Mitel MX-ONE Bedienungsanleitung

INSTALLATION INSTRUCTION

Installing Chassis in a Cabinet

Göran Lanner grenglannerg renMSETero Silvennoienentsilvenn oinenGlobenMSER&D MX-ONE & InAttend

20/1531-ASP11301 Uen B5 2017-03-23 2

NOTICE

The information contained in this document is believed to be accurate in all respects

but is not warranted by Mitel Networks™ Corporation (MITEL®). Mitel makes no

warranty of any kind with regards to this material, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. The informa-

tion is subject to change without notice and should not be construed in any way as a

commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and

subsidiaries assume no responsibility for any errors or omissions in this document.

Revisions of this document or new editions of it may be issued to incorporate such

changes.

No part of this document can be reproduced or transmitted in any form or by any means

- electronic or mechanical - for any purpose without written permission from Mitel

Networks Corporation.

TRADEMARKS

The trademarks, service marks, logos and graphics (collectively "Trademarks")

appearing on Mitel's Internet sites or in its publications are registered and unregistered

trademarks of Mitel Networks Corporation (MNC) or its subsidiaries (collectively

"Mitel") or others. Use of the Trademarks is prohibited without the express consent from

Mitel. Please contact our legal department at [email protected] for additional informa-

tion. For a list of the worldwide Mitel Networks Corporation registered trademarks,

please refer to the website: http://www.mitel.com/trademarks.

INSTALLING CHASSIS IN ACABINET

320/1531-ASP11301 Uen B5 2017-03-23

1 INTRODUCTION

MX-ONE is a communication solution for enterprises. MX-ONE integrates voice

communication in fixed and mobile networks for public as well as private service.

MX-ONE can be integrated into an existing Local Area Network (LAN) infrastructure.

MX-ONE supports both IP telephony and functions found in classic circuit-switched

PBXes (Private Branch Exchanges).

1.1 SCOPE

This document describes the MX-ONE Cabinet Installation in a detailed way. It is aimed

for customers doing new installation. For other parts of the Installation see:

• Installation preparation and Earthing, 19/1531-ASP11301

• Installation boards and Cabling, 21/1531-ASP11301

1.2 TARGET GROUP

The target group for this document is personnel involved in installing the MX-ONE.

1.3 PREREQUISITES

This section lists requirements that must be fulfilled before the installation starts.

1.3.1 ELECTRICAL CONNECTIONS

Installation procedures involving connection of power cables, batteries and earthing

must be performed according to local regulations.

1.3.2 SAFETY

All personnel involved in installation must read and understand the safety instructions

prior to installation, see the description document for SAFETY.

20/1531-ASP11301 Uen B5 2017-03-23 4

INSTALLING CABINET

2 INSTALLING CABINET

This section describes a full installation of hardware components in the BYB 501

cabinet. The recommended installation order is from the bottom of the cabinet to the

top.

Depending on the configuration, some pieces of hardware can be pre-installed. There-

fore, some installation steps may be irrelevant. In that case, ignore the irrelevant step

and proceed to the next one.

It is recommended to install the hardware at the cabinet locations described in the

instructions below. Although not recommended, it is possible to change the hardware

placement in the cabinet. In that case, the following constraints must be regarded:

• The batteries must be placed at the lowest position in the cabinet.

• The fan unit must always be installed directly above the subracks.

• Two subracks must be mounted closely, one above the other.

Note: The following instructions describe a hardware installation in the BYB 501

cabinet. When installing the hardware in other type of cabinets, refer to manu-

facturer instructions.

2.1 OVERVIEW

This section describes the hardware components in the MX-ONE, their functions, and

technical details as dimensions and weights.

The hardware components in the MX-ONE are mounted in 19-inch cabinet: the BYB

501 cabinet, the standard cabinet (locally sourced).

This document describes installation of hardware in the BYB 501. Most of the instruc-

tions are also relevant for installation in other 19-inch cabinets.

The hardware components include a variable number of power units, batteries,

subracks with extension boards, fan units, Media Gateways, and servers. The number

of components and their location in the cabinet vary according to customer needs.

For an example of an MX-ONE cabinet and its main hardware components, see Figure

1:MX-ONE Cabinets on page 5.

The components in the figure are:

AMX-ONE cabinet, BYB 501

BStandard cabinet (locally sourced)

CBattery string

DAC/DC unit

EDC/AC inverter (locally sourced)

FSubrack MX-ONE Lite

GSubrack MX-ONE Classic

HFan unit

IServers for the MX-ONE and MX-ONE Messaging

KMX-ONE Server

INSTALLING CHASSIS IN ACABINET

520/1531-ASP11301 Uen B5 2017-03-23

For information on technical details for the hardware components, see Table 1 Size,

Weight, and Voltage of MX-ONE Hardware on page 6.

Figure 1: MX-ONE Cabinets

20/1531-ASP11301 Uen B5 2017-03-23 6

INSTALLING CABINET

Table 1 Size, Weight, and Voltage of MX-ONE Hardware

1) Depending on configuration.

2) U = 44.45 mm = 1.75 inches

3) M = 25 mm = 0.98 inch

For information about power dissipation and power consumption, see the description

for POWER DISSIPATION.

The following flow diagram shows the installation procedure step-by-step. See Figure

2:Workflow for the MX-ONE Hardware Installation on page 7.

Pos Component Product

Number

Width, height,

and depth

(mm)

Weight

(kg)

Input

Voltage

Output

voltage

Heigh

t (U) 2)

Height

(M) 3)

A BYB 501

cabinet

600 x 1,800

x 400

B Standard

cabinet

Locally

sourced

C Battery 31

Ah (4

battery

blocks)

BKB 201

003/1

425 x 159 x

280

45 -48 V DC 4 7.2

Battery 62

Ah (4

battery

blocks)

BKB 201

003/2

425 x 264 x

280

82 -48 V DC 6 10.8

D AC/DC Unit 51305282 440 x 90 x

350

12.8 -

14.6 1)

90 - 250

V AC

-48 V DC 2 4

E DC/AC

Inverter

Locally

sourced

F MX-ONE Lite

(3U-chassis)

87L00039

BAA-A

440 x 130 x

235

3.9 1) -48 VDC or

115/240

VAC

35.4

G MX-ONE

Classic

LBP22 (7U)

BFD 761

40/1

450 x 310 x

315

6.6 – 14.0

-48 V DC 7 12.6

H Fan unit BFD 509

08/4

435 x 50 x

240

4.5 -48 V DC 1.2 2.2

I Standard

Server

KDU 137

xxx/x

463 x 44 x

693

23 100 – 240

V AC

1 not for

BYB

501

K MX-ONE

1U chassis

87L00032

BAA-A

440 x 45 x

220

2.2 1) -48 VDC

or 115/240

VAC

INSTALLING CHASSIS IN ACABINET

720/1531-ASP11301 Uen B5 2017-03-23

Figure 2: Workflow for the MX-ONE Hardware Installation

2.2 MOUNTING CABINETS

This section describes mounting of the cabinets. The instructions focus on the BYB 501

cabinets. For installation of the standard server cabinet, see the manufacturer instruc-

tions.

After this installation phase, all cabinets are positioned, fastened, leveled, and

anchored to the site floor.

2.2.1 UNPACKING

When unpacking the cabinet, perform the following steps:

1. Open the cabinet case using the Vikex opener.

2. Lift the cabinet using a cabinet hoist or at least four people.

3. Place the cabinet on the floor in an upright position. Take extra care to avoid the

cabinet from tipping over, as it is not yet secured to the floor.

4. Remove the plastic wrapping from the cabinet.

5. Move the cabinet to its position according to the floor marking, using a cabinet

lifter or at least four people.

20/1531-ASP11301 Uen B5 2017-03-23 8

INSTALLING CABINET

2.2.2 CABINET LAYOUT

Make sure all preparations for placement of cabinets at the site, including floor marking,

were done during the site planning stage, see the environmental spec for MX-ONE

SITE PLANNING.

For examples of cabinet layouts at the MX-ONE site, see the environmental spec for

MX-ONE SITE PLANNING.

2.2.3 MOUNTING SETS

This sections lists all the mounting sets used when mounting and grounding the BYB

501 cabinets. Refer to the relevant mounting set table in each installation step.

In the tables screws are named for example M 4X8, M 4 = metric thread 4 millimeters,

and 8 = 8 millimeters in length.

INSTALLING CHASSIS IN ACABINET

920/1531-ASP11301 Uen B5 2017-03-23

Table 2 Cabinet Frame (normally mounted)

2.2.4 POSITIONING THE CABINET

1. Make sure that holes for tip protection or earthquake bracing frame have been

drilled.

If not use the rack and the tip protection or the earthquake bracing frame as a

template.

2. Position the cabinet in line with other cabinets and the site walls, see the envi-

ronmental spec for MX-ONE SITE PLANNING.

1/BYB 501 180 Cabinet Frame

Pos. Title/Function Product Number Quantity

RACK FRAME, H=1800, METRIC, W=450 SXK 118 0444/1 1

MOUNTING BAR, H=1800, METRIC SXA 210 026/1 2

SCREW M 4X8 24/SBF 228 040/0080 24

A, B FOOT WITH ADJUSTING NUTS SXK 118 0159/1 4

DESIGNATION LABEL SVH 290 51/2 2

EARTHING PLATE SXA 123 0760/1 4

SCREW M 4X8 24/SBF 228 040/0080 8

PUSH-BUTTON SKY 117 01/4 2

SCREW 3.5X9.5 SBF 131 279/24 2

ESD WRISTSTRAP LYB 250 01/141 1

LABEL SVB 129 16 1

MARKING LABEL 2/SVF 191 040/2 1

MARKING PLATE2 SVF 191 131/1 1

20/1531-ASP11301 Uen B5 2017-03-23 10

INSTALLING CABINET

2.2.5 LEVELING THE CABINET

Figure 3: Leveling the Cabinet

1. Level the cabinet by adjusting the feet (A) using the 24-mm U-ring wrench, see

Figure 3:Leveling the Cabinet on page 10

2. Verify that the cabinet is leveled horizontally and vertically, using a water level.

3. Tighten the locking nuts (B) on all feet using the 24-mm U-ring wrench, see

Figure 3:Leveling the Cabinet on page 10

4. Proceed to the next installation stage:

• For installation of a cabinet with tip protection, see 2.2.6 Installing the

Cabinet with Tip Protection on page 9 .

• For installation of a cabinet with earthquake bracing frames, see 2.2.7

Installing the Cabinet with Earthquake Bracing on page 13 .

2.2.6 INSTALLING THE CABINET WITH TIP PROTECTION

Table 3 Mounting Set for Tip Protection

18/BYB 501/4 Tip protection, generic

s. Title/Function Product Number Quantity

A YOKE SXA 123 0786/1 2

B SPACER SXA 123 0788/1 6

C EXPANDER SCREW M 8X90 NSV 905 0805 4

D INSULATING WASHER SRB 186 080 4

E SUPPORT SXA 123 0785/1 4

F CLAMP2 SXA 123 0787/1 4

G NUT M 8 SBM 146 080/03 4

Andere Handbücher für MX-ONE

Inhaltsverzeichnis

Andere Mitel Konferenzsystem Handbücher

Mitel

Mitel UC360 Bedienungsanleitung

Mitel

Mitel 6863 SIP Bedienungsanleitung

Mitel

Mitel SmarT-1 EuroRoute Installationsanleitung

Mitel

Mitel Navigator 3300 ICP Konfigurationshandbuch

Mitel

Mitel 3300 Bedienungsanleitung

Mitel

Mitel MiVoice 5000 Bedienungsanleitung

Mitel

Mitel 3300 Konfigurationshandbuch

Mitel

Mitel MiVOICE BUSINESS Bedienungsanleitung

Mitel

Mitel SX-5 Bedienungsanleitung

Mitel

Mitel Navigator 3300 ICP Installationshandbuch

Mitel

Mitel ACD 2000 Bedienungsanleitung

Mitel

Mitel Inter-Tel 5000 Bedienungsanleitung

Mitel

Mitel 3300 Konfigurationshandbuch

Mitel

Mitel 5760 VC Bedienungsanleitung

Mitel

Mitel SX-200 Bedienungsanleitung

Mitel

Mitel MiVoice Business 3300 ICP Bedienungsanleitung

Mitel

Mitel MiVoice MX-ONE Bedienungsanleitung

Mitel

Mitel MiVOICE 6930 Bedienungsanleitung

Mitel

Mitel SX-200 ICP - 1.0 5020 Bedienungsanleitung

Mitel

Mitel UC360 Bedienungsanleitung

Mitel

Mitel 6600 Bedienungsanleitung

Mitel

Mitel 3300 Bedienungsanleitung

Mitel

Mitel MX-ONE Bedienungsanleitung

Mitel

Mitel Navigator 3300 ICP Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung