounting pads on the rack
1. Attach the supplied L-pieces to the pads. First, tighten the wing nuts on the pads hand-tight.
2. Then slide the plastic ends of the L-pieces up to the stop into the designated terminals on the rack.
3. Align the pads on the rack to meet your needs, then tighten the wing nuts of the pad brackets and the bolts of the pad
terminals on the rack evenly.
Mounting cymbals on the rack
Assembly
e-drum set
8
1. Put the three cymbal holders as shown into the designated terminals on the rack.
2. Tighten the screws of the terminals firmly and evenly.
3. Unscrew the wing nuts (9) from the cymbal holders and take the felt washers (10) off the holders.
4. Place the cymbals on their supports as illustrated.
5. Put the felt washers (10) on top of the cymbals, and secure the pads on their supports using the respective wing nuts (9).
Make sure that the connector block on the underside of the cymbals is not stuck to the cylinder bolt of the counter-holder.
Mounting the drum module on the rack
1. Put the drum module up to the stop into the empty terminal of the left side arm.
2. Align the module and tighten the wing nut of the terminal.
Mounting the bass pedal
1. Snap the two metal rods into the holes provided on the frame of the pedal.
2. Place the beater into the hole provided on the rotary head of the kick drum pedal and tighten the clamp with the drum key
firmly.
Assembly
MPS-500 USB
9
Bass drum and hi-hat
1. Position the bass drum pad centred under the rack. Position the bass drum pedal centred in front of the pad.
2. Place the hi-hat pedal to the left of the bass drum pedal.
Set-up and cabling
Set up the rack, the pads and the cymbals according to your needs. As a final step, all triggers need to be wired to the drum
module. Note the labelling on the drum module and the colour markings of each cable.
Assembly
e-drum set
10
Andere Handbücher für MPS-500 USB
1
Inhaltsverzeichnis
Andere Millenium Trommel Handbücher
Millenium
Millenium MPS-850 Bedienungsanleitung
Millenium
Millenium HD-100 Bedienungsanleitung
Millenium
Millenium MPS-400 Bedienungsanleitung
Millenium
Millenium RT-1 Bedienungsanleitung
Millenium
Millenium MPS-250 USB Bedienungsanleitung
Millenium
Millenium DT-600 Bedienungsanleitung
Millenium
Millenium MPS-750X PRO Bedienungsanleitung
Millenium
Millenium MPS-150X Bedienungsanleitung
Millenium
Millenium MPS-500 USB Bedienungsanleitung
Millenium
Millenium DT-600 Bedienungsanleitung
