Miller 481 Bedienungsanleitung

www.millertripods.com

IMPORTANT

Please read this Operator’s Manual carefully•

and thoroughly before using the pedestal

Please retain this Operator’s Manual for future•

reference

COMBINATION PEDESTAL

Operator’s Manual

Including Dolly options & accessories

FEATURES AND CONTROLS

1 100mm Bowl 13` Air Pressure Set Knob

2 Bowl Brackets 14 Safety Valve

3 Steering Wheel 15 Schrader Valve

4 Central Piece Bowl Unit 16 Air Pressure Block

5 Locking Screws Bowl Unit 17 Column Clamp Handle

6 Inside Column Pedestal 18 Dolly Centre Hub

7 Clamp System Column 19 Dolly Arm

8 Spider Clamp Ring 20 Dolly End Ball

9 Outside Column 21 Tracking Lock (only for #483)

10` Spider Leg 22 Dolly Wheel Brake

11 Spider Foot 23 125mm Caster Wheel

12 Base Piece Column 24 Cable Guard

Fig 1.

INTRODUCTION

Thank you for purchasing the Miller Combination Pedestal. These instructions

give you a full mounting description and short information about the main func-

tions of the Combination Pedestal Column and the range of Miller Studio Dollies.

The Combination Pedestal combines design and affordability into a flexible new

Camera Support System available from your Miller dealer.

OPERATION MANUAL

Please read this manual carefully prior to using the Combination pedestal. Do

not omit any steps.

The manual contains important set-up, camera mounting information and should

be read in conjunction with the operating manuals of the fluid head and camera

you have chosen to complement your Combination pedestal.

SET-UP

These instructions build the Combination Pedestal Column on the Miller Studio

Dolly range in the most commonly used way.

NORMAL SET-UP:

Deploy Miller Studio Dolly and rotate dolly arms to locking position. Place the•

dolly on flat surface. (Fig 2.&3.)

Fig 2. Fig 3.

SET-UP (CONT)

Peel off Miller label (if applicable) from the dolly•

centre hub to reveal the 12.5mm hole. (Fig 4.)

Remove Pedestal Column and Spider Legs from•

the packing box.

Line up Column to the dolly centre hub, insert M12•

bolt into the 12.5mm hole. (Fig 5.&6.)

Tighten the bolt but not fully with the supplied•

10mm Hexagon Key.

Align the Spider Foot on to the ball of dolly end•

(Fig 7.). Pull the Rubber Stirrup up and over the

end shoulder of Spider Foot. (Fig 8.) Repeat for the

remaining two spider legs.

Fully tighten the bolt and check that the Column is•

secure.

Raise and lock the (airless) Pedestal Column in the•

highest position using the Column Clamp Handle.

Use a High Pressure Pump and connect it to the•

Schrader Valve on the Air Pressure Block. (Fig 9.)

Fig 4.

Fig 5.

Using pump bring the air pressure to the desired level

depending on the camera load that is going to be used.

During detaching of the pump there is some air leaving

the system, therefore, we recommend putting extra air in

the system and let some air out when fine tuning balance

of the camera with its accessories.

Now the Combination Pedestal is set up in its standard

configuration on the Miller Studio Dolly range.

Fig 7.

Fig 8.

Fig 6.

Fig 9.

SET-UP (CONT)

EXTENDED SET-UP (optional)

The Pedestal can be enlarged using the optional VPS-300 extension (Fig 10.). This

will extend the base height of your pedestal by 300mm.

Placing Extension:

• Removethethreelockingscrewsthatholdthecolumninthebasepieceusing

the supplied hexagon key.

• TakeofftheColumnwithspiderandlayitaside.

• Mounttheextensionyouneedusingthesamehexagonkey.

Take the Column and mount it on top of the extension.•

Fig 10.

Loosen the Spider Clamp Ring•

with the two locking screws and let

it slide down until the spider legs

fit the ball of dolly end. Then

fasten the Spider Clamp Ring

again with both screws.

MOUNTING THE VIDEO CAMERA

• Beforemountingcamera,besurethatColumnClampHandleistightandthe

wheels are locked.

• PlacethePedestalonastableandflatfloor.

• MountyourFluidHeadonthe100mmbowl.Whenusinga75mmHeada#378

100/75 bowl adaptor is available from your Miller dealer.

• MountthecameratotheFluidHeadusingthequickreleasecameraplate.

Apply all appropriate accessories to the camera up to the maximum of 30kg

total load (camera, head & accessories together). Refer to the Operator’s

Manual of the Fluid Head.

• IfnecessaryusethePumptoincreasepressuretotheairsystemorusethe

Set Knob to decrease the pressure. Use the complete vertical stroke of the

Pedestal Column to test what is the ideal situation.

• Iftoomuchairpressureisappliedthesafetyvalvewillopenandairwill

escape from the system to prevent it from being overloaded.

Fig 11. Fig 12.

LOW SET-UP ON DOLLY (Fig 11.)

• RemovethethreelockingscrewsthatholdtheBowlUnitontheinsidecolumn

using the supplied hexagon key.

• TakeofftheBowlUnitandlayitaside.

• Removethethreelockingscrewsthatholdthecolumninthebasepieceusing

the supplied hexagon key.

• TakeofftheColumnwithspiderandlayitaside.

• Mount,ifnecessarytheextensionyouneedusingthesamehexagonkey.Fix

them firmly but do not use too much force for there is a chance of damaging

the tool or the screws.

• TaketheBowlunitandmountitontopoftheextensionordirectlytotheBase

Piece of the Dolly.

• AspeciallowsetupispossibleusingonlytheBowlunit,placingitonitsrub-

ber feet on the ground or a table (Fig 12.).

SET-UP (CONT)

The Miller Studio Dolly range has all the strength and smooth flowing dolly

movesrequiredforstudioapplications.TheMillerStudioDollyrangehasrein-

forced centre hub with collapsible box tubing arms. New, smooth action castors

ensure the Miller Studio Dolly range offers sturdy, smooth support under all

Miller ENG and HD tripods.

Miller Combination Pedestal can be set up on the Miller Sudio Dolly range

available with #480, #481 and #483.

MILLER STUDIO DOLLY RANGE

#480 #481 #483

Cat# 480 481 483

Description Studio Dolly Studio Dolly with cable guards Studio Tracker Dolly

Weight 6.2 kg (13.7 lb) 6.6 kg (14.6 lb) 6.9 kg (15.2 lb)

Folded length 610 mm (24.0 in) 610 mm (24.0 in) 640 mm (25.2 in)

Wheel Diameter 125 mm (4.9 in) 125 mm (4.9 in) 125 mm (4.9 in)

Diameter open 1072 mm (42.2 in) 1072 mm (42.2 in) 1072 mm (42.2 in)

Tube type Alloy Alloy Alloy

SPECIFICATIONS

SERVICE AND SALES SUPPORT

Height Range

Normal Set-up: 900 mm - 1255 mm

(fluid head not included)

Extended Set-up: 1200 mm - 1555 mm

(utilizing VPS-300)

Stroke: 355 mm

Weight:

Combination Column: 6.3 kg

Extension: 0.8 kg

Maximum Load: 30 kg

Miller Authorised Service Agents must carry out all service and repair work

onMillerPedestal.Failuretoobservethisrequirementmayvoidwarranty.It

is advisable to notify Miller or a Miller Authorised Service Agent if a change of

performance is observed as a result of impact or rough usage. For information

regarding sales and service of Miller products, or for your nearest Miller repre-

sentative, please contact us via our websie or at the following:

MILLER CAMERA SUPPORT (Australia) MILLER CAMERA SUPPORT LLC (USA)

30 Hotham Parade, Artarmon, Sydney 216 Little Falls Road, Cedar Grove

NSW 2064 Australia New Jersey 07009-1231 USA

Tel: +61 2 9439 6377 Tel: (973) 857 8300

Fax: +61 2 9438 2819 Fax: (973) 857 8188

Email: sales@miller.com.au Email: [email protected]

MILLER FLUID HEADS (Europe) LTD.

Unit A2, Ford Lane Industrial Estate

Ford Lane, Ford, West Sussex

BN18 0DF United Kingdom

Tel: +44 (0) 1243 555 255

Fax: +44 (0) 1243 555 001

Email: [email protected]

WEBSITE

www.millertripods.com

D5125-1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miller Kamerazubehör Handbücher

Miller

Miller 1055 Bedienungsanleitung

Miller

Miller skyline 90 Bedienungsanleitung

Miller

Miller DS-60 Fluid head Bedienungsanleitung

Miller

Miller DS5 Bedienungsanleitung

Miller

Miller Tripod Bedienungsanleitung

Miller

Miller Rapidlock SOLO 100 Bedienungsanleitung

Miller

Miller 1090 Compassx 2 Bedienungsanleitung

Miller

Miller Solo-Q 2500 Bedienungsanleitung

Miller

Miller Compass XV2 Fluid Head Bedienungsanleitung

Miller

Miller 16 CB PLUS CiNX 3 Bedienungsanleitung

Miller

Miller DS10 Bedienungsanleitung

Miller

Miller Arrow Fx 16 CB Plus Series Bedienungsanleitung

Miller

Miller 1576 Bedienungsanleitung

Miller

Miller TRIPOD SERIES Bedienungsanleitung

Miller

Miller 1036 Bedienungsanleitung

Miller

Miller Compass 25 Bedienungsanleitung

Miller

Miller Projib 711 Bedienungsanleitung

Miller

Miller 1501 Bedienungsanleitung

Miller

Miller Compass 12 Fluid Head Bedienungsanleitung

Miller

Miller compass 15 Bedienungsanleitung

Miller

Miller 1025 Bedienungsanleitung

Miller

Miller Compass 23 Bedienungsanleitung

Miller

Miller HD Tripod Series 100 Bedienungsanleitung

Miller

Miller 1050 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung

Custom Brackets

Custom Brackets Digital PRO-M Bedienungsanleitung

Vivo

Vivo MOUNT-LT01C Bedienungsanleitung