Millennium T3668-80 Einrichtungshandbuch

ABOVE GROU ND POOL SAFET Y

WARN I N G

FAILURE TO HEED THESE WARNINGS CAN RESULT IN PERMANENT INJURY,

PARALYSIS FROM A BROKEN NECK, ELECTROCUTION OR DROWNING.

THIS POOL IS NOT DESIGNED FOR DIVING OR JUMPING!

DANGEROUS INJURY CAN RESULT, SHALLOW WATER!

Your pool contains a large quantity of water, and is deep enough to present inherent dangers to lif

e and health unless the follow

ing safety rules are strictly observed. First-time users run the highest risk of injury. Make sure

everyone understands. To insure

your pool is used safely you

must

observe the following safety precautions:

NO JUMPING OR DIVING

The top rail of your pool is not a walkway and must not be used for jumping or diving.

Do not

permit jumping or diving into the pool from a deck or the top rail of the pool. Diving or jumping

into the pool can result in serious injury.

NEVER USE THE POOL ALONE

Never permit the pool to be used unless it is attended by at least one person other than the

bather. Someone should always be available to lend assistance in an emergency.

NEVER LEAVE CHILDREN UNATTENDED

Never leave a child alone and unsupervised in or near the pool—not even for a second. There

is no substitute for constant adult supervision.

NO ROUGH PLAY

Do not permit “rough-playin” in and around your pool. Surfaces can become slippery and

hazardous when wet.

LIGHT THE POOL AT NIGHT

If the pool is used after dusk, adequate lighting must be provided. Illumination in the pool area

must be sufficient to clearly judge pool depth and all features in and around the pool. For light

ing recommendations, consult your local licensed electrical contractor

RESTRICT ACCESS TO THE POOL

Do not leave chairs or other furniture beside the pool that could be used by a child to climb

up into the pool. Ladders must be removed whenever the pool is unattended. A fence with a

lockable gate around the pool or yard is strongly recommended and may be required by law in

some jurisdictions.

NO ALCOHOL OR DRUGS

Never drink alcoholic beverages or use any intoxicants which could hinder your judgment and

reflexes.

KEEP YOUR POOL CLEAN AND SANITARY

Your filter system will remove suspended particles from the water and the surface skimmer

will remove insects, leaves and other debris from the water surface. Use the correct pool

chemicals as directed to destroy harmful bacteria and prevent formation of algae. Remember,

unsanitary water is a serious health hazard.

The safety stickers must be installed as per following instructions. Failure to properly install wa

rning labels will void warranty.

Failure to mount these safety labels may subject you to substantial liability in case of injury. Th

ese warning are not to be re

moved under any circumstances! If they become discolored or fall off please request replacements wh

ich will be sent at no

charge.

FOLLOW ALL SAFETY INSTRUCTIONS

Read and follow all safety instructions packaged with pool, ladder, deck or any other accessory.

Additional pool safety publications can be obtained by contacting: The Association of Pool &

Spa Professionals (www.apsp.org)

IMPORTANT NOTICE READ BEFORE INSTALLATION!

KEEP OFF TOP LEDGES

Do not walk on top ledges. They can be slippery and they are not a walkway.

10.

POOL COVER SAFETY

The cover must have a tamperproof locking retainer cable that positions the cover around the

pool wall and keeps it securely in place.

Never allow anyone, especially small children on the

cover. Asphyxiation or drowning could result. When purchasing any pool cover, please consult a

swimming pool professional.

11.

ELECTRICAL HAZARD

Never touch or attempt to service electrical equipment, including the filter when your body and/

or the ground is wet.

Electrocution or permanent injury due to high voltage (120V AC) could

result. The pool should be bonded in accordance with Section 680-26 of the National Electical

Code. For further assistance contact your dealer or a local licensed electrician. Do not use pool

during electrical or rain storms.

12.

SAFETY ROPE & POLE

Keep a safety rope 1/4" by 50" with a flotation buoy with an outside diamter of 15".

Have ac

cessible in a prominent area by your pool

Keep a pole not less that 16 feet (4,88m) long with a

blunt or hook end available at pool side in case of emergencies.

POOL CHEMICALS

Do not place chlorine, chlorine tablets or sticks directly into skimmer, or winterize your pool wit

liquid chlorine.

Damage to the skimmer, pool liner and filter will result. Failure to obey this in

struction will void all component warranties. Always follow Chemical Manufacturer’s insturctions

when storing, handling and dispensing pool chemicals.

14.

CHECK FOR DAMAGE

Periodically check your pool and ladder components for damage and wear.

Be sure all screws

are in place. Replace all damaged or worn components and tighten all screws before you use

the pool, deck or ladders. At first sign remove rust and touch up immediately.

15.

POOL PARTS

Never modify the pool or accessories, or remove or drill holes in the pool, deck or ladder com

ponents unless instructed.

Your pool wall is made of thin metal, there is an inherent cut hazard

with metal so use gloves during installation. Always use Original Equipment Manufactured parts

for your replacement parts.

REMEMBER

WATCH

CHILDREN

PLACE SIGN ON

LINER ABOVE WATER

LINE, OPPOSITE ENTRY

TO POOL

PLACE SIGN ON

WALL NEXT TO

POOL ENTRY

12/11

ABOVE GROUND ROUND POOL INSTRUCTIONS

T3668-80

POOL ASSEMBLY AND INSTALLATION MANUAL

Monument Above Ground 52” Round Extruded Wall Pools

Note: Deck and fence accessories shown are optional.

THIS MANUAL EXPLAINS THE CORRECT METHOD TO ASSEMBLE YOUR NEW SWIMMING POOL. READ THESE INSTRUCTIONS AND

STUDY THE ILLUSTRATIONS. ALSO READ INSTRUCTIONS FOR ACCESSORIES SUCH AS FILTERS, LADDERS, ETC. PAY PARTICULAR

ATTENTION TO THE CAUTIONS ON THE FOLLOWING PAGES.

THE MANUFACTURER IS NO T AFFILIATED WITH ANY PROFESSIONAL POOL INSTALLER, THEREFO RE THE MANUFACTURER CANNO T

ASSUME RESPO NSIBILITY FO R ERRO RS IN THE INSTALLATIO N OF YOUR PO OL BY THE INSTALLER O R THE HO MEOWNER. IF Y OU

HAVE THIS PO OL INSTALLED BY O THERS, PLEASE SUPERVISE TO BE SURE Y OUR POOL IS INSTALLED PRO PERLY AND THAT ALL

THE CAUTIO NS LISTED THRO UGHOUT THIS MANUAL HAVE BEEN FOLLOWED. PAST EXPERIENCE O R SHO RT CUTS MAY NO T BE

COMPATIBLE WITH OUR POOLS, FOLLOW THE INSTALLATION MANUAL.

THE MANUFACTURER RESERVES THE RIGHT TO CHANGE OR IMPRO VE ANY ITEM WITHOUT INCURRING ANY OBLIGATION TO MAKE

ANY CHANGES OR IMPROVEMENTS ON ITEMS PREVIOUSLY SOLD AND TO DISCONTINUE MODELS OR CHANGE SPECIFICATIONS AT

ANY TIME WITHOUT NOTICE.

THIS PRODUCT IS SOLD WITH A "LIMITED WARRANTY ". THE TERMS AND CONDITIONS ARE SET FORTH IN THE "LIMITED WARRANTY "

CERTIFICATE PACKED WITH EACH POOL. COPIES OF THE "LIMITED WARRANTY" ARE ALSO AVAILABLE UPON WRITTEN REQUEST.

YOUR LO CAL BUILDING CO DE MAY REQ UIRE O BTAINING A BUILDING PERMIT AND MAY HAVE REQUIREMENTS ON SETBACKS,

BARRIERS, ETC. ANY HO ME BUILT O R PREFABRICATED DECKS SH OULD CONFORM TO THE LOCAL CODES, AND BOCA NATIONAL

BUILDING CODE. THE ELECTRICAL CODE MAY REQUIRE A PERMIT AND INSPECTIO N, AND USE O F G FCI DEVICES O R O THER

CONDITIONS. THE ELECTRICAL INSTALLATION MUST ALSO CONFORM TO ARTICLE 680 OF THE NATIONAL ELECTRIC CODE. INSTALL

THE FILTER AND PUMP IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS. . ARTICLE 680 STATES THAT YOU MUST

BOND THE SWIMMING POOL PUMP TO THE SWIMMING POOL. THIS CAN BE DONE BY ATTACHING A #8 COPPER WIRE FROM THE

BONDING LUG ON THE PUMP TO AN UNPAINTED METAL SURFACE ON THE POOL WALL OR BOTTOM CLIP.

THE INSTALLATION OF AN ABOVE GROUND SWIMMING POOL WILL USUALLY REQUIRE THREE PEOPLE TO HELP ASSEMBLE IT.

DANGER: THIS POOL, EVEN IF SUPPLIED WITH A DEEP AREA, CONFORMS TO THE NATIONAL SWIMMING POOL INSTITUTE

STANDARDS FOR A TYPE O, NON-DIVING POOL. DIVING, SLIDING OR JUMPING INTO THE POOL MAY CAUSE PARALYSIS, DEATH OR

PERMANENT INJURY.

DANGER

1. DO NOT DIVE OR JUMP INTO Y OUR POOL. DO NOT USE A POOL SLIDE ON THIS POOL. YOUR POOL CONTAINS SHALLOW WATER

AND IS NOT DESIGNED FOR HEADFIRST ENTRY (DIVING OR SLIDING) OR JUMPING. DIVING, SLIDING OR JUMPING CANRESULT IN A

BROKEN NECK IF YOU STRIKE THE POOL. THIS CAN RESULT IN PARALYSIS, DEATH OR PERMANENT INJURY . INFORM ALL FAMILY

AND GUESTS OF THESE RULES AND POINT OUT WARNING LABELS.

2. IT IS NECESSARY TO MAINTAIN A 4’ HIGH BARRIER TO REDUCE THE CHANCE OF A CHILD ACCESSING AN UNSUPERVISED POOL.

THE BARRIER MAY BE A FENCE, WALL, OR COMBINATION TH EREOF WHICH COMPLETELY SURROUNDS THE POOL. BARRIERS

MUST COMPLY WITH THE LOCAL BUILDI NG CODE, BOCA NATIONAL BUILDING CO DE OR THE “CONSUMER PRODUCT SAFETY

COMMISSION” BARRIER STATEMENT. THE FO UR FOOT HIG H PO OL WALLS USUALLY PROVIDE THIS BARRIER, HOWEVER IF THE

POOL IS LESS THAN 48” ABO VE GRADE, OR HAS BUTTRESSES (OVAL POOLS), YOU MAY NEED ADDITIONAL FENCING TO PROVIDE

THIS BARRIER. CONSULT WITH Y OUR BUILDING O FFICIAL FO R SPECIFIC REQ UIREMENTS. FENCING O PTIONS ARE AVAILABLE

FOR YOUR POOL, PLEASE CONTACT YOUR POOL DEALER.

3. Y OU MUST MAINTAIN A 5’ WIDE “CLEAR ZONE” AROUND TH E POOL AND DECK OR FENCING. DO NOT ALLOW TOYS, CHAIRS,

TABLES OR SIMILAR CLIMBABLE OBJECTS IN THIS “CLEAR ZO NE”, ENABLING CHILDREN TO CLIMB AND G AIN ACCESS TO THE

POOL. THE FILTER EQUIPMENT MUST ALSO BE LOCATED OUTSIDE OF THE “CLEAR ZONE”.

4. YOU MUST RAISE AND LATCH, OR SECURE YOUR POOL LADDER OR POOL ENTRANCE WHEN THE POOL IS NOT IN USE.

Adherence to the above items will reduce the frequency of preventable child drownings in swimming pools.

WARNING

1. YOUR POOL IS SUPPLIED WITH WARNING SIGNS, WHICH MUST BE AFFIXED TO THE POOL AS SPECIFIED. IF YOU BUILD A DECK,

THE TWO AREA SIGNS MUST BE AFFIXED TO THE DECK AT THE POINT OF ENTRY, VISIBLE TO PEOPLE ENTERING THE POOL

AREA. FAILURE TO INSTALL OR IMPROPER LOCATION OF SAFETY INFORMATION WILL SUBJECT YOU AND/OR THE INSTALLER

TO LIABILITY ARISING FROM INJURY CLAIMS.

A. NO DIVING COPING: ( TWO SUPPLIED ) THESE ARE TO BE INSTALLED ACROSS THE POOL FROM THE POINT OF ENTRY,

AND HAVE ONE SECTION OF REGULAR COPING BETWEEN THEM.

B. COPING WITH INTERNATIONAL LOGO: THIS ONE COPING IS TO BE INSTALLED AT THE POINT OF ENTRY, EITHER ADJACENT

TO THE “A” LADDER, UNDER THE IN POOL LADDER, OR IN THE CENTER OF A DECK.

C: DANGER AREA SIGN WITH LOGO: ( T1440) THIS SIGN MUST BE INSTALLED AT THE POINT OF ENTRY, FACING ALL USERS

AS THEY ENTER THE PO OL. IF Y OUR POOL HAS A FENCE, THE SIG N IS TO BE FASTENED TO THE FENCE, ADJACENT TO

THE LADDER OR ENTRANCE. IF Y OUR POOL DOES NOT HAVE A DECK O R FENCE, ATTACH THE SIGN TO THE EDGE OF THE

COPING ADJACENT TO THE LADDER. THE SIGN MUST BE VISIBLE TO ALL USERS AS THEY ENTER THE POOL AREA.

D. CAUTION - SAFETY RULES SIGN: (1445) THIS SIGN MUST BE ATTACHED TO THE FENCE DIRECTLY BELOW THE DANGER

SIGN OR IF YOU DO NOT HAVE POOL FENCING, ON THE COPING NEXT TO THE DANGER SIGN.

If any signs are missing or damaged contact the customer service department for replacements.

CAUTION

1. DECK SURFACES MAY BECOME SLIPPERY WHEN WET. DO NOT RUN OR DIVE INTO THE POOL FROM THE DECK.

NOTE: SUNTAN LOTIONS AND OILS MAY CAUSE POOL COMPONENTS TO BECOME SLIPPERY.

2. EACH MONTH CHECK THE POOL WALL FOR DETERIORATION OR LEAKAGE, ESPECIALLY AT THE SKIMMER AND RETURN

FITTINGS. THE SKIMMER AND RETURN GASKETS SHOULD BE REPLACED EACH SPRING TO PREVENT LEAKAGE.

DETERIORATION CAN WEAKEN THE POOL WALL WHICH COULD RUPTURE, RELEASING THE POOL WATER WHICH COULD CAUSE

BODILY HARM AND PROPERTY DAMAGE.

3. FOR NIGHTIME USE, YOU MUST PROVIDE LIGHTING TO ILLUMINATE THE POOL, SAFETY SIGNS, AND DECK SURFACES. LIGHTING

MUST COMPLY WITH ARTICLE 680 OF THE NATIONAL ELECTRIC CODE. IT IS IMPORTANT THAT USERS BE ABLE TO SEE THE

SHALLOW DEPTH OF THE POOL AT ALL TIMES.

4. THE FOLLOWING BASIC LIFESAVING EQUIPMENT MUST BE ON HAND AT ALL TIMES:

A. A LIGHT BUT STRONG POLE ( SHEPHERD’S CROOK ) NOT LESS THAN 12’ LONG.

B. A 1/4” THROWING ROPE, AS LONG AS 1 1/2 TIMES THE MAXIMUM WIDTH OF THE POOL, WHICH IS ATTACHED TO A COAST

GUARD APPROVED FLOTATION DEVICE SUCH AS A RING BUOY.

C. A TELEPHONE SHOULD BE NEARBY WITH A LIST OF EMERGENCY TELEPHONE NUMBERS, SUCH AS POLICE, & AMBULANCE

5. ADDITIONAL POOL SAFETY RELATED PUBLICATIONS ARE AVAILABLE FROM THE FOLLOWING:

ASSOCIATION OF POOL & SPA PROFESSIONALS CONSUMER PRODUCT SAFETY COMMISSION

2111 EISENHOWER AVE. WASHINGTON, DC 20207

ALEXANDRIA, VA 22314-4695

IMPORTANT INSTALLATION ITEMS

1. LEVELNESS; POOL MUST BE LEVEL WITHIN 3/4”. UNLEVEL POOLS PLACE EXTREME FORCES ON THE POOL WHICH MAY DEFORM.

2. WALL CLOSURE; THE POOL WALL MUST BE FASTENED TOGETHER PROPERLY WITH BOTH BARS AND FASTENERS IN ALL HOLES.

OMITTED BARS OR FASTENERS CAN CAUSE THE WALL TO RUPTURE, DESTROYING THE POOL AND INJURING PEOPLE.

3. SAND COVE; THIS SUPPORTS THE LINER AND MUST BE PACKED SOLID. IF IT COMPRESSES, SHIFTS OR ERODES THE LINER MAY

RUPTURE, RELEASING ALL THE WATER AND DESTROYING THE POOL AND INJURING PEOPLE.

4. THESE POOLS ARE NOT DESIGNED TO BE BURIED. THE GROUND FORCES CAN COLLAPSE THE POOL INWARD. FOR SEMI IN-

GROUND INSTALLATIONS, CONTACT YOUR DEALER FOR DOCUMENT T3964.

5. DO NOT LOCATE YOUR POOL NEAR STRUCTURES SUCH AS A HOUSE, GARAGE, ETC. AS PEOPLE COULD DIVE OR JUMP INTO

THE POOL RESULTING IN DEATH OR PERMANENT INJURY.

6. ALTHOUGH THERE ARE RELATIVELY FEW PARTS IN YOUR POOL, NONE MAY BE OMITTED IN ASSEMBLY. EACH PART SUPPLIED

IS AN IMPORTANT PART AND IF OMITTED, MAY CAUSE POOL FAILURE. CHECK ALL PARTS AGAINST THE PARTS LIST.

WARNING: Do not exceed the following torque values for the noted fasteners:

1/4” - 20 S. S. Fasteners 75 (in. lbs.)

3/8” - 16 S. S. Fasteners 236 (in. lbs.)

3/8” - 16 Aluminum Fasteners 143 (in. lbs.)

TOOLS AND MATERIALS

PHILLIPS SCREWDRIVER #2 HAND TROWEL EXTENSION CORD HAMMER RAKE

SLOTTED SCREWDRIVER #2 GARDEN HOSE & NOZZLE STRING LINE PLIERS

SOCKET WRENCH & SOCKETS 50’ TAPE MEASURE HAND TAMPER TORQUE WRENCH

TRANSIT OR FARM LEVEL ELECTRIC DRILL & BITS GARDEN SHOVEL WRENCHES

1 LONG STRAIGHT 2 X 4 14’ LONG 1 ROLL DUCT OR FABRIC TAPE

25 WOOD STAKES I CAN WHITE SPRAY PAINT

SAND AND BLOCK CHART SAND 2” x 8” x 16” 4” x 8” x 16”

POOL SIZE TONS YARDS PATIO BLOCKS CAP BLOCKS

15' 2 1 1/4 10 NOTE: Sand must be

masons or bar sand and

be free of foreign objects

18' 2 1/2 1 3/4 12

21' 3 1/2 2 1/4 14

24' 4 1/2 3 16

27' 5 3/4 3 3/4 18

30’ 6 5 20

SELECTING THE POOL SITE

1. Check your local building codes and acquire proper building permits. For poor soil conditions consult a

professional engineer.

2. The pool site must be absolutely level and solid. The area must be free from stones and roots.

3. To protect the pool from chemicals and foreign matter in the soil, you may use a ground cover under the sand

base.

Do not install your pool on asphalt, tar paper, grass, wood, gravel, clay, or concrete, or treated soils.

4. Position your pool away from trees, overhead wires, structures such as a house or garage or septic field.

GROUND PREPARATION

Your pool must be installed on a solid level surface. Posi tion stakes as shown on figure 1 and use a farm level or

transit to level the area shown. Remove all grass, roots and stones. Start at the lowest spot level outwards, do not fill

in low spots. The area must be absolutely level. The following table refers to Figures 1 and 3 on the next page.

ROUND POOLS LINE “1” LINE “2”

15’ - 0” 8’ - 6” 7’ - 6”

18’ - 0” 10” - 0” 9’ - 0”

21’ - 0” 11’ - 6” 10’ - 6”

24’ - 0” 13’ - 0” 12’ - 0”

27’ - 0” 14’ - 6” 13’ - 6”

30’ - 0” 16’ - 0” 15’ - 0”

SECTION II - POOL CONSTRUCTION

Step 3: See Figures 3 and 4. Place the required amount of s and in the pool area. Starting at the bottom clip on the

downwind side of the pool, attach the upright slat to the bottom clip. Be sure the machine screw is to the inside of the

pool. Working in a counter clockwise direction slide a wa ll slat onto the upright slat. The wall slat should be held

about 30 degrees from the upright slat wh ile sliding together. Then when seated, rotate the wall slat against the wall

angle. The skimmer slat should be located between the fi rst two round side upright slats as you work around the

pool. Do not locate the skimmer under the patio. The return slat must be located within 15 panels to the left of the

skimmer as you face the pool.

Be careful not to let the wall fall over during assembly. The walls must remain plumb. If the wall falls over,

disassemble fallen section and start again.

After the pool wall is assembled, check the dimensions of the pool to insure that it has not shifted during assembly.

Step 4: See Figure 5 and Detail 5a. Install the skimmer throat gasket to each side of the pool wall and attach the

skimmer to the wall as shown using hardware provided with the skimmer. Mount the skimme r at the center with only

two (2) pan head screws at this point. Refer to skimmer instruction sheet.

Loosen the nuts from the bottom clip / upright slat attachment. If you are installing a walk deck on this pool

Do Not completely remove the nut from the bolt. You will need this bolt to attach the walk deck posts.

CAUTION: Installation of the wall in any other

manner than precisely described above will cause

extensive damage to the pool and may result in

injury or death to those people in or around your

pool.

FIGURE 2

FIGURE 1

STAKE L00033A

LINE 2

LINE 1 LEVEL

Step 1: Parts Identification:

See figures in bill of material

packet. Check for

installation addendums.

Step 2: See Figure 1 and

2. Mark line “2” as shown in

the table on page 3. Create

a circle on line “2” by sliding

the wall channels into the

bottom clips. Place a 2”

thick patio block under each

bottom clip. If the bottom

wall channel is on soft

ground, place additional

blocks in a pyramidal shape

under the bottom clips for

support. Also place

additional blocks under the

wall channel where needed.

Dig 2” down for each block.

The top of the top block

must be at grade level.

Place a stake adjacent to

each wall channel to keep

the circle in position during

installation.

GROUND

PREPARATION AREA:

REMOVE ALL GRASS,

ROOTS, STONES AND

DEBRIS

TRANSIT

L00034A

SMALL

BOTTOM

CLIP

FOLLOW LINE 2

STAKE 2” X 8” X 16”

PATIO BLOCK

BOTTOM WALL

ANGLE

STACKING

PATTERN FOR

POOR SOIL

If a pool fence or deck is to be installed, read those manuals before proceeding. Check care

and maintenance manual for proper placement of safety information.

Step 5: See Figure 6. Spread the sand across the entire botto m of the pool. Moisten and tamp the sand to provide

a solid base. The sand base must be 2” deep after tampi ng. The sand should be moistened and trowel to a smooth

finish. Create a 6” radius cove along the wall as shown. This cove must also be tamped solid to prevent shifting.

WARNING: Failure to use the sand or sand equivalent and shape it as specified will void all warranties on the pool

and liner.

FIGURE 3

W00036

DIMENSIONS

ARE TO TOP

OF WALL

WALL

CHANNEL

50”

44”

”

RADIUS

”

SAND BASE

FIGURE 6

W00026B

NOTE: THE SKIMMER

THROAT GASKET MUST

SANDWICH THE WALL. I.E.

ONE FLAP OF THE GASKET

MUST BE ON THE INSIDE OF

THE WALL AND THE OTHER

ON THE OUTSIDE.

FIGURE 4

W00037

WALL SLAT

UPRIGHT

SLAT

SMOOTH SIDE

AGAINST

14” – 20 SS

HEX NUT

BOTTOM

CLIP

¼” – 20 X ¾” SS

MACHINE SCREW

WALL ANGLE

WALL SLAT

ROTATE INTO

PLACE

BOTTOM CLIP

UPRIGHT

SLAT

W00040

SKIMMER

DETAIL 5A THROAT

GASKET

WALL

BEADED LINERS

Step 6: See Figure 6. Place the bead receiver on the wall. Tape the joints of the bead receiver using fabric

tape to protect the liner. Place the top clips on the upright s. Attach the top clips to the uprights as shown in

figures 7 and 7A.

Step 7: Remove the liner from the carton and unfold into the pool. Be careful not to drag, abrade or snag

the liner. Spread the liner out over the entire botto m of the pool. Raise the liner side wall and place the

bead into the bead receiver. See Figure 6. Bead must be fully seated in the receiver to prevent it from

coming out later. When filling begins, check the bead frequently.

NOTE: If the liner is exposed to the sun for a long time , it will stretch and cause wrinkles. This can be

avoided by waiting until dusk or by spraying cold water on the liner during installation.

Step 8: Smooth all the wrinkles out on the bottom of the liner. To remove wrinkles, always pull the liner

firmly but gently. No sharp tugs ! Be certain liner is centered. Time spent removing wrinkles and aligning

the liner will give you a neater looking and easily maintained pool.

TOP CLIP BEAD

#10 CAPTIVE

DUCT TAPE NUT RECEIVER

FIGURE 7A

BEAD

RECEIVER

LINER

BEAD

LINER

WALL

L00036C

#12 X ½” HEX

HEAD SCREW

4 PER UPRIGHT

(USE LOWER

SET OF HOLES

IN TOP CLIP)

UPRIGHT

FIGURE 7 SLAT

FIGURE 6 A00031

W00023 WALL SLAT

Step 9: Begin to fill the pool with water. Use a slow st ream of water and fill approximately 1 1/2” deep. Make

sure the fit of the liner is correct, smooth out any wrinkles in the pool bottom. If installing a deck, do not fill

more than 12” until the deck is installed.

Step 10: Fill the pool with 4” to 6” of water.

WARNING: The pool must not be more than 3/4” out of level. If the pool is not level, drain the water and

level the structure. Any non-compliance with this requirement will void all warranties.

Step 11: Locate the safety warning copings as described and as shown at the back of this manual. Attach the

coping, as shown in figure 8, to the outermost set of holes in the top clip. Measure the distance from the coping

to the water surface at several points around the pool to be certain that the pool is still level.

Step 12: At each upright, attach the coping covers as shown in Figures 9A and 9B based on the type of pool

you are installing.

Step 13: Fill the pool until the water level is 3 inches below the return hole.

Step 14: Follow the instructions for the f iltration system, skimmer and return that are supplied with the filter.

See Figure 10 for a reference only.

COPING COVER ATTACHMENT FOR ALUMINUM POOLS

#10 X ½” SELF

TAPPING SCREWS ATTACH COPING TO

OUTER SET OF HOLES

ROUND END

COPING

FIGURE 8

W00053

TOP CLIP

ALUMINUM POOLS

WITH ALUMINUM COVERS

COPING

COVER

#10-24 X 5/8”

MACHINE SCREW

UPRIGHT

SLAT

BEND TABS TO

SECURE TO

COPING

ALUMINUM POOLS

WITH RESIN COVERS

FIGURE 9A

A00028A

#12 X 1”

HEAX HEAD

SCREWS

ONE PER SIDE

#10-24 X 5/8”

MACHINE

SCREW

FIGURE 9B

A00028B

POOL WALL

SKIMMER ASSEMBLY

TEFLON

TAPE

TEFLON TAPE LINER

HOSE

ADAPTER

FACE PLATE

GASKET

HOSE

ADAPTER

FIGURE 10 FACE

PLATE

SCREW

LOCKNUT

FACE

PLATE

W00024

FIBER

WASHER LINER

SANDWICH

GASKET POOL WALL

RUBBER GASKET

WALL FITTING

DIRECTIONAL BALL DIRECTIONAL

BALL FITTING

(POINT OPENING AWAY

FROM SKIMMER)

RETURN ASSEMBLY

DANGER: When a filter or any other electrical device is added to this pool, it is the responsibility of the

purchaser to take all necessary precautions as set forth in article 680 of the National Electrical Code and

local electrical codes. Failure to comply with th is requirement may result in a dangerous or hazardous

electrical condition, which may cause bodily injury or death.

B POOL

WITH “A”

FRAME

LADDER

AND

FRNCE

FIGURE 11A

POOL WITH

LADDER DSA00004

NOTE: Refer to Page 2, Warning section for Label Number Designations

Step 15: Attach the remaining safety warning signs as described and shown in Figures 11A and 11B. If

installing a fence or deck refer to those manuals for proper placement of safety information.

Step 16: Fill the pool up to the center of the skimmer, make sure that all fasteners are tightened properly

and your pool is correctly assembled. Please read the “Sensible Way to Enjoy Your Pool” booklet and

enjoy years of swimming and relaxation.

WATER SIDE

DANGER

C & D

DANGER

CAUTION:

DECK SIDE POINT OF

ENTRY C & D

A A

SA00003B

FIGURE 11B

ADDITIONAL DANGER SIGN

(SEE SIDE DECK MANUAL)

B C & D

POINT OF

ENTRY

POINT OF

ENTRY

WARNING: After completion of the pool, the pool must never be drained to less than 1/2 full. Damage

to the structure and/or liner ma

result.

Inhaltsverzeichnis

Andere Millennium Schwimmbad Handbücher

Millennium

Millennium T3669-80A Einrichtungshandbuch

Beliebte Schwimmbad Handbücher anderer Marken

Piscine Solide

Piscine Solide V35018 Bedienungsanleitung

Bestway

Bestway STEEL PRO 56545 Bedienungsanleitung

Bestway

Bestway 52385E Bedienungsanleitung

GardiPool

GardiPool Quatroo 300x500 Bedienungsanleitung

Vogue

Vogue V31039 Bedienungsanleitung

Intex

Intex PureSpa SC-10 Bedienungsanleitung

Intex

Intex 128912GH Bedienungsanleitung

GRE

GRE KPCOR60 Bedienungsanleitung

GRE

GRE Marbella Bedienungsanleitung

Intex

Intex 126384GS Bedienungsanleitung

Piscine Solide

Piscine Solide V35038 Bedienungsanleitung

Coleman

Coleman Power Steel 90387E Bedienungsanleitung

Wilbar

Wilbar Mediterranean V35041 Bedienungsanleitung

GRE

GRE PBT201 Bedienungsanleitung

Endless Pools

Endless Pools SwimCross Bedienungsanleitung

GRE

GRE Vermela Bedienungsanleitung

Polygroup

Polygroup Funsicle Oasis Pool Bedienungsanleitung

GRE

GRE Mango Bedienungsanleitung