Mitel MX-ONE Bedienungsanleitung

INSTALLATION INSTRUCTION

Installing Boards and Cabling

Göran Lanner grenglannerg renGöran Lanner grenglannerg renGlobenMitel Swed en ABR&D MX-ONE & InAttend

21/1531-ASP11301 Uen C 2017-03-28 2

NOTICE

The information contained in this document is believed to be accurate in all respects

but is not warranted by Mitel Networks™ Corporation (MITEL®). Mitel makes no

warranty of any kind with regards to this material, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. The informa-

tion is subject to change without notice and should not be construed in any way as a

commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and

subsidiaries assume no responsibility for any errors or omissions in this document.

Revisions of this document or new editions of it may be issued to incorporate such

changes.

No part of this document can be reproduced or transmitted in any form or by any means

- electronic or mechanical - for any purpose without written permission from Mitel

Networks Corporation.

TRADEMARKS

The trademarks, service marks, logos and graphics (collectively "Trademarks")

appearing on Mitel's Internet sites or in its publications are registered and unregistered

trademarks of Mitel Networks Corporation (MNC) or its subsidiaries (collectively

"Mitel") or others. Use of the Trademarks is prohibited without the express consent from

Mitel. Please contact our legal department at [email protected] for additional informa-

tion. For a list of the worldwide Mitel Networks Corporation registered trademarks,

please refer to the website: http://www.mitel.com/trademarks.

INSTALLING BOARDS AND CABLING

321/1531-ASP11301 Uen C 2017-03-28

1 INTRODUCTION

MX-ONE is a communication solution for enterprises. MX-ONE integrates voice

communication in fixed and mobile networks for public as well as private service.

MX-ONE can be integrated into an existing Local Area Network (LAN) infrastructure.

MX-ONE supports both IP telephony and functions found in classic circuit-switched

PBXes (Private Branch Exchanges).

1.1 SCOPE

This document describes the MX-ONE cabling and connection in a detailed way. It is

aimed for customers doing new installation. For other parts of the Installation see:

•Installation preparation and Earthing, 19/1531-ASP11301

•Installation Chassis in a Cabinet, 20/1531-ASP11301

1.2 TARGET GROUP

The target group for this document is personnel involved in installing the MX-ONE.

1.3 PREREQUISITES

This section lists requirements that must be fulfilled before the installation starts.

1.3.1 ELECTRICAL CONNECTIONS

Installation procedures involving connection of power cables, batteries and earthing

must be performed according to local regulations.

1.3.2 SAFETY

All personnel involved in installation must read and understand the safety instructions

prior to installation, see the description document for SAFETY.

21/1531-ASP11301 Uen C 2017-03-28 4

INSTALLING BOARDS

2 INSTALLING BOARDS

Device boards can, in the 7U chassis only be placed in the board positions 01-29 and

45-73. Not in positions 33, 37 and 41.

Note: It is important to firmly insert the boards, to avoid bending any back plane

connectors, or it’s contact pins. Press evenly on both sides of the front. Do NOT

use the extractor (available in some boards) to press the board in.Only for the

final millimeter of sliding in the board, the extractor is allowed to be used.

To remove any board, use the extractor, or use the tool LTD11702 in an available

keyhole in the fronts.

Table 1 Boards in MX-ONE

Note: Secure all boards with the screws located in the extractor. Use screw driver with

Torx T8.

Board Product

number

Building

height

Time

Slots

used

Remarks

ALU2 ROF 137 5373/11 20mm 8 Alarm unit for external alarms

ASU Lite ROF 137 6307/31 40mm --- Mitel Server Unit, Lite. 8GB. For more

information see item below.

ASU-II ROF 137 6307/4 40mm --- Mitel Server Unit. 16GB. For more

information see item below.

DC/DC ROF 137 6303/1 40mm --- Power unit for 7U chassis

ELU26 ROF 137 5321/12 20mm 8 ISDN-S digital extensions

ELU31 ROF 137 5412/4* 20mm 32 DECT extensions

ELU33 ROF 137 5062/1 20mm 32 Digital extensions

ELU34 ROF 137 5064/x 20mm 32 Analog extensions with message waiting

FTU2 ROF 137 5415/11 20mm 8 Failure Transfer Unit

MFU ROF 137 5348/X 20mm 8 Multi frequency unit

MGU2 ROF 137 6304/4 20mm --- Media Gateway Unit. For more

information see item below.

TLU76 ROF 137 5338/x* 20mm 32 Digital trunk, ISDN, E1, DPNSS, CAS,

SS7

TLU77 ROF 137 5387/x* 20mm 23 ISDN, T1, DPNSS, CAS depending on

version

TLU79 ROF 137 5349/11* 20mm 8 ISDN-T 2B+D trunk line

TLU80 ROF 137 5406/11 20mm 8 4-wire analog trunk using E&M signaling.

This board can only be used in MX-ONE

Classic. Not in MX-ONE Lite or 1U

TLU83 ROF 137 6305/1 20mm 8/12 Analog trunk line (loop start, ground start.

CLI with FSK and DTMF)

TLU83 ROF 137 6305/2 20mm 8/12 Analog trunk line (loop start, ground start,

call metering. CLI with FSK and DTMF)

TMU ROF 137 5335/x 20mm 32 Tone and Multi part Unit. DTMF

INSTALLING BOARDS AND CABLING

521/1531-ASP11301 Uen C 2017-03-28

2.1 ASU-II AND ASU LITE

The ASU’s has a disk bay for 2 separate HDD (Hard disk drives) or SSD (Solid state

drives). They are located behind a cover in the front.

Note: SW RAID1 is supported on Mitel ASU and ASU-II.

Close to the LED near the LAN-ports, there is a hole for performing reset/ software

shout down.

The ASU’s has a battery for real time clock. This battery is located just behind the board

for the SATA drives connection.

Note: Due to the high weight of these boards, handle them with care, and hold the

board only in the front. Also, be careful when inserting it into the subrack. Do not

force it to avoid any bending of the board.

2.2 MGU2

The MGU2 board has a 20mm front and can be used in any chassis.

Close to the LED there is a hole for performing reset.

For more info see description, Media Gateway Unit, MGU, 1/1551-ANF90136.

2.3 EMPTY BOARD POSITIONS

If any empty positions are left in a chassis after mounting all boards, these empty slots

have to be filled with Dummy-fronts to fulfill the EMC demands. See 2.4 Dummy Front

on page 6.

21/1531-ASP11301 Uen C 2017-03-28 6

INSTALLING BOARDS

2.4 DUMMY FRONT

This section describes the dummy front in 19" cabinets.

Dummy fronts are installed at all empty positions in the 19" chassis. New boards can

be installed at these positions. Remove the dummy front at the position were the new

board is to be installed and insert the new board.

Note: All empty board positions must be covered with dummy fronts to fulfill the EMC

requirement and to be compliant with the BYB501 cooling requirements (air

flow).

Table 2 Dummy Front

Figure 1: 20mm Dummy Front

2.5 CONNECTORS AND LEDS ON BOARD FRONTS

This section describes the connectors and LEDs on the boards.

The indication of board status with dual color LED is:

• Steady RED: The board is in passive state

• Flashing RED: Error state

• Alternating RED/GREEN: The board is starting up or is blocked.

• Steady GREEN: The board is active.

• Flashing GREEN: The board is active and is signaling.

Note: DC/DC-, MGU-, TLU77- and ASU-boards deviate from above. See the figures

below regarding how they differ.

Function Product Number

Front 20 mm SXK 106 1020/35

INSTALLING BOARDS AND CABLING

721/1531-ASP11301 Uen C 2017-03-28

Figure 2: TLU77, TMU, TLU76, ELU33, and ELU34 Board Fronts

21/1531-ASP11301 Uen C 2017-03-28 8

INSTALLING BOARDS

Figure 3: ASU Front Connectors

The SATA disks are located behind a cover. Two disks are used for RAID1.

M0001172A

ASU-E

SATA 0

SATA 1 1

Connector no: 1

Connector no: 2

LED:

Green

Connector no: 3

15 pole

female D-sub

2 RJ 45 ports

4 USB Ports

INSTALLING BOARDS AND CABLING

921/1531-ASP11301 Uen C 2017-03-28

Figure 4: DC/DC Front Connectors and LEDs

DC/DC

FAN UNIT

ALARM IN

-48V

INPUT

21/1531-ASP11301 Uen C 2017-03-28 10

INSTALLING BOARDS

Figure 5: ALU2, ELU31, TLU79, TLU80 and TLU83 Fronts

Note: ELU26 and TLU79 has equal fronts, only different printing.

Andere Handbücher für MX-ONE

Inhaltsverzeichnis

Andere Mitel Konferenzsystem Handbücher

Mitel

Mitel MiVoice Office 400 Bedienungsanleitung

Mitel

Mitel SX-200 Bedienerhandbuch

Mitel

Mitel MiVoice MX-ONE Bedienungsanleitung

Mitel

Mitel MiVoice Office 400 Bedienungsanleitung

Mitel

Mitel MiVoice 5000 Bedienungsanleitung

Mitel

Mitel MiVOICE BUSINESS Bedienungsanleitung

Mitel

Mitel 5760 VC Bedienungsanleitung

Mitel

Mitel Navigator 3300 ICP Bedienungsanleitung

Mitel

Mitel 3300 Bedienungsanleitung

Mitel

Mitel MiVOICE BUSINESS Bedienungsanleitung

Mitel

Mitel UC360 Bedienungsanleitung

Mitel

Mitel MiVoice Business 3300 ICP Bedienungsanleitung

Mitel

Mitel 5750 Montageanleitung

Mitel

Mitel 6863 SIP Bedienungsanleitung

Mitel

Mitel 3300 Konfigurationshandbuch

Mitel

Mitel SmarT-1 EuroRoute Installationsanleitung

Mitel

Mitel MIVOICE OFFICE 250 Bedienungsanleitung

Mitel

Mitel ACD 2000 Bedienungsanleitung

Mitel

Mitel SX-200 Bedienungsanleitung

Mitel

Mitel MIVOICE OFFICE 250 Bedienungsanleitung

Mitel

Mitel 3300 Konfigurationshandbuch

Mitel

Mitel Navigator 3300 ICP Installationshandbuch

Mitel

Mitel SX-200 EL Bedienungsanleitung

Mitel

Mitel Inter-Tel 5000 Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung