MINN KOTA TALON Bedienungsanleitung

FOOT SWITCH

Owner's Manual

Compatible with all Bluetooth®enabled Talons.

INTRODUCTION

SER NO S365 MK12345

EXAMPLE

NOTICE: The serial number on your Talon Foot Switch is

located on the reverse side of the switch from the buttons.

If the Foot Switch is attached to the Pedestal, remove the

Foot Switch from the Pedestal to see the serial number.

THANK YOU

Thank you for purchasing the Talon Foot Switch. Intuitive features and wireless control lets you easily raise and lower the Talon spike.

Control up to two Talons – independently or simultaneously – from this Bluetooth®enabled waterproof switch. Hands free control lets

you focus on ﬁshing.

Model:__________________________________________________________________________________________________________________

Serial Number: __________________________________________________________________________________________________________

Purchase Date: __________________________________________________________________________________________________________

Store Where Purchased:___________________________________________________________________________________________________

REGISTRATION

Remember to keep your receipt and immediately register your

Talon Foot Switch. To receive all the beneﬁts of your product

warranty please ﬁll out and mail the registration card. You may

also register your product online at minnkotamotors.com.

SERIAL NUMBER

Your Minn Kota 11-character serial number is very important. It

helps to determine the speciﬁc model and year of manufacture.

When contacting Consumer Service or registering your product,

you will need to know your product’s serial number. We

recommend that you write the serial number down so that you

have it available for future reference.

NOTICE: Do not return your Talon Foot Switch to your retailer. Your retailer is not authorized to repair or replace this unit. You

may obtain service by calling Minn Kota at (800) 227-6433 or returning your Talon Foot Switch to the Minn Kota Factory Service

Center. Please include proof of purchase, serial number and purchase date for warranty service.

TALON FOOT SWITCH INFORMATION (For Consumer Reference Only)

minnkotamotors.com | 3

SAFETY CONSIDERATIONS

Please thoroughly read the user manual. Follow all instructions and heed all safety considerations. Use of this product is only permitted

for persons that have read and understood these instructions. Minors may use this product only under adult supervision.

WARNING

You are responsible for the safe and prudent operation of your boat or vessel, and Talon(s). This product does not relieve you from the

responsibility of safe operation of your boat. It may be hazardous to operate your Talon in rough or turbulent water conditions, such

as fast currents or changing environmental conditions. Do not deploy your Talon if these conditions are present, especially when the

underwater topography is unknown. Failure to follow this warning may result in unexpected operation or failure of the Talon to operate

or anchor and could cause death or serious injury. You must avoid hazards to anchoring and always maintain a permanent watch so you

can maintain proper control of your boat. You must always be prepared to regain manual control of your boat. Learn to operate your

Minn Kota product in an area free from hazards and obstacles.

WARNING

The Talon should be disconnected from the power source when it is not in use or is off the water. Always disconnect the Talon from

battery(s) before cleaning or checking the Talon. In the event of unexpected operation, remove power leads from the battery.

WARNING

Take care that neither you nor other persons approach the Talon Spike too closely while operating, neither with body parts nor with

objects. The Talon is powerful and may endanger or injure you or others. While the Talon is operating, watch out for persons swimming

and for ﬂoating objects. Persons who lack the ability to run the Talon or whose reactions are impaired by alcohol, drugs, medication, or

other substances are not permitted to use this product.

WARNING

It is recommended to only use Johnson Outdoors approved accessories with your Talon. Using non-approved accessories including

those used to mount or control your product may cause damage, unexpected operation and injury. Be sure to use the product and

all approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected operation. Keep

all factory installed parts in place including motor, electronic and accessory covers, enclosures and guards. Failure to adhere to this

warning may affect your warranty.

CAUTION

Never leave the boat unattended with the Talon as your only boat anchor. Talon is not intended to provide primary anchorage.

FEATURES

NOTE: Speciﬁcations subject to change without notice. This diagram is for reference only and may diﬀer from your

actual Foot Switch.

Auto Down

Button/Pairing

Button

Auto Up Button/

Pairing Button Anchor

Mode Button

Talon Selection Button /

Work Light Button

Talon Selection Indicator LEDs

Anchor Mode

Selection LED

minnkotamotors.com | 5

INSTALLATION

INSTALLING THE TALON FOOT SWITCH

Your new Talon Foot Switch comes complete with all of the hardware you’ll need to install it directly to the deck of your boat. Please

review the parts list, mounting considerations and tools needed for installation prior to getting started.

INSTALLATION PARTS LIST

Item /

Assembly Part # Description Qty.

A2994153 ASSEMBLY, TALON 3 FT SWITCH 1

22383455 SCREW-#8 X 1.0" PPH TY AB SS 3

4sQUICK REFERENCE GUIDE 1

6sINSTALLATION INSTRUCTIONS 1

✖This part is included in an assembly and cannot be ordered individually.

sNot shown on Parts Diagram.

Before mounting your Talon Foot Switch, please give consideration to the following:

1. Examine your boat to ensure that you will not drill into any obstructions and that the hardware will be accessible for assembly.

2. Make sure the area under the mounting location is ﬂat, clear to drill holes and that the installation hardware will not damage

existing components below the mounting surface. It may be necessary to shim or modify the mounting surface under the mounting

location to create a ﬂat area for the Foot Switch Pedestal to be mounted.

3. Mount the Talon Foot Switch in an area that has a clear line of communication with the Bluetooth enabled Talon(s) it is intended to

control for optimum performance.

4. Mount the Talon Foot Switch in an area where it will not become a tripping hazard.

MOUNTING CONSIDERATIONS

• Pencil or similar marking tool

• Drill

• #2 Phillips Driving Bit

TOOLS AND RESOURCES REQUIRED

INSTALLING THE FOOT SWITCH

Installing the Foot Switch

a. Review the Mounting Considerations to determine

an acceptable mounting location. Once a location

is selected, take the Talon Foot Switch Assembly

(Item #A) and remove the Pedestal from the Base by

squeezing the Tabs on both sides of the Foot Pedal

and pulling the Foot Switch and Pedestal apart.

ITEM(S) NEEDED

#A x 1

NOTICE: The Pedestal comes attached to

the Foot Switch and needs to be removed for

installation.

Foot Switch

Pedestal

Marked Location

Mounting Holes

Pads

Pedestal (top)

Pedestal (bottom)

Tab

INSTALLATION

b. The Pedestal has three Mounting Holes that are

used to secure it to the boat. The bottom side of the

Pedestal has three Pads around the Mounting Holes.

These Pads should be placed down, towards the boat

when the Pedestal is installed. Position the Pedestal

at the selected location and mark the Mounting

Holes with a pencil or similar marking tool.

minnkotamotors.com | 7

INSTALLING THE FOOT SWITCH

Mounting Holes

Pedestal

d. Once the Pedestal is installed, take the Foot Switch

and reattach it to the Pedestal. Make sure the Tabs

on the Foot Switch click into place and the Foot

Switch is fully seated on the Deck of the Boat.

c. Double check the Mounting Location. Take the

Screws (Item #2) and place one each in the

Mounting Holes of the Pedestal. Make sure the

Mounting Holes line up with the Marked Locations

and then use a Drill with #2 Phillips Driving Bit to

secure the Pedestal to the Deck of the Boat. Do not

over-tighten.

ITEM(S) NEEDED

#2 x 3

Deck of Boat

Screws Pedestal

Tab

Foot

Switch

Tab

INSTALLING THE FOOT SWITCH

a. Retract the anchor on the Talon by pressing the Up

button on the Talon Indicator Panel.

b. Once the Talon is fully retracted, press and hold the

Up button and the Down button on the Foot

Switch at the same time until all of the LED's at the

top of the Foot Switch begin to scroll. Then release

them.

c. Immediately press and hold the Up button

and the Down button simultaneously on the

Indicator Panel. The Depth Indication LEDs on the

Indicator Panel of the Talon will begin to scroll. Once

the LEDs are scrolling release the buttons on the

Indicator Panel. The Talon and Foot Switch will go

into Pairing Mode for 20 seconds. If a signal with

three fast beeps occurs, the Talon and Foot Switch

have successfully paired. If 20 seconds pass while

in Pairing Mode and they do not successfully pair, an

error tone will sound indicating that the pairing was

not successful, and the Foot Switch will not be able

to control the Talon.

d. If the Pair is unsuccessful, repeat the process.

Up Button

Down Button Indicator

Panel

11a

Talon Foot Switch

Auto Down

Button/Pairing

Button

Auto Up Button/

Pairing Button

Anchor Mode

Selection LED

Talon Selection

Indicator LEDs

Pairing a Foot Switch to a Single Talon

In order to Pair a Foot Switch to the Talon, please be sure to ﬁrst

Pair the Talons together. When two Bluetooth Talons are paired

together, the Foot Switch that was paired to an individual Talon

will operate both Talons. Please see the "Pairing Two Talons and

Programming the Mounting Location" section of the Talon Owner's

Manual. If the two Talons are already paired together, a Foot Switch can be paired to either Talon. When the pairing process is

complete, the Foot Switch will be able to control both Talons.

Pairing a Foot Switch to Two Talons

NOTICE: For instructions on how to pair two Talons and

assign their Port and/or Starboard mounting locations,

please refer to your Talon owners manual.

minnkotamotors.com | 9

USING THE FOOT SWITCH

Anchor Mode Button

Used to select between Standard Mode, Soft

Bottom Mode and Rough Water Mode.

Auto Up/Auto Down Buttons

& Pairing Buttons

Used to deploy, retract or pause the anchor on the

Talon. Also used to pair the Remote to a Talon.

Talon Selection Button /

Work Light Button

Used to select the Port, Starboard, or both Talons.

Used to toggle the Work Light "on" and "off" and

switch between the different Work Light colors and

intensities.

Talon Selection Indicator LEDs

When 2 Talons are paired in the system, the right

LED is lit when the Starboard Talon is selected and

the left LED is lit when the Port Talon is selected.

Both the right and left arrows are lit when both

Talons are selected. When only one Talon is paired,

the lights will toggle, but the selection will control

the only paired Talon. When a selection is made, the

LEDs will stay lit for 1 second and then turn off.

Anchor Mode Selection LED

The Center LED ﬂashes red and green and then turns

off for Standard Mode. The center LED will be lit

green for Soft Bottom Mode and lit red for Rough

Water Mode. When in Soft Bottom Mode and Rough

Water Mode, the LED will stay lit for 1 second and

then turn off.

Auto Down

Button/Pairing

Button

Auto Up Button/

Pairing Button

Anchor

Mode Button Talon Selection Button/

Work Light Button

Talon Selection Indicator LEDs

Anchor Mode

Selection LED

CONTROLLING THE TALON WITH THE FOOT SWITCH

USING THE FOOT SWITCH

The Talon Selection button toggles the Talon that the Foot Switch is controlling, when 2 Talons are installed on the boat. The

selection toggles between a Talon mounted on the Port or Starboard side of the boat, or it can control both Talons at the same time.

The Talon Selection Indicator LED's are lit based on the selection made.

a. To toggle the Talon selected, press the Talon

Selection button, repeatedly until the desired

Talon is selected.

b. When the button is pressed, one or both of the

Talon Selection Indicator LEDs will be lit. If the

Foot Switch is oriented so the LEDs are facing away

from you, the arrow on the right will be lit when the

Starboard Talon is selected. If the arrow on the left is

lit, the Port Talon is selected. If both arrows are lit,

both Talons are selected.

Selecting a Talon to Operate with the Foot Switch

NOTICE: The Talon will always remember the last

selection made unless the Talon loses power.

NOTICE: When two Talons are paired to the Foot

Switch, it is possible to control them individually.

Therefore, the Talons may be in different states of

deployment.

Talon

Selection

Button

Talon Selection

Indicator LEDs

Talon Foot Switch

Port Starboard

Andere Handbücher für TALON

Inhaltsverzeichnis

Sprachen:

Andere MINN KOTA Schalten Handbücher

MINN KOTA

MINN KOTA 1810258 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung