Mitel MiVoice MX-ONE Bedienungsanleitung

INSTALLATION INSTRUCTION

Installing MiVoice MX-ONE Hardware,

Overview

Catarina St enGöran Lannerg renGlobenMitelR&D MX-ONE & CMG

6/1531-ASP11301 Uen T2 2015-04-23 2

NOTICE

The information contained in this document is believed to be accurate in all respects

but is not warranted by Mitel Networks™ Corporation (MITEL®). Mitel makes no

warranty of any kind with regards to this material, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. The informa-

tion is subject to change without notice and should not be construed in any way as a

commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and

subsidiaries assume no responsibility for any errors or omissions in this document.

Revisions of this document or new editions of it may be issued to incorporate such

changes.

No part of this document can be reproduced or transmitted in any form or by any means

- electronic or mechanical - for any purpose without written permission from Mitel

Networks Corporation.

Trademarks

Mitel® is a registered trademark of Mitel Networks Corporation.

All trademarks mentioned in this document are the property of their respective owners,

®, TM Trademark of Mitel Networks Corporation

INSTALLING MIVOICE MX-ONE HARDWARE, OVERVIEW

36/1531-ASP11301 Uen T2 2015-04-23

1 INTRODUCTION

MX-ONE is a communication solution for enterprises. MX-ONE integrates voice

communication in fixed and mobile networks for public as well as private service.

MX-ONE can be integrated into an existing Local Area Network (LAN) infrastructure.

MX-ONE supports both IP telephony and functions found in classic circuit-switched

PBXes (Private Branch Exchanges).

1.1 SCOPE

This document describes the MX-ONE installation procedure structure and shows the

steps needed for a HW installation. For details of each area, see the following docu-

ments:

• Installation preparation and Earthing, 19/1531-ASP11301

• Installation chassis in a Cabinet, 20/1531-ASP11301

• Installation boards and Cabling, 21/1531-ASP11301

1.2 TARGET GROUP

The target group for this document is personnel involved in installing the MX-ONE.

1.3 PREREQUISITES

This section lists requirements that must be fulfilled before the installation starts.

1.3.1 TRAINING

Personnel working with Mitel MX-ONE systems must have the training required to

perform their tasks correctly.

It is recommended for engineers installing the MX-ONE to be acquainted with the

following areas:

• MX-ONE Service Node

• Media Gateway in MX-ONE

• Certification

• TCP/IP Networks

1.3.2 ELECTRICAL CONNECTIONS

Installation procedures involving connection of power cables, batteries and earthing,

must be performed according to local regulations.

6/1531-ASP11301 Uen T2 2015-04-23 4

INTRODUCTION

1.3.3 SAFETY

All personnel involved in installation must read and understand the safety instructions

prior to installation, see the description document for SAFETY.

1.3.4 SITE PLANNING

Read through each device installation documentation, and from there, conclude where

the equipment shall be installed.

For MX-ONE, an analogue trunk line generates a touch or leakage current which if

there are several analogue trunk lines installed, it calls for the installation to be in a

“Restricted Access Location”. The MX-ONE 3U and 7U chassis are marked with a

warning text “High voltage current...” to reflect this.

1.3.5 GROUNDING AND EARTHING

In this document the expressions grounding and earthing have the same meaning.

INSTALLING MIVOICE MX-ONE HARDWARE, OVERVIEW

56/1531-ASP11301 Uen T2 2015-04-23

2 OVERVIEW MIVOICE MX-ONE PRODUCTS

2.1 BOARDS IN MIVOICE MX-ONE

The following circuit boards can be used in the exchange. For technical data about the

boards, see document 20/1531-ASP11301, INSTALLATION CHASSIS IN A CABI-

NETT

Table 1 Boards

Note: When ASU is stated, it means all versions of ASU, ASU Lite and ASU-II.

Board Product number Information

ALU2 ROF 137 5373/11 Alarm unit for external alarms

ASU ROF 137 6307/21 Mitel Server Unit, 4GB

ASU ROF 137 6307/22 Mitel Server Unit. 8GB

ASU Lite ROF 137 6307/31 Mitel Server Unit, Lite. 4GB

ASU-II ROF 137 6307/4 Mitel Server Unit. 16GB

DC/DC ROF 137 6303/1 Power unit

ELU26 ROF 137 5321/12 ISDN-S digital extensions

ELU31 ROF 137 5412/4 DECT extensions, Base stations

ELU33 ROF 137 5062/1 Digital extensions

ELU34 ROF 137 5064/x Analog extensions with message waiting

FTU2 ROF 137 5415/11 Failure Transfer Unit

MFU ROF 137 5348/x Multi frequency unit

MGU ROF 137 6304/x Media Gateway Unit, 8 E1/T1

MGU2 ROF 137 6304/4 Media Gateway Unit, 4 E1/T1

TLU76 ROF 137 5338/x Digital trunk, ISDN, E1, DPNSS, CAS, SS7

TLU77 ROF 137 5387/x ISDN, T1, DPNSS, CAS depending on version

TLU79 ROF 137 5349/11 ISDN-T 2B+D trunk line

TLU80 ROF 137 5406/11 4-wire analog trunk using E&M signaling. NOTE !! This

board can only be used in MX-ONE Classic (7U). Not in

MX-ONE Lite (3U) or the 1U-chassis.

TLU83 ROF 137 6305/1 Analog trunk line (loop start, ground start. CLI with FSK

and DTMF)

TLU83 ROF 137 6305/2 Analog trunk line (loop start, ground start, call metering.

CLI with FSK and DTMF)

TLU83 ROF 137 6305/3 Analog trunk line (loop start, ground start, CLI with

DTMF)

TMU ROF 137 5335/x Tone and Multi part Unit. DTMF

6/1531-ASP11301 Uen T2 2015-04-23 6

OVERVIEW MIVOICE MX-ONE PRODUCTS

2.2 MITEL MX-ONE CHASSIS

2.2.1 MX-ONE 1U CHASSIS, PROD NO. 87L00032XAA-A

The MX-ONE 1U (prod. No. 87L00032xAA-A) is a 1U high subrack with space for 1pcs

of 40mm board or 2 pcs of 20mm boards mounted horizontally. It has 3 cooling fans

(on the left hand side).

Figure 1: The MX-ONE 1U chassis equipped with MGU2 and ELU34

The 1U chassis are available in two versions: 87L00032AAA-A with only -48VDC inlet,

and 87L00032BAA-A with both -48VDC and 115/230VAC. All inlets are on rear side.

The mounting brackets can be rotated to support either metric or 19-inch rack systems.

Note: There is no -5V provided in the backplane which means that e.g. TLU80 can not

be used together with MX-ONE 1U chassis.

Note: The maximum power supply is 125 W.

For power calculations see document POWER DISSIPATION.

2.2.2 MX-ONE LITE, 3U CHASSIS, PROD NO. 87L00039XAA-A

This MX-ONE Lite is a subrack with boards mounted horizontally, and 2 pcs of cooling

fans (on the left hand side). The chassis can be equipped with up to 6pcs of 20mm

boards.

MX-ONE Lite has board positions/Time slots 00, MGU/10, 20, 30, 40 and 50 counted

from lowest position.

See Figure 2:MX-ONE Lite, 87L00039AAA-A, equipped with MGU2, ASU and 3 addi-

tional boards on page 7.

The chassis have a Fan unit that is easily switched if needed.

Note: Slot MGU/10 can only be used for MGU boards.

Note: The unit has replaceable fuses on the -48 V power supply voltages One (1) on

the -48 V input and one (1) from the internal AC/DC power supply.

Note: There is no -5V provided in the backplane which means that e.g. TLU80 can not

be used together with MX-ONE Lite.

If a 40mm building height server board (ASU) is installed, together with MGU2 with its

20mm front, three slots are left for an arbitrary MX-ONE board, for example an ELU33,

ELU34 and TMU/12. See Figure 2:MX-ONE Lite, 87L00039AAA-A, equipped with

MGU2, ASU and 3 additional boards on page 7.

Note: The maximum power supply is 250 W.

For power calculations see document POWER DISSIPATION.

INSTALLING MIVOICE MX-ONE HARDWARE, OVERVIEW

76/1531-ASP11301 Uen T2 2015-04-23

Figure 2: MX-ONE Lite, 87L00039AAA-A, equipped with MGU2, ASU and 3

additional boards

2.2.3 MX-ONE CLASSIC, 7U CHASSIS

In the MX-ONE Classic (prod. No. BFD76140/x) the boards are mounted vertically in

this 19 inch wide subrack. This chassis need additional Fan Unit. See 2.2.4 Fan Unit

(for 7U chassis) on page 7. The chassis can only be feed by -48V in the front of the

DC/DC-board.

The MGU board goes in the middle at a dedicated position. It is recommended to place

the ASU on the right side of the MGU.

The MX-ONE Classic has time slots marked on the top label. The marking is 00, 10,...,

70 starting from board position 01 and from board position 45. These positions are

intended for the device boards.

Figure 3: MGU2 and ASU in the 7U high,19 inch chassis

2.2.4 FAN UNIT (FOR 7U CHASSIS)

The fan unit provides forced cooling of the MX-ONE Classic media gateway boards in

the 7U chassis. One fan can be used to serve two 7U- subracks on top of each others.

Time

slot

MGU/10

6/1531-ASP11301 Uen T2 2015-04-23 8

OVERVIEW MIVOICE MX-ONE PRODUCTS

Figure 4: Fan Unit

2.3 SERVERS

There are several types of servers used in the MX-ONE. The ASU Servers in three

versions and the Standard Servers.

For technical data about the servers, see document INSTALLATION CHASSIS IN A

RACK.

Figure 5: ASU in a MX-ONE 1U chassis

The ASU Server consists of an Server board (ASU) slided into the MX-ONE 1U

chassis.

2.4 AC/DC POWER UNITS

The AC/DC power units converts the power from the AC power supply network (mains)

to DC output for the batteries and for the DC/DC converter board in the subracks.

For installation of these Power Units it is important to follow the suppliers Installation

Instructions/Manuals.

2.4.1 BZA10911/1, 2U POWER UNIT

This 2U height Power Unit is delivered with a 800W rectifier module. Up to 4 rectifiers

can be mounted (3200W). It is also equipped with Controller and a Load and Battery

distribution modules. See Figure 6:2U height AC/DC Power Unit, 800 - 3200W on page

INSTALLING MIVOICE MX-ONE HARDWARE, OVERVIEW

96/1531-ASP11301 Uen T2 2015-04-23

Figure 6: 2U height AC/DC Power Unit, 800 - 3200W

2.4.2 87L00034AAA-A, 1U POWER UNIT

The Aspiro 1U height Power Unit is delivered with one 800W rectifier module with a

spare slot for one extra rectifier to support a total of 1600W. An optional kit with

Controller (PCC) and cables for battery is available.

Note: The PCC is needed to control batteries.

Figure 7: 1U height AC/DC Power Unit, 800-1600W

2.5 BATTERY STRING

The batteries provide backup power to the system. Two types of batteries are available,

31 Ah and 62 Ah.

Figure 8: Batteries (62 Ah) and Battery Shelf

For technical data about the batteries, see document INSTALLATION CHASSIS IN A

RACK.

2.6 CABLES

Cables for each board, power and batteries see document 21/1531-ASP11301

INSTALLATION BOARDS AND CABLING.

6/1531-ASP11301 Uen T2 2015-04-23 10

ENVIRONMENTAL REQUIREMENTS

3 ENVIRONMENTAL REQUIREMENTS

Read through each device installation documentation, and from there, conclude that all

of the equipment can be installed.

For MX-ONE, an analogue trunk line generates a touch or leakage current which if

there are several analogue trunk lines installed, calls for the installation to be in a

“Restricted Access Location". The 3U and 7U chassis are marked with a warning text

"High voltage current..." to reflect this.

Note: Values below are relevant for MX-ONE products. For other products see

suppliers Technical Specification.

The exchange room must meet the following requirements:

• The air shall not contain any dust, smoke, gases or acid fumes

• Temperature +5 to +40 oC (+41 to +104 oF)

• Relative air humidity 20-80%

• The relationship between temperature and air humidity shall not cause conden-

sation

• The equipment must not be exposed to direct sunlight

• Make sure that the floor withstands the mass of the PBX

• For concrete floor, the distributed load is the total mass of equipment in the room

divided by the area of the room

• For wooden floor, extra caution must be taken concerning the spot load of the

cabinets

• The floor should be covered by an earthed anti-static carpet in order to reduce

the risk of the exchange being exposed to interference caused by static elec-

tricity

If the batteries are to be installed in the exchange room, they must be of a type which

does not produce gases or acid fumes.

If the batteries are to be installed in a room outside the exchange room, the environ-

mental conditions must comply with the battery suppliers instructions.

The PBX operators room should be of standard office design, but the floor as in the

exchange room should be covered by an anti-static carpet.

Andere Handbücher für MiVoice MX-ONE

Inhaltsverzeichnis

Andere Mitel Server Handbücher

Mitel

Mitel Aastra 470 Benutzerhandbuch

Mitel

Mitel Aastra 470 Benutzerhandbuch

Mitel

Mitel 6500 Anleitung zur Verwendung

Mitel

Mitel Speech Server Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung