Miro TD271 Bedienungsanleitung

miro TD271 Manual

miro

Displays GmbH

TRIFORUM

Haus A1

Frankfurter Str. 233

D-63263 Neu-Isenburg

Tel.0180-5 22 35 26 (0.12Euro/Min)

Fax 06102-3667-77

e-mail:[email protected]

TABLE OF CONTENTS

INTRODUCTION

FCC Compliance Statement..............................................................i

Safety Instructions ..........................................................................iii

General Information..........................................................................1

Equipment Checklist ........................................................................2

Monitor Features ..............................................................................3

GETTING STARTED

Installation ........................................................................................4

Control Buttons ................................................................................5

On-Screen Display ..........................................................................6

ON-SCREEN CONTROLS

Menu Descriptions............................................................................7

REFERENCE

Power Management ......................................................................10

Timing Guide ..................................................................................12

Pin Assignment ..............................................................................13

Specifications..................................................................................14

Troubleshooting..............................................................................15

FCC COMPLIANCE STATEMENT

Note:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of FCC Rules. These limits

are designed to provide reasonable protection against radio frequency

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy. If not installed and used in

accordance with the instructions, it may cause interference to radio com-

munications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause interferen-

ce to radio or television reception (this can be determined by turning this

equipment off and on), the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To comply within the limits for an FCC Class B computing device, always

use the shielded signal cord supplied with this unit.

CAUTION TO THE USER:

The Federal Communications Commission warns that changes or modifi-

cations to the unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. If

necessary, the user should contact the dealer or an experienced

radio/television technician for additional suggestions. The user may find

the Federal Communications Commission booklet, How to Identify and

Resolve Radio-TV Interference Problems, helpful. This booklet is

available from the U.S. Government Printing Office, Washington, D.C.,

Stock No. 004-000-00345-4.

NOTICE OF COMPLIANCE WITH CANADIAN

INTERFERENCE-CAUSING EQUIPMENT

REGULATIONS

SAFETY INSTRUCTIONS

HANDLING

Read all of these instructions. Save these instructions for later use.

Due to its fragile glass panel, this monitor must be handled with caution

and not exposed to impact or shock. Never touch the display area or

rub it with a hard stiff object or tool, as the panel is easily scratched.

CLEANING

Unplug this monitor from the wall outlet before cleaning.

The display area is highly prone to scratching. Do not use ketone-type

cleaners (i.e. acetone), ethyl alcohol, toluene, ethyl acid or methyl

chloride to clean the panel. Doing so may result in permanent damage.

Water, IPA (Iso Prophyl Alcohol) and Hexane are safe cleaners.

Do not allow oil or water to penetrate the display, as droplets cause

staining and discoloration with time.

Keep food particles and fingerprints away from the display area at all

times.

STORAGE

Store the monitor in a dark place away from sunlight and ultraviolet

(UV) radiation, as air bubbles may develop within the glass panel with

time.

Do not store the display in temperatures higher than 40°C/104°F or

humidity greater than 90%. Avoid condensation.

FCC COMPLIANCE STATEMENT

DDC COMPLIANCE NOTICE:

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

ii iii

GENERAL INFORMATION

This monitor is a high-performance intelligent multi-scan TFT LCD color

monitor for IBM compatible PC and Apple Macintosh. It is designed to be

compatible with all display modes for 17” inch LCD monitor.

Your new LCD monitor has many advantages : safe from electromagnetic

wave, lights, sharps and slims. This makes the monitor extremely suitable

in the environment of administration, transportation system research, etc.

Your new LCD monitor does not emit any X-ray radiation and the

magnetic emission greatly reduces the eyestrain.

Your new LCD monitor is designed for only Analog input support.

User friendly interface -- the easy and precise OSD control of 4 keys

button. You can use these controls to adjust the display as you desire.

Brief appearance -- multimedia featured in an elegant and compact

housing.

Your new LCD monitor incorporates an active TFT module. It has a

1280 x 1024 pixel resolution, high contrast, high luminance and fast

response time.

SAFETY INSTRUCTIONS

CAUTION

1. Do not open any covers on the monitor. No user serviceable

parts are inside.

2. In an emergency, disconnect the AC power plug.

3. To avoid electrical shock, disconnect the power cord from the AC

adapter before connecting the signal cable to the computer.

4. Keep away from liquids and flame. Do not immerse this monitor

in water or any other liquid. Do not use this device in excessively hot

conditions.

5. Handle the power cord with care. Do not bend the power cord

excessively or place heavy objects on it. Do not use a damaged

power cord, as doing so can result in fire or electrical shock hazards.

When disconnecting the power cord, always grasp the plug, not the

cord.

6. The liquid crystals in the display panel contain several irritants. If the

panel is damaged or broken, do not allow the liquid to come in

contact with skin, eyes, or mouth. If you come in contact with the

liquid, flush the affected area with running water for at least

15 minutes, then consult a doctor.

7. Handle this monitor with care when moving it. When lifting the

monitor, support it with one hand holding the stand, and one

hand holding the LCD screen.

8. Always disconnect the power cord when moving this monitor.

9. Do not lay this monitor in a horizontal position when operating.

iv 1

MONITOR FEATURES

* Supports Analog IBM compatible PC, Apple MacintochTM

*VESA Display Data Channel (DDC) 1/2B compatible

*Micropocessor based with OSD (On Screen Display) control.

*On Screen Control : Auto Adjustment, Contrast, Brightness,

H/V Position, H-Size, Phase, Color Control, OSD Position, Language,

Reset.

*Built-in color active matrix TFT (Thin Film Transistor) Liquid Crystal

Display (LCD) that uses amorphous silicon TFTs as a switching device.

*Multi-scanning at horizontal frequencies of 31kHz to 80kHz and vertical

frequencies of 60Hz to 75Hz.

*Compatible with standard IBM VGA, extended VGA, super VGA,

IBM XGA modes, super XGA, as well as VESA resolution standards

*Resolution : up to 1280 x 1024

*Dot pitch : 0.264mm(H) x 0.264mm(W)

*Universal power supply : AC 90 - 264V allowed

*Power consumption Normal : < 40 Watt

Power Saving : < 3 Watt

Off : < 3 Watt

*Outside dimension : 459mm(W) x 467mm(H) x 165mm(D)

*Weight (net) : 7.5kg

EQUIPMENT CHECKLIST

Before operating your display, please check to make sure that all of the

items listed are present in your package:

• Color TFT LCD Monitor

• Accessory Box:

1. AC to DC Adapter & Power Cord

2. Signal Cable 15-pin D-Sub

3. Audio cable

4. This manual

Note : If any item(s) are missing or damaged, contact your dealer

immediately.

Remove the monitor from its shipping carton.

Save the carton and packaging materials in case you need to relocate the monitor.

2 3

INSTALLATION

Assembly instruction

1. Mount the LCD panel by sliding the back side of the LCD panel into the

monitor bracket. Make sure the LCD panel is secured into the locked position.

Follow these steps to install the monitor

1. Before you connect the cables, make sure the monitor and system

unit power switches are OFF.

2. Plug one end of the 15-pin signal cable to the rear of your system

and the other end to monitor’s signal input. The adapter may be

required for certain Apple Macintosh computers. Tighten the two

screws on the cable connector.

3. Connect the audio cable between the monitor’s audio input and the

PC’s audio output.

4. Attach the female end of the power cord to the adapter, then plug the

adapter connector to the power “DC-IN” jack of the LCD monitor.

Plug the male end of power cord into an AC wall outlet.

5. Turn on your computer and your LCD monitor.

4 5

CONTROL BUTTONS

Front Controls

BUTTON DESCRIPTION:

1. : Menu button

To push menu button turns on the menu, and it activates the

items you highlight.

2. : Select button

To choose which function you need in OSD Menu and to

increase and to decrease the volume, you may click or

3. : Auto button

Press "A" button 2 seconds the auto adjust display mode will

tune to the utmost performance according to VGA setting.

In the event of the display image needs further adjustment.

To ensure best Auto-Adjustment perfomance

a. Attempt to Start/Close Windows page (No need to Shut Off)

b. Press “A” button for 2 seconds

The monitor display will be then best adjusted.

REMARK: The highest display frequency generates at Close-

Windows stage (on-off graphics pattern). Per rec. processes

facilitate to best Auto-Adjustment under default environment.

4. : Power button

Use this button to turn the monitor on and off

5. : Power indicator

This light glows green during normal operation and glows

orange during power off. Glows orange and flash during

power saving mode.

Select Button (2)

Menu Button (1)

Auto Button (3)

Power Indicator (5)

Power Button (4)

MENU DESCRIPTIONS

Main Menu

CONTRAST

This control allows you to make adjustments to the contrast of the

display screen.

BRIGHTNESS

Selecting this control allows you to make adjustments to the luminosity

level of the display screen.

H-POSITION (HORIZONTAL POSITION)

Select this control and then use the and select buttons (2) to

center the image horizontally on the screen.

V-POSITION (VERTICAL POSITION)

Select this control and then use the and select buttons (2)

to center the image vertically on the screen.

H-SIZE (HORIZONTAL SIZE)

Select this control and then use the and select buttons (2) to

expend or decrease the image width to horizontally fill the display screen.

ON-SCREEN DISPLAY

This LCD monitor features an On-Screen Display (OSD) menu. These

icons are designed to make your monitor display settings easier. When

highlighted, the icons illustrate the control function to assist you in

identifying which control needs adjustment.

Before activating the OSD menu, the Auto button (3) can be used to

automatically adjust the display to the proper size and horizontal and

vertical position. (Press button for 2 seconds.)

The OSD menu activates automatically when you press the

Menu button (1) on the front of the monitor. The OSD remains centered

on the screen while you make your adjustments. Use either the

or select button (2) to move the highlight to your selection. Pressing

menu button (1) the submenu will appear nearby main menu. Press Menu

button (1) and release again, the highlight of adjusted items and scroll bar

will change the color from black to blue. Use the or select

button (2) to adjust the control.

When you have finished making adjustments, press the menu button (1)

to save settings. The scroll bar will change to black. You can select other

function to make adjustment. Also you can select EXIT icon and press

menu button (1) to go back to main menu.

6 7

MENU DESCRIPTIONS

LANGUAGE

Select this control and then use the and select buttons (2) to

choose on of the seven language you need.

RESET

Reset the currently highlighted control to the factory setting. User must

be using factory preset video mode to use this function.

* Note:

You can get the best quality of the image under full-screen image with a running

computer. The function of AUTO-TUNE may not work properly if background color

is dark or if the input image does not fill the screen. (ex: DOS text mode)

We strongly recommend that you just run the AUTO-LEVEL & AUTO-TUNE function

to get the best image quality when you unpack the monitor or when you install dif-

ferent VGA card or PC.

MENU DESCRIPTIONS

AUTO

Auto adjust display mode to its utmost performance according to VGA

setting. In the event of the display image needs further adjustment.

COLOR CONTROL

Select this control, then use the and select buttons (2) to scroll to

the desired color temperature.

COOL

This control adjusts the color temperature of the screen image this

item are preset by factory, you can not adjust these setting. The

perfomance is bluer and brighter.

WARM

The performance is redder and closer to paper white.

PHASE

Select this control and then use the and select buttons (2) to adjust

the screen image until it looks focused, crisp and sharp.

OSD ADJUSTMENT

YoucanchoosewhereyouwouldlikeOSDimagetoappearon your screen.

H-POSITION (HORIZONTAL OSD-POSITION)

Select this control and then use the and select buttons (2) to

center the OSD-Screen horizontally on the screen.

V-POSITION (VERTICAL OSD-POSITION)

Select this control and then use the and select buttons (2)

to center the OSD-Screen vertically on the screen.

EXIT

To exit the sub menu.

8 9

TIMING GUIDE

The LCD is a multi-frequency display. It operates at horizontal frequencies

between 31KHz - 80KHz and vertical frequencies between 60Hz - 75Hz.

Because of its microprocessor-based design, it offers auto-

synchronization and auto-sizing capabilities. This monitor offers 11 pre-

programmed settings that are listed in the timing table on page 12.

These preset modes cover most of the common video modes supported

by popular graphics adapters. However, each adapter’s implementation of

these video modes may vary slightly. If you find it necessary to make

minor display adjustments (for example, horizontal and vertical position).

Please refer to the On Screen Display section of this manual for

instructions.

If you would like to use one of the preset timing modes, please refer to

your video card manufacturer’s installation guide for instructions on how

to make these changes. The video card controls the refresh rate. Most

video cards provide a software utility or hardware DIP switches that allows

you to change the frequency used for each resolution.

POWER MANAGEMENT

LED INDICATOR (POWER MANAGEMENT ACITVE)

The power management feature of this LCD monitor is comprised of two

stages: On or Out Of Range (Green), OFF (Amber/Green blinking).

In the off mode, all circuitry in the monitor is shut down, except for a low

power detection circuit. This circuit allows the monitor to wake up when

the mouse is moved or a key on the keyboard is pressed.

Power Mode H-Sync V-Sync Video LED Color

Normal Pulse Pulse Active Green

Out Of Range Pulse Pulse Active Green

Off Pulse No pulse Blanked Amber blinked per 1 sec.

Off No pulse Pulse Blanked Amber blinked per 1 sec.

Off No pulse No pulse Blanked Amber blinked per 1 sec.

10 11

Inhaltsverzeichnis

Sprachen:

Andere Miro Monitor Handbücher

Miro

Miro TD490 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung