Mitel Rack PDM Charger Bedienungsanleitung

Rack PDM Charger

INSTALLATION AND OPERATION MANUAL

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

NOTICE

The information contained in this document is believed to be accurate in all respects but is not

warranted by Mitel Networks™ Corporation (MITEL®). Mitel makes no warranty of any kind

with regards to this material, including, but not limited to, the implied warranties of merchant-

ability and fitness for a particular purpose. The information is subject to change without notice

and should not be construed in any way as a commitment by Mitel or any of its affiliates or

subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors or

omissions in this document. Revisions of this document or new editions of it may be issued to

incorporate such changes.

No part of this document can be reproduced or transmitted in any form or by any means - elec-

tronic or mechanical - for any purpose without written permission from Mitel Networks Corpo-

ration.

TRADEMARKS

The trademarks, service marks, logos and graphics (collectively "Trademarks") appearing on

Mitel's Internet sites or in its publications are registered and unregistered trademarks of Mitel

Networks Corporation (MNC) or its subsidiaries (collectively "Mitel") or others. Use of the

Trademarks is prohibited without the express consent from Mitel. Please contact our legal

department at [email protected] for additional information. For a list of the worldwide Mitel

Networks Corporation registered trademarks, please refer to the website: http://

www.mitel.com/trademarks.

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

1. INTRODUCTION

This document describes how to install, configure and operate the Rack PDM Charger.

This Rack Charger is aimed DT390, DT69x, DT4x3, Mitel 5613 and 5614 for MiVoice

MX-ONE and Mitel 5603, 5604, 5607, 5624 for MiVoicce Business and MiVoice 250.

NOTE: The Rack PDM Charger is designed to be connected to an Ethernet based local

area network.

Each Rack PDM Charger can charge up to six handsets simultaneously.

The USB port on the Rack PDM Charger is used to connect the Rack PDM Charger to

a CPDM3/WSM3, or to a PC running the Portable Device Manager (WinPDM/PDM).

The CPDM3/WSM3 or WinPDM can be used to configure or upgrade either the Rack

PDM Charger itself or any handsets placed in the Rack PDM Charger.

The Ethernet ports can be used to connect up to four Rack PDM Charger to a single

LAN outlet.

See 2.1.5 Communication Cable Connection on page 14 for more information on how to

connect Rack PDM Chargers using the Ethernet and USB ports.

Figure 1. Rack PDM Charger.

This document is intended as a guide for installation, maintenance and

troubleshooting.

Model Features

Rack PDM Charger - Charging slots for handsets.

- Ethernet and USB connection used for

upgrade and configuration of handsets

and Rack PDM Chargers (through a LAN

or PC connection).

Note: For the Mitel 5624 (WiFi) wireless

handset, this Rack PDM Charger only

provides charging.

Power Supply for Rack PDM

Charger Building fuse for fixed

installation

Supply voltage 100-240VAC/0.7A 50/60 Hz 10 A maximum

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

Installation Alternatives

NOTE: In the USA and Canada the Rack PDM Charger can only be installed as a

single unit, serial configuration is not permitted.

• The Rack PDM Charger can be installed as a single unit. When installed as a single

unit, the power cord with the C14 connector can be used together with a suitable

extension cord, and can be plugged into a wall outlet. Up to four Rack PDM Charger

single units can be connected to one LAN outlet.

• If more than one Rack PDM Charger is used in a serial configuration a fixed

installation must be made. For safety reasons it is NOT allowed to supply more than

one unit by the power cord with the C14 connector. When units are supplied in

series, the installation must be made by an authorized electrician and the C14

connectors must be removed. A maximum of five units can be connected in serial

power supply, but LAN serial connection is limited to four units.

NOTE: In Sweden, Norway and Finland a connection to protective earth (safety

grounding) must be provided.

1.1 ABBREVIATIONS AND GLOSSARY

BPC Battery Pack Charger

device Can be a DECT or VoWiFi handset, an alarm transmitter,

a pager or a charger developed to work together with the

PDM/Device Manager. See respective manual for each

device.

DHCP Dynamic Host Configuration Protocol, a protocol for

automating the configuration of computers that use TCP/

WinPDM/PDM Portable Device Manager

A Stand Alone (SA) application for administration through

a cable connected PC.

USB Universal Serial Bus: a serial bus standard to interface

devices, for example connect computer peripherals such

mice, keyboards, scanners etc.

1.2 SAFETY

The Rack PDM Charger is connected to 100-240VAC/0.7A 50/60 Hz.

For safety reasons:

• the safety covers on top of the supply voltage terminal blocks must be mounted to

prevent hazardous situations, such as an electric shock.

• when servicing the units the mains power supply cable must be disconnected.

NOTE: For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible

disconnect device shall be incorporated into the building installation wiring. The

disconnect device shall disconnect both poles.

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

NOTE: For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

In Sweden, Norway and Finland the Rack PDM Charger must be connected to a wall

outlet with protective earth (safety grounding). For other countries it is recommended to

use a protective earth connection.

• Suomi: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

• Norge: Apparatet må tillkoples jordet stikkontakt.

• Sverige: Apparaten skall anslutas till jordat uttag.

1.3 REGULATORY COMPLIANCE STATEMENTS (EU AND

EFTA ONLY)

The CE marking affixed to Mitel products indicates conformance to the R&TTE

directive 99/05/EC (Radio and Telecommunications Terminal Equipment Directive. As

of June 13the 2017R&TTE directive 1999/5/EC is replaced, in this document, by EMC

2014/30/EU). For a copy of the original signed Declaration (in full conformance with

EN45014), please contact your Mitel office or Sales partner.

1.4 REGULATORY COMPLIANCE STATEMENTS (USA AND

CANADA ONLY)

FCC Compliance Statements for USA

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IC Requirements for Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B conforme á la norme NMB-003 du Canada.

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

Modifications

Changes or modifications to the equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

1.5 TECHNICAL SOLUTION

The following functionality is provided by the Rack PDM Charger:

When using an Ethernet connection, it is possible to connect several Rack PDM

Chargers serially to the LAN.

If the Rack PDM Charger is connected to a PDM via both USB and Ethernet, the USB

connection has higher priority.

NOTE: If the Ethernet connection is used, each Rack PDM Charger needs an IP

address.

See label for MAC address.

The Rack PDM Charger is equipped with a combined reset button and embedded LED

on the front.

1.6 INTERFACES

NOTE: The requirements stated below are only applicable for the Rack PDM Charger.

Computer:

• Microsoft Windows XP®Professional, Service Pack 2 (SP2) (32-bit), or Windows

7® Professional (32-bit/64-bit), Windows 7® Enterprise (32-bit/ 64-bit), Windows 7®

Ultimate (32-bit/64-bit)

• Sun Java Runtime Environment (JRE) version 6 or higher.

• USB port. USB 1.1 required, USB 2.0 supported.

• Ethernet port 10/100 Mbit/s.

Charger functionality

- Charging of the handset battery.

- Provide a means for software and parameter update of handsets.

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

2. INSTALLATION AND CONFIGURATION

2.1 RACK PDM CHARGER INSTALLATION

2.1.1 GENERAL

NOTE: The unit shall be installed by authorized personnel only.

• The units shall be placed in a dry environment with a temperature range from

+5° C up to + 40° C (41° F to 104° F).

• The units shall be mounted on a vertical wall.

• Avoid mounting the Rack PDM Charger in a sunlit place. This can affect the

charging capacity.

• Avoid mounting the Rack PDM Charger where radio/network coverage is not

sufficient. This can reduce the messaging capacity.

• The unit can be mounted to a vertical wall (concrete or plaster walls only) or be

placed on table if table adapters are used.

• If the Rack PDM Charger is connected to a power supply via an AC wall plug, serial

power supply connection is not allowed.

• If the Rack PDM Charger is connected to a power supply via an AC wall plug, the

socket-outlet shall be situated near the equipment and shall be easily accessible.

• If the Rack PDM Charger is connected to a power supply via a fixed connection, a

readily accessible disconnect device shall be incorporated in the building installation

wiring.

Delivery Includes:

• Rack PDM Charger

• Power supply cord including IEC C14 connector (male)

• Inlet accessory kit including cable support holders and screws

• Table adapters

NOTE: An extension cord IEC C13 AC connector (female, IEC60320-C13) to wall

socket has to be ordered separately. It shall be connected between the pre-

installed IEC C14 AC connector (male) and the wall socket.

Required Tools etc.

• Screwdrivers

• Cutting pliers

•Multimeter

• Screws and wall plugs for wall mounting. Make sure the screws and wall plugs have

the correct length for the type of wall used. See example below:

Wall material Plug length Screw diameter

Single plasterboard Thorsman TP1 3.5 – 5 mm

Double plasterboard Thorsman TP2 3.5 – 5 mm

Concrete Thorsman TP2 3.5 – 5 mm

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

Examples of Ways to Mount the Rack PDM Chargers

Different ways to mount the Rack PDM Charger is shown in figure 6 on page 11. It is

possible to set up different combinations of Rack PDM Chargers and Battery Pack

Chargers. A maximum of four Rack PDM Chargers (or Battery Pack Chargers) can be

serially connected to the same LAN source.

Installation Steps for the Rack PDM Charger

The installation is done in three steps:

1 Placing on table or wall mounting.

2 Electrical installation.

3 Communication cable connection.

Installation Steps for the Rack PDM Charger

The installation is done in two steps:

1 Placing on table or wall mounting.

2 Electrical installation.

2.1.2 PLACING ON A TABLE

If the Rack PDM Charger shall be placed on table, use the table adapters included in

the delivery as follows:

1 Mount the two table adapters in the two outer holes in the bottom cover of the

Rack PDM Charger as shown in figure 2 on page 8.

2 Mount the four rubber feet as shown in figure 2 on page 8.

Figure 2. Mounting of table adapters and rubber feet.

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

Figure 3. Rack PDM Charger with table adapters.

2.1.3 WALL MOUNTING

First, make an outline of how the Rack PDM Chargers are to be placed.

TIP: If several Rack PDM Chargers (or Battery Pack Chargers) are to be mounted

close to each other, mount them so that there is enough space between them to be

able to disconnect the handsets (vertical distance) and to be able to open the top cover

(horizontal distance).

TIP: When you are planning the location of the modules, start to mount them in a height

that makes it easy to reach the handsets and to read the handsets’ display.

Measure and mark the drill holes by using the dimensions in figure 4. Drill and fasten

the Rack PDM Charger on the wall with four screws.

Figure 4. Mounting dimensions in mm. Rack PDM Charger seen from the back.

2.1.4 ELECTRICAL INSTALLATION

Power Supply by Power Cord to Wall Outlet

The Rack PDM Charger is delivered with a cord with an IEC C14 connector (male). An

extension cord IEC C13 AC connector (female, IEC60320-C13) to wall socket has to

be ordered separately. It shall be connected between the pre-installed AC connector

(male) and the wall socket.

Figure 5. Rack PDM Charger with IEC C14 connector and an extension cord with an

21/1531-ANF 901 43 F 2017-04-25

Rack PDM Charger

Installation and Operation Manual

IEC C13 connector.

For the Rack PDM Charger, connect the communication cable when required.

Installation Test

1 Connect the mains power supply cord to the wall socket.

2 The LED on the front of the charger should light up.

NOTE: The LED is disabled on the Rack PDM Charger and will not light up. Put a

handset into a charging slot and check if the handset LED lights up.

Power Supply by Fixed Connection

NOTE: If the Rack PDM Charger shall be connected with a fixed connection, the AC

connection must be done by a authorized electrician.

TIP: It is possible to use any of the two AC terminal blocks for AC input. Consequently,

the unused terminal block may be used to connect the next Rack PDM Charger or

battery pack charger.

The Power Supply module connects to 100-240VAC/0.7A 50/60 Hz. When working

with the units the mains power supply cable must always be disconnected. The safety

covers must be mounted on top of the power supply terminal blocks to prevent

hazardous situations, like electric chock.

Inhaltsverzeichnis

Andere Mitel Akkuladegerät Handbücher

Mitel

Mitel Desk PDM Charger Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung