Miller EnPak A60GBHW Bedienungsanleitung

A60GBHW

Quick Start Guide

Service Locations

Engine Filters

and Fill Points

Fuel Pump

Hydraulic Pump

Compressor

Filters and

Fill Point

Remote/Manual

Switch

CB-1 Location

Cool Pak CB

Location

Fuse and Relay

Panel

Brush Location

Serial Number

Location

2 31 14 4 8

READ INSTRUCTIONS.

• Read and follow all labels and the Owner’s Manual carefully before installing, operating or

servicing unit. Read the safety information at the beginning of the manual and in each section.

WARNING

Control Panel

Start Button

Home Screen

Adjust Control/Select Button

Turning On Unit

Safety interlock signal must be provided to turn unit on. Refer to

section 5-8 in Owner’s Manual for more information.

Press the Start button to turn the Control Panel on. A splash screen

will display for a few seconds before the Home screen is displayed.

Press the Start button to turn on the engine. Use the soft buttons to

open the Weld, Battery, and Settings screens.

Turning Off Unit

Press the Start button to turn the unit off.

Turning Off Control Panel

Hold the Start button for 2 seconds to turn the control panel off.

Control panel will display “Shutting Down” and turn off after a few

seconds along with stopping the engine if running.

3 1

Top Status Bar

Status Bar Text

Displays user feedback and any active alerts

and errors.

Glow Plug Icon

Lit when the glow plugs are activated before

cranking.

Auto Start/Stop Icon

Lit when Auto Start/Stop is enabled.

Gauges

RPM Gauge

Displays engine RPM. When unit is stopped,

“OFF” is highlighted. When unit is Auto

Stopped, “READY” is highlighted.

Air Compressor PSI Gauge

The MIN and MAX air compressor PSI

settings are indicated by tick marks.

Chassis Power Gauge

When Chassis Power is not providing output,

gauge shows chassis battery voltage.

If unit is not running, Auto Start/Stop is

enabled, and chassis battery voltage drops

below 12.3 volts, the unit will Auto Start.

When Chassis Power is providing output,

gauge shows chassis power amperage

output.

Engine Load Gauge

Displays current load on the engine. When

gauge reads near or above max, the engine

power is maxed out.

Hydraulics Gauge

Displays hydraulic output (hydraulic

units only).

Battery Charge Gauge

Displays battery charge current output.

Bottom of gauge shows whether the unit is

in 12V or 24V mode.

When output is above 100A, “BOOST”

illuminates.

Soft Buttons

Weld Operation Button

Opens the Weld screen (weld units only).

Battery Charge Operation Button

Opens the Battery Charge screen. On the

Battery Charge screen, the user can start

and stop battery charge and change

12V/24V operation.

Air Compressor Operation Button

Turns air compressor On or Off.

Settings Button

Press to access System Settings,

Maintenance, and System Info screens.

Settings Menu

System Settings

Select to change unit operation parameters.

Maintenance Menu

Select to check, change, or reset the

maintenance interval schedule.

System Info

Select to check and update software, check

and download summary file, and restore unit

to factory defaults.

Troubleshooting

Displays live unit data for troubleshooting

purposes.

Home Screen

1 2 3

4 5 6

10 11 12 13

To Change System Settings

Step 1: Rotate Adjust Control/Select button to select a setting.

Step 2: Press Adjust Control/Select button on desired setting.

Step 3: Rotate Adjust Control/Select button to update the setting.

Step 4: Press Adjust Control/Select button to

save the setting, or press the Back button to discard setting change.

Press HOME button to return to Home screen.

Air Compressor Operation

Air Compressor Operation Button

While in the Home screen and the Weld screen, press

the Air Compressor Operation button to toggle the

compressor output.

Compressor is On when AIR icon is white, and Off when

AIR icon is gray.

NOTE: Weld output and generator power may be reduced when the air

compressor is on.

System Settings

System Settings Item Selectable Item Options Description

Power Priority – Optimizes output priority between hydraulics and air compressor.

Air Pressure Min 90 psi up to 10 psi less than max pressure Minimum pressure to start air compressor (adjustable in 1 psi increments).

Air Pressure Max 175 psi down to 10 psi greater than Maximum pressure to stop air compressor (adjustable in 1 psi increments). Lower is better to conserve

min pressure engine power.

Air Response Low, Medium, High Optimizes the response when a heavy air load is applied instead of waiting to turn the air compressor

on when the minimum psi threshold is met.

Auto Start/Stop Enabled / Disabled Engine will stop when no load is applied for the Auto Start/Stop Time threshold. Engine will start again

NOTE: Enabled is recommended. when a load is applied.

Auto Start/Stop Time 2 to 30 minutes How long the unit will run before Auto Stopping with no load.

RPM Auto Idles at 1800 rpm and adjusts based on demand.

2800 Locked at 2800 rpm.

Screen Brightness 1 to 10 Changes the brightness of the display.

Hydraulic Max Pressure 2000 to 4000 psi Maximum hydraulic pressure set point.

NOTE: Compensator is factory set to 3300 psi. If setting maximum pressure above 3300 psi factory setting, a Factory Authorized Service agent will

need to adjust compensator.

Hydraulic Max Flow 3 to 20 gpm NOTE: Set to 8 gpm for most cranes. Maximum hydraulic flow set point. Never set hydraulic flow higher than crane rating.

Crane Remote Type 0V to 12V Step Chooses crane remote signal type.

0V to 12V Proportional

12V to 0V Proportional

Crane Voltage Threshold 0.1V to 12V Optimizes voltage threshold for OFF vs ON.

NOTE: If unit does not idle down •For "0V to 12V Step" and "0V to 12V Proportional" crane remotes, set Crane Voltage Threshold to 0.1V.

when all loads are off, increase the •For IMT Cranes, set Crane Voltage Threshold higher than 0.1V to allow unit to idle down when crane

Crane Voltage Threshold slightly is not enabled.

until unit idles down. •For "12V to 0V Proportional" crane remotes, set Crane Voltage Threshold to slightly less than 12V.

Tap To Start (Weld Units Only) Enabled / Disabled Enabled: Restarts engine while in Auto Stop mode by tapping welding rod to workpiece.

NOTE: Enabled is recommended. Disabled: Engine does not restart by tapping welding rod.

Safe Start Enabled / Disabled Enabled: When in weld screen or battery charge mode, unit will automatically switch to Chassis Power

NOTE: Enabled is recommended. when chassis battery voltage drops below 12.3 volts.

Disabled: Unit does not automatically switch to Chassis Power.

Power Time 1 to 20 minutes Adjustable timeout for automatic switch to Chassis Power.

MillerWelds.com

Maintenance

Service Intervals

Change service intervals or reset interval

countdown here.

The Maintenance screen displays engine

and compressor hours for the unit and

allows the user to reset oil change hours

and change the interval (only shorter than

recommended).

Hours Before Next Oil Change

Required For Each Component

Press the Home button to go to the Home

screen. Press the Back button to go to the

Menu screen.

Label located under the top cover.

Service intervals, filters and filter kit part

numbers are all listed here for reference.

Additional information and details are

available in the owner’s manual.

Record Serial Number Of Your Unit

Contact your Upfitter for service or questions.

Upfitter

Service Contact

Phone

Maintenance Label

Andere Miller Schweißsystem Handbücher

Miller

Miller I-22 Bedienungsanleitung

Miller

Miller Millermatic 251 Bedienungsanleitung

Miller

Miller Syncrowave 180 SD Bedienungsanleitung

Miller

Miller Gold Seal GS-250 Bedienungsanleitung

Miller

Miller GA-4OGL Bedienungsanleitung

Miller

Miller Millermatic 210 Bedienungsanleitung

Miller

Miller Big Blue Duo Air Pak 800X Bedienungsanleitung

Miller

Miller SGA 100 Bedienungsanleitung

Miller

Miller XR-AlumaPro Series Bedienungsanleitung

Miller

Miller MigMatic 220 Bedienungsanleitung

Miller

Miller Millermatic 251 Bedienungsanleitung

Miller

Miller Trailblazer 302 Diesel Bedienungsanleitung

Miller

Miller Auto Invision II Bedienungsanleitung

Miller

Miller Bobcat 200 Air Pak Bedienungsanleitung

Miller

Miller Millermatic 212 Auto-Set Bedienungsanleitung

Miller

Miller AlumaPower 350 MPa Auto-Line CE Bedienungsanleitung

Miller

Miller XMT 425 MPa Auto-Line CE Bedienungsanleitung

Miller

Miller SRH-333 Bedienungsanleitung

Miller

Miller Auto Invision 2 Bedienungsanleitung

Miller

Miller LMSW-52 Bedienungsanleitung

Miller

Miller RAD-400 Bedienungsanleitung

Miller

Miller Millermatic 251 Bedienungsanleitung

Miller

Miller SDX-575 Bedienungsanleitung

Miller

Miller 907431002 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung