MistAway iMistAway Bedienungsanleitung
iMistAway Setup Guide
Verify iMistAway Kit Contents
Step Two –Mount iMistAway Node on Misting Unit
A7:D3
iMistAway
Gateway
iMistAway Node Antenna (Gen 1.3) Ethernet Cable
and Power
Adapter
Step One –Install Gateway Unit
Gen 3 Antenna Kit.
Con tains 1 antenna, 1 antenna cable
and 2 mo unting nuts (not pictured)
Gen 1.3 Mounting Location
Gen 3 Mounting Location
Gen 1.3 (Tank Unit)
Connect the Gateway Unit to your customer’s Internet router or modem
using the included CAT-5 cable.
Connect your iMistAway Gateway Unit to the power adapter.
Place the gateway in a position which is as elevated as possible and not in
a metal cabinet –this will help to maximize wireless signal strength.
When the Gateway Unit is connected to the iMistAway server, the
“globe” symbol ( ) will be lit up with a solid green light.
Record the MAC Address and PAN ID on the Gateway Unit label.
Thread antenna onto iMistAway Node.
Mount node inside unit, next to the remote receiver. The Node antenna
should point away from the remote reciever. The Node ships with red
mounting tape attached.
Mount iMistAway Node to underside of lid. Use the two nuts supplied in
the Antenna Kit to secure the iMistAway Node to the lid.
Connect supplied antenna cable to male connector on iMistAway Node
Push the male connector end of the supplied antenna cable through hole
in lid of misting unit. Secure cable using attached nut, washer and o-ring.
IMPORTANT - O-Ring on antenna cable must be placed on the top of the lid before
securing the cable using the attached nut.
Thread iMistAway antenna onto the antenna connector.
A
B
C
D
E
A
B
A
B
C
Gen 3 (Tankless Unit)
D
Step Three –Plug iMistAway Node into Controller and Set PAN ID
IMPORTANT! The misting unit must be POWERED OFF when connecting the Node to the controller.
PAN 27NET ON
Day/Time
Cycles
Custom PGM
Set-Up
Maintenance
Data
MENU
STOP
PAN 27
Day/Time
Cycles
Custom PGM
Set-Up
Maintenance
Data
MENU
STOP
If the connector is plugged in the wrong way, your
MistAway unit will not power on!
C D
B
Unplug or power down misting unit
Plug the six pin connector from the node into the controller
data port as shown. The cable should point down toward
the colored labels.
Restore power to misting unit. Confirm “Net On” appears
during controller boot cycle.
Navigate to the DATA menu and press the up arrow until
PAN ID appears on the display. Press and hold the green
arrow key to set the PAN ID.
Select the PAN ID and press the green arrow key. When the PAN ID is set, the controller will display “DONE”.
A
B
C
D
E
iMistAway Activation
866-485-7255 or 713-468-6464
Extension 324
Log into iMistAway.com (or use the mobile app) to confirm wireless operation.
Step Four –Contact MistAway for Activation
To activate the iMistAway, contact MistAway Technical
Support.
When calling support, please be sure to have the MAC
Address for your iMistAway unit.
You will need to provide this information when calling in.
The MAC Address is listed on the Gateway Unit as well as
the iMistAway box.
Inhaltsverzeichnis
Andere MistAway Insektenbekämpfungsgeräte Handbücher
MistAway
MistAway iMistAway/Gen 3 Bedienungsanleitung
MistAway
MistAway GEN III Bedienungsanleitung
MistAway
MistAway GEN III Handbuch
MistAway
MistAway Gen 1.3 Bedienungsanleitung
MistAway
MistAway Gen 1.2 Bedienungsanleitung
MistAway
MistAway Gen II Bedienungsanleitung
MistAway
MistAway Mosquito Bedienungsanleitung
Beliebte Insektenbekämpfungsgeräte Handbücher anderer Marken
Olimpia electronics
Olimpia electronics RT-52/HACCP Bedienungsanleitung
One Stop Gardens
One Stop Gardens SOLAR INSECT KILLER 95500 Kurzanleitung
Dynamic
Dynamic Dynatrap XL Bedienungsanleitung
Stinger
Stinger BKC40 Series Gebrauchs- und Pflegehandbuch
Agrimate
Agrimate AF-4000NK-VM Bedienungsanleitung
INSECT-O-CUTOR
INSECT-O-CUTOR Luralite Cento Bedienungsanleitung