Miller Dynasty 280 Bedienungsanleitung

OWNER’S MANUAL

OM-265 411D 2015−05

Dynasty)− Maxstar)280

Dynasty)− Maxstar)210

Automation Expansion

Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.

Read the safety information at the beginning of the manual and in each section.

1-1. Software Expansion

.A software update is required to ensure proper

operation of all purchased feature expansions.

For instructions to download TIG Software up-

dates, see PDF file F269272A on software ex-

pansion memory card.

Card Requirements:

.Purchased software expansion memory card

required.

1 MemoryCard Port

2 Indicator LED

Enabling Software Expansion:

Insert card containing software expansion into port.

LED indicator blinks green while machine is reading

from or writing to the card. After successfully read-

ing from or writing to the card, the LED switches

from blinking green to continuous green. The ma-

chine is now ready to use software expansion. Do

not remove card while LED is blinking green.

.Softwareexpansion card must remain in mem-

ory card port to enable software expansion.

Disabling Software Expansion:

Remove the software expansion card from the

memorycard port.

Troubleshooting:

Problem: Indicator LED is continuous red.

Remedy: Remove and reinsert card. If problem

continues,the card is bad. Contact Factory Autho-

rized Service Center for a replacement card.

The memory card port uses an SD memory card.

The SD Logo is a trademark of the SD-3C LLC

Company.

AutomationExpansion − Enabling the automation software expansion configures Remote 14 socket I for valid arc and socket J for arc length control,

and the ability to configure socket E as an input for Output Enable (Weld Stop) in Dynasty and Maxstar 210 and 280 Models.

Additional Parts Required: Plug and pins required to connect to the Dynasty or Maxstar 210 and 280 Remote 14 receptacle can be obtained from

MillerElectric Mfg. Co. Parts Dept. :Order Part No. 141 162 − Housing Plugs + Pins (service kit), and install according to instructions provided with

the kit.

1-2. Automation Remote 14-Socket E

TECH

RMT

14-E

123.See ADVANCED MENU FUNCTIONS in the Dynasty/Maxstar

280’s Owner’s Manual or Dynasty/Maxtar 210 Owner’s Manual for

additionalinformation on Accessing Tech Menu options.

The [14-E] option is before [MACH] [RSET], replacing the existing

[EXPC] option.

1 Parameter Display

2 Setting Display

3 Encoder

Rotate Encoder to adjust parameter setting.

[14-E] Remote - Remote14-Socket E input can be configured for the following:

[RMT] − Remote Controls − Select when using typical Miller remote amperage controls such as: RFCS - 14 HD Foot Control, or RCC -14

Remote Contactor and Current Control

[EXPC] − External Pulse Control − Select when it is desired to control machine amperage from an external source. A command voltage of

0−10 volts DC equals 0 (off) − maximum amperage.

[STOP] − Output Enable (weld stop) − Select to remotely stop the weld outside the normal weld cycle.

Remote 14 socket E connection to socket D must be maintained at all times to enable output. If connection is broken, output stops,

postflow begins, and AUTO STOP is displayed on the meters.

OM−265 411 Page 2

1-3. Remote 14 Receptacle Information

805 497-A

BKI

CLNH

DMG

Socket Socket Information

15 VOLTS DC

OUTPUT

CONTACTOR

AContactorcontrol +15 volts DC, referenced to G.

BContact closure to A completes 15 volts DC

contactor control circuit and enables output.

REMOTE

OUTPUT

CONTROL

COutput to remote control; +10 volts DC output to

remote control.

DRemote control circuit common.

E0 to +10 volts DC input command signal from

remote control.

*Reconfigurable as input for Output Enable (Weld

Stop) − used to remotely stop the weld outside the

normal welding cycle. Connection to the D socket

must be maintained at all times. If the connection

is broken, output stops, and Auto Stop is dis-

played.

Output

Signals

FCurrent feedback; +1 volt DC per 100 amperes.

HVoltage feedback; +1 volt DC per 10 volts output.

I* Valid arc indication closed to socket G with valid

arc. Electrical specifications: open collector tran-

sistor (see Section 1-4 for connection example).

J* Arc length control lockout closed to socket G dur-

ing Initial and Final Amperage and Slope, and dur-

ing the background time of a <=10 Hz pulse wave-

form. Electrical specifications: open collector tran-

sistor (see Section 1-4 for connection example).

COMMON GReturn for all output signals: F, H, I, J and A.

CHASSIS K Chassis

Serial

Communication

Bus

L** Modbus Common (RS485 Common)

M** Modbus D1 (RS485 B+)

N** Modbus D0 (RS485 A-)

.If a remote hand control, like the RHC-14, is connected to the Remote 14 receptacle, some current value above min. must be set on the remote

control before the Panel or Remote contactor is turned on. Failure to do so will cause current to be controlled by the panel control, and the remote

handcontrol will not function.

*Available with optional Automation Expansion memory card.

**Available with optional Modbus Expansion memory card. Modbus serial communication provides access to all front panel parameters and

machinefunctionality. See Owner’s Manual 265415 for a list of Modbus registers. Modbus expansion also includes functionality of Automation

and AC Independent Amplitude (Dynasty only) Expansions.

Sockets G and K are electrically isloated from each other.

1-4. Simple Automation Application

CR1 +

−

CR1 To User Equipment

Coil resistance plus R

should be chosen to

limit current to 75 mA

User supplied power

up to 27 volts DC

peak

Pin I, J: Collector

Pin G: Emitter

Andere Handbücher für Dynasty 280

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miller Schweißsystem Handbücher

Miller

Miller Millermatic 212 Auto-Set Bedienungsanleitung

Miller

Miller INTEGRA 183 Bedienungsanleitung

Miller

Miller Bobcat 200 Air Pak Bedienungsanleitung

Miller

Miller MTX 3502 ROBOT GUN Bedienungsanleitung

Miller

Miller Continuum 350 Bedienungsanleitung

Miller

Miller Trailblazer 325 Diesel Bedienungsanleitung

Miller

Miller DYNASTY 200 DX Bedienungsanleitung

Miller

Miller FieldPro Remote CE Bedienungsanleitung

Miller

Miller AA40GB w/OCP Bedienungsanleitung

Miller

Miller ST 44 Series Bedienungsanleitung

Miller

Miller MAC TOOLS MW 183ET Bedienungsanleitung

Miller

Miller PipePro XC Bedienungsanleitung

Miller

Miller Deltaship 502 Bedienungsanleitung

Miller

Miller INFINITY 35 Bedienungsanleitung

Miller

Miller Roughneck C-4015S Bedienungsanleitung

Miller

Miller XMT 300 CC Bedienungsanleitung

Miller

Miller PipeWorx 400 Bedienungsanleitung

Miller

Miller WDW100 Bedienungsanleitung

Miller

Miller XMS 403 Bedienungsanleitung

Miller

Miller Legend 302 Bedienungsanleitung

Miller

Miller SUITCASE 12RC CE Bedienungsanleitung

Miller

Miller Subarc AC/DC 1000 Bedienungsanleitung

Miller

Miller D-74DX Bedienungsanleitung

Miller

Miller D-74 MPa Plus Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung