Minolta QMS PageWorks/Pro 1100 Bedienungsanleitung

PageWorks/Pro 1100

PageWorks/Pro 1100L

SERVICE MANUAL

Trademark Acknowledgments

PageWorks™ is trademark of Minolta in the U.S. and Canada.

PagePro™ is trademark of Minolta in Europe, Japan and Asia.

Fine-ART and Fine Micro Toning are trademarks of Minolta Co., Ltd.

QMS and the QMS logo are registered trademarks of QMS, Inc.

PCL is a registered trademark of Hewlett-Packard Company.

Centronics is a registered trademark of Centronics Inc.

MS-DOS, Microsoft, Windows, and Windows NT are registered trademarks of

Microsoft Corporation.

IBM is a registered trademark of International Business Machines Corporation.

All other brand or product names are trademarks or registered trademarksof their

respective companies or organizations.

Safety Precautions for Inspection and Service

When performing inspection and service procedures, observe the following precautions to

prevent accidents and ensure utmost safety.

✽Depending on the model, some of the precautions given in the following do not apply.

Different markings are used to denote specific meanings as detailed below.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury. It may also be used to

alert against unsafe practices.

The following graphic symbols are used to give instructions that need to be observed.

Used to call the service engineer attention to what is graphically represented

inside the marking (including a warning).

Used to prohibit the service engineer from doing what is graphically represented

inside the marking.

Used to instruct the service engineer to do what is graphically represented inside

the marking.

1. Always observe precautions.

2. Before starting the procedures, be sure to unplug the power cord.

3. Use the specified parts.

WARNING

CAUTION

WARNING

• Parts requiring special attention in this product will include a label containing the

mark shown on the left plus precautionary notes. Be sure to observe the pre-

cautions.

• Be sure to observe the “Safety Information” given in Operator’s Manual.

• This product contains a high-voltage unit and a circuit with a large current

capacity that may cause an electric shock or burn.

• The product also contains parts that can jerk suddenly and cause injure.

• If this product uses a laser, laser beam leakage may cause eye damage or

blindness.

• For replacement parts, always use the genuine parts specified in the manufac-

turer’s Parts Manual. Installing a wrong or unauthorized part could cause dielec-

tric breakdown, overload, or undermine safety devices resulting in possible

electric shock or fire.

• Replace a blown electrical fuse or thermal fuse with its corresponding genuine

part specified in the manufacturer’s Parts Manual. Installing a fuse of a different

make or rating could lead to a possible fire. If a thermal fuse blows frequently,

the temperature control system is probably of a problem and action must be

taken to eliminate the cause of the problem.

4. Handle the power cord with care and never use a multiple socket.

5. Be careful about the high-voltage parts.

6. Do not keep your hands wet when performing the procedures.

7. Do not touch a high-temperature part.

8. Make a ground connection at all times (This item may not be effected in USA).

9. Do not remodel the product.

10. Restore all parts and harnesses to their original positions.

• Do not brake, crush or otherwise damage the power cord. Placing a heavy

object on the power cord, or pulling or bending it may damage it, resulting in a

possible fire or electric shock.

• Do not use a multiple outlet to which any other appliances or machines is con-

nected.

• Be sure the power outlet meets or exceeds the specified capacity.

• A part marked with the symbol shown on the left carries a high voltage. Touch-

ing it could result in an electric shock or burn. Be sure to unplug the power cord

before servicing this part or the parts near it.

• Do not unplug or plug in the power cord, or perform any kind of service or

inspection with wet hands. Doing so could result in an electric shock.

• A part marked with the symbol shown on the left and other parts such as the

exposure lamp and fusing roller can be very hot while the machine is energized.

Touching them may result in a burn.

• Wait until these parts have cooled down before replacing them or any surround-

ing parts.

• Be sure to connect a ground wire to the ground terminal even when performing

an inspection or repair. Without proper grounding, electrical leakage could result

in an electric shock or fire.

• Never connect the ground wire to a gas pipe, water pipe, telephone ground wire,

or a lightning conductor.

• Modifying this product in a manner not authorized by the manufacturer may

result in a fire or electric shock. If this product uses a laser, laser beam leakage

may cause eye damage or blindness.

• To promote safety and prevent product damage, make sure the harnesses are

returned to their original positions and properly secured in their clamps and sad-

dles in order to avoid hot parts, high-voltage parts, and sharp edges, or being

crushed.

• To promote safety, make sure that all tubing and other insulating materials are

returned to their original positions. Make sure that floating components mounted

on the circuit boards are at their correct distance and position off the boards.

iii

1. Precautions for Service Jobs

2. Precautions for Servicing with Covers and Parts Removed

3. Precautions for Working Environment

4. Precautions for Handling Batteries

CAUTION

• A toothed washer and spring washer, if used originally, must be reinstalled.

Omitting them may result in contact failure which could cause an electric shock

or fire.

• When reassembling parts, make sure that the correct screws (size, type) are

used in the correct places. Using the wrong screw could lead to stripped

threads, poorly secured parts, poor insulating or grounding, and result in a mal-

function, electric shock or injury.

• Take great care to avoid personal injury from possible burrs and sharp edges on

the parts, frames and chassis of the product.

• When moving the product or removing an option, use care not to injure your

back or allow your hands to be caught in mechanisms.

• Wherever feasible, keep all parts and covers mounted when energizing the

product.

• If energizing the product with a cover removed is absolutely unavoidable, do not

touch any exposed live parts and use care not to allow your clothing to be

caught in the moving parts. Never leave a product in this condition unattended.

• Never place disassembled parts or a container of liquid on the product parts fall-

ing into, or the liquid spilling inside, the mechanism could result in an electric

shock or fire.

• Never use a flammable spray near the product. This could result in a fire.

• Make sure the power cord is unplugged before removing or installing circuit

boards or plugging in or unplugging connectors.

• Always use the interlock switch actuating jig to actuate an interlock switch when

a cover is opened or removed. The use of folded paper or some other object

may damage the interlock switch mechanism, possibly resulting in an electric

shock, injury or blindness.

• The product must be placed on a flat, level surface that is stable and secure.

• Never place this product or its parts on an unsteady or tilting workbench when

servicing.

• Provide good ventilation at regular intervals if a service job must be done in a

confined space for a long period time.

• Avoid dusty locations and places exposed to oil mist or steam.

• Avoid working positions that may block the ventilation port of the product.

• Replace a rundown battery with the same type as specified in the manufac-

turer’s parts manual.

• Before installing a new battery, make sure of the correct polarity of the installa-

tion or the battery could burst.

• Dispose of used batteries according to the local regulations. Never dispose of

them at the user’s premises or attempt to try to discharge one.

5. Precautions for Laser Beam (Products Employing Laser Only)

• Removing the cover marked with the following caution label could lead to possi-

ble exposure to the laser beam, resulting in eye damage or blindness. Be sure

to unplug the power cord before removing this cover.

• If removing this cover while the power is ON is unavoidable, be sure to wear pro-

tective laser goggles that meet specifications.

• Make sure that no one enters the room when the machine is in this condition.

• When handling the laser unit, observe the “Precautions for Handling Laser

Equipment.”

DANGER

Invisible laser radiation when open.

AVOID DIRECT EXPOSURE

TO BEAM 0947-7127-01

1144D270AA

• To reassemble the product, reverse the order of disassembly unless otherwise specified.

• While the product is energized, do not unplug or plug connectors into the circuit boards

or harnesses.

• The magnet roller generates a strong magnetic field. Do not bring it near a watch, floppy

disk, magnetic card, or CRT tube.

• An air gun and vacuum cleaner generates a strong electrostatic charge that can destroy

the ATDC sensor and other sensors. Before cleaning a component with one of these

devices, be sure to remove all the sensors. Otherwise, use a blower brush and cloth

when cleaning parts.

• When handling circuit boards with MOS ICs, observe the “INSTRUCTIONS FOR HAN-

DLING THE PWBs WITH MOS ICs” (applicable only to the products using MOS ICs).

• The PC Drum is a very delicate component. Observe the precautions given in “HAN-

DLING OF THE PC DRUM” because mishandling may result in serious image problems.

• Note that replacement of a circuit board may call for readjustments or resetting of partic-

ular items, or software installation.

• After completing a service job, perform a safety check. Make sure that all parts, wiring

and screws are returned to their original positions.

• Check the area surrounding the service site for any signs of damage, wear or need of

repair.

• Do not pull out the toner hopper while the toner bottle is turning. This could result in a

damaged hopper motor or locking mechanism.

• If the product is to be run with the front door open, make sure that the toner hopper is in

the locked position.

Other Precautions

SAFETY INFORMATION

This printer is a page printer which operates by means of a laser. There is no

possibility of danger from the laser, provided the printer is operated according to

the instructions in this manual.

Since radiation emitted by the laser is completely confined within protective

housing, the laser beam cannot escape from the machine during any phase of

user operation.

Laser Safety

This printer is certified as a Class 1 Laser product under the U.S.

Department of Health and Human Services (DHHS) Radiation

Performance Standard according to the Radiation Control for Health

and Safety Act of 1968. This means that the printer does not produce

hazardous laser radiation.

CDRH Regulations

The Center for Devices and Radiological Health (CDRH) of the U.S.

Food and Drug Administration implemented regulations for laser

products on August 2, 1976. Compliance is mandatory for products

marketed in the United States. The label shown below indicates

compliance with the CDRH regulations and must be attached to laser

products marketed in the United States.

Internal Laser Radiation

Maximum Radiation Power: 0.6 (mW) at laser aperture of the print

head unit

Wave Length: 770-810 (nm)

This product employs Class IIIb Laser Diode.

Laser Diode and Scanning Polygon Mirror are incorporated in the

print headunit. Theprint head unit is NOT A FIELD SERVICE ITEM.

Therefore, the print head unit should not be opened under any

circumstances.

WARNING: Use of controls, adjustments or performance of procedures

other than those specified in this manual may result in hazardous radiation

exposure.

This is a semiconductor laser. The maximum power of the laser diode is 5

mW and the wavelength is 770-810 nm.

vii

For Denmark Users;

For Finland, Sweden Users;

For Norway Users;

ADVARSEL

Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion.

Undgå udsættelse for stråling.

Klasse 1 laser produkt der opfylder IEC825 sikkerheds kravene.

VARNING!

Osynlig laserstråining när denna del är öppnad och spärren är urkopplad.

Betrakta ej stråien.

VARO!

Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle

lasersäteilylle. Äjä katso sätee

VARNNING

Om apparaten används påannat sätt än i denna bruksanvisning specificerats,

kan användaren utsättas för osynlig laserstrålning som överskrider gränsen

för laser klass 1.

VAROITUS

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla

saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteiylle.

ADVARSEL

Dersom apparatet brukes på annen måte enn spesifisert i denne

bruksanvisning, kan brukeren utsettes for unsynlig laserstråling som

overskrider grensen for laser klasse 1.

Dette er en halvleder laser. Maksimal effeckt til laserdiode er 5mW og

bølgelengde er 770-810 nm.

viii

WARNING LABEL

laser

4121s001

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Minolta Drucker Handbücher

Minolta

Minolta EP1054 Bedienungsanleitung

Minolta

Minolta PagePro 1250W Bedienungsanleitung

Minolta

Minolta magicolor 2300 Series Bedienungsanleitung

Minolta

Minolta FIERY Pi5500 Bedienungsanleitung

Minolta

Minolta PAGEWORKS 20 Bedienungsanleitung

Minolta

Minolta Di552 Bedienungsanleitung

Minolta

Minolta CF2002 Bedienungsanleitung

Minolta

Minolta Di151 Bedienungsanleitung

Minolta

Minolta MAGICOLOR 2 PLUS Bedienungsanleitung

Minolta

Minolta PAGEWORKS 8E Bedienungsanleitung

Minolta

Minolta Di251 Bedienungsanleitung

Minolta

Minolta magicolor 330 Bedienungsanleitung

Minolta

Minolta PageWorks Pro 18N Bedienungsanleitung

Minolta

Minolta PageWorks Pro 18N Bedienungsanleitung

Minolta

Minolta PageWorks Pro 18L Bedienungsanleitung

Minolta

Minolta Magicolor 3100 Series Bedienungsanleitung

Minolta

Minolta PAGEPRO EX Bedienungsanleitung

Minolta

Minolta MAGICOLOR 2350 Bedienungsanleitung

Minolta

Minolta Magicolor 2300 DL Bedienungsanleitung

Minolta

Minolta Magicolor 2300 DL Bedienungsanleitung

Minolta

Minolta CF2001P Bedienungsanleitung

Minolta

Minolta PageWorks Pro 20 Bedienungsanleitung

Minolta

Minolta Di151 Bedienungsanleitung

Minolta

Minolta magicolor 7300 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung