Mitsubishi Electric PAC-DRP10DP-E Bedienungsanleitung

Air Conditioning For Building Application

Drain Water Lift-Up Kit PAC-DRP10DP-E

Installation Manual

This installation manual contains only the description of how to install the Drain water Lift-Up Kit PAC-DRP10DP-E. For information

about how to wire and how to install air conditioning units, see the installation manual for them.

For your safety, first be sure to read section 1. "Safety Precautions" below thoroughly and then install the Drain water Lift-Up Kit

PAC-DRP10DP-E correctly.

1. Safety precautions

• The following two symbols are used to denote dangers that may be caused by incorrect use and their degree:

WARNING This symbol denotes what could lead to serious injury or death if you misuse the PAC-DRP10DP-E.

CAUTION This symbol denotes what could lead to a personal injury or damage to your property if you misuse the

PAC-DRP10DP-E.

• After reading this installation manual, keep it in a place where the final user can see it anytime he or she wants to it.

When someone moves, repairs, or uses the PAC-DRP10DP-E, make sure that this manual is forwarded to the final user.

WARNING

Always have the unit installed by Authorized Mitsubishi

Representative or similar professional.

Improper installation by the user could result in problems such as

water leakage, electric shock or fire.

Always use the designated cables and connect them properly.

When connecting the terminals, make sure that external forces

from the cable is not being conveyed to the terminal and then

tighten it securely.

Improper or loose connections could cause excessive heat or fire.

Only use Mitsubishi-approved accessories, such as an air

cleaner, humidifier or electric heater.

Always have such accessories installed by an Authorized Mitsubishi

Representative or similar professional. Improper installation by the

user may result in water leakage, electric shock or fire.

Install the unit according to this Installation Manual.

If the unit is installed improperly, water leakage, electric shock or fire

may result.

Have all electric work performed by a properly licensed

electrician. Electric work should be performed in strict adherence

to procedures to this Installation Manual. Always provide a

dedicated power supply.

If the capacity of the power supply is inadequate, it could result in

problems such as electric shock or fire.

Never modify the unit and always have repairs performed by an

Authorized Mitsubishi Representative.

Improper repair could result in problems such as water leakage,

electric shock or fire.

CAUTION

PRECAUTIONS BEFORE INSTALLATION

Never use for special applications such as storing food, plants,

precision equipment or art.

The quality of these items may deteriorate.

Never use the unit in special environments.

Special environments with high concentrations of oil, steam or sulfuric

gases will reduce the performance of the air condition and cause its

parts to deteriorate.

Never install the unit where run-off could result in damage.

If the humidity in the room exceeds 80% or if the drain becomes

clogged, water may drain off of the indoor unit. When the unit is used

for heating, there may be drainage from the outdoor unit. If required,

provide collector drain for the outdoor unit.

Always provide adequate signal noise protection when installing

in facilities such as hospitals and communication stations.

Equipment at these facilities, such as inverters, in-house generators,

high-frequency medical equipment, two-way communication

equipment, may cause the air conditioner to operate improperly.

Conversely, the signal noise from the air conditioner may affect

the operation of medical equipment and two-way communication

equipment and this could interfere with the medical treatment being

given a patient or cause disturbances or interference in video

broadcasting equipment.

PRECAUTIONS BEFORE REMOVE AND ELECTRIC WORK

Route wiring so that there is no tension.

Tension could cause the wire to break and this could result in

excessive heat or fire.

Dispose of packing materials properly.

Use care when transporting the unit.

• Always use two or more people for lifting a product weight 20 kg or

more.

• Some products are packaged with plastic wrapping bands. Never use

these for lifting or transporting the product.

• Never touch the fins on the heat exchanger. They are sharp and

could cause cuts.

• Never allow children to play with the plastic bags used for packaging.

Always tear them up when disposing. A child could suffocate in these

bags.

PRECAUTIONS BEFORE TEST RUN

Never touch the switch with wet hands.

Electric shock could occur.

Never operate the air conditioner with the panel or guard

removed.

The hand could come in contact with rotating, hot or high-pressure

components. They could cause electrical shock or entanglement.

Never operate the air conditioner with the air filter removed.

Particles will enter into the air conditioner and cause damage.

Never turn off the power supply immediately after stopping the

unit.

Wait five minutes or more before turning off the power supply. Turning

off the power supply before that time could result in water leakage or

damage.

2. Confirming the Supplied Parts

1. Model names and applicable models

Model name Applicable types

PAC-DRP10DP-E PEFY-P40VMH-E2, PEFY-P50VMH-E2, PEFY-P63VMH-E2, PEFY-P71VMH-E2

PEFY-P80VMH-E2, PEFY-P100VMH-E2, PEFY-P125VMH-E2, PEFY-P140VMH-E2

2. Provided parts

Check that the packet includes the following parts in addition to this installation manual.

PARTS 1 DRAIN PUMP ASSY. 2RUBBER PLUG 3 BAND 4PTT SCREW 4×10

SHAPE

Q'TY 1 1 2 2 + 1 (spare)

Drain socket

Drain sensor

3. Attach the Drain Pump

The drain pump must be attached before installation of the indoor unit.

3-1. Preparation for the indoor unit

(1) Remove the fixing screws (2 locations) shown in Fig. 3-1, and remove the

control box cover.

Fig. 3-1

(2) Remove the fixing screws (5 locations) shown in Fig. 3-2, and remove the

maintenance cover.

Fig. 3-2

(3) Remove the fixing screws (2 locations) shown in Fig. 3-3, and remove the

Drain socket hole cover.

* These screws will be reused to fix the drain socket. Keep them in a safe

place.

Fig. 3-3

3-2. Attach the drain pump

(1) Attach the drain pump assy 1 and drain socket as shown in Fig. 3-4 using

four PTT screws 4.

* When attaching the drain socket, make sure that drain hose is straight.

(2) Attach the Rubber Plug 2.

Fig. 3-4

Control box cover

Fixing screw

Maintenance cover

Fixing screws

Drain socket hole cover

Drain socket

Drain pump assy 1

Rubber Plug 2

3-3. Attach the drain socket

As shown in Fig. 3-5, insert the drain socket into the U-shaped cutout.

Fig. 3-5

4. Wiring

1. Passing the pump wires (Fig. 4-1)

(a) Route the 2 wires so that they pass through the raised part when the

maintenance cover is installed.

Fig. 4-1

2. Connecting the pump wires to the control box of the indoor unit (Fig. 4-2)

(a) Insert the white connector into CN31 on the indoor P.C. board.

Since a connector has been inserted into both CNP and CN31 before

shipment, they must be removed.

(b) When wiring is complete, fasten the remaining cords with the band 3.

Fig. 4-2

When fastening lead wires

Power wires and low-voltage wires are separated inside the control box to prevent noise. Lead wires from the Drain Water Lift-

Up Kit also need to be separated, so fasten them to the lead wires located inside the control box as described below.

• Since the yellow wire is used for power, its remaining portion must be fastened to the lead wires from the power terminal block.

• Since the clear wire is used for low voltage, its remaining portion must be fastened to the pipe sensor lead wire.

PTT screw 4

Drain socket

Frame

From drain pump

Yellow wire

Clear wire

From drain sensor

Raised part

CNP

Blue White

CN31

from drain pump

Yellow wire

Indoor P.C.

board

Clear wire

from drain sensor

5. Drain piping work

(1) Ensure that the drain piping is downward (pitch of more than 1/100) to

the outdoor (discharge) side. Do not provide any trap or irregularity on

the way. (Fig. 5-1)

(2) Ensure that any cross-wise drain piping is less than 20 meters

(excluding the difference of elevation). If the drain piping is long,

provide support bracket to prevent it from waving. Never provide any

air vent pipe. Otherwise drain may be ejected.

(3) Use a hard vinyl chloride pipe ø32 mm (1-1/4 inch) for drain piping.

(4) Ensure that collected pipes are 10 cm lower than the unit body’s drain

port. (Fig. 5-2)

(5) Do not provide any odor trap at the drain discharge port.

(6) Put the end of the drain piping in a position where no odor is

generated.

(7) Do not insert the end of the drain piping into any sewer where sulfuric

gases are generated.

(8) The intake of the drain piping can be made 55 cm higher than the

Indoor unit. If there are some obstacles under the ceiling, use elbows

to make it at least height according to the site. (Fig. 5-3)

(9) Be sure to use the supplied drain hose (Accessory).

Connect each connection with vinyl chloride adhesive. But never use

any adhesive over the indoor unit discharge port. Otherwise the Drain

Water Lift-Up Kit cannot be serviced later. Also, the end connection

may be eroded by resin and so cracked.

Note:

If the rise portion is long, there will be a lot of returned water in

an operation stop, generating slime or odor during off-season.

Ensure that the rise portion is at a minimum.

CAUTION

Pipe the drain piping to ensure that it discharges drain, and

insulate it to prevent dew condensation. A failure to the piping

work may cause water leakage and so wet your property.

25 cm

1.5 – 2 m

Fig. 5-1

Fig. 5-2

Fig. 5-3

Downward pitch of

more than 1/100

Support bracket

Insulation

Take as large as possible. About 10 cm.

Indoor

unit

Indoor

unit

Collective piping

Indoor

unit

Hard vinyl chloride 90˚

elbow (field supply)

Hard vinyl

chloride

(ø32 mm)

(field supply)

Drain hose

(Accessory)

Hard vinyl chloride

90˚ elbow

(field supply)

Tie band (small)

(Accessory)

Indoor unit

Less than 300 mm

Less than 550 mm

6. Confirming drain discharge

►MakesurethattheDrainWaterLift-UpKitoperatesnormallyfordischargeandthatthereisnowaterleakagefromthe

connections.

• Be sure to confirm the above in a period of heating operation.

• Be sure to confirm the above before ceiling work is done in the case of a new construction.

(1) Turn on the SWE on the control board.

(2) Pour water into the drain pan using a kettle etc.

When pouring, make sure that the spout of the kettle is placed into the

drain pan to prevent water overflowing from the drain pan.

(Fig. 6-1)

(3) Turn on the main power of the indoor unit.

The drain pump will be forced to operate even if no remote controller

operation is performed.

Check the transparent drain socket to make sure that drain is

discharged.

(4) When it is confirmed that drain is discharged properly, turn off the main

power, and turn off the SWE on the control board.

* If the SWE remains turned on, the drain pump will be caused to

operate all the time, so make sure that it is turned off.

* The SWE must not be kept on for longer than 4 hours.

Check that all the wiring work has been completed. If so, reassemble the

covers in reverse order.

(refer to 3-1 (2)→(1))

Fig. 6-1

Drain socket

Inlet water

VN79D552H02

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Klimaanlage Handbücher

Mitsubishi Electric

Mitsubishi Electric SUZ-M-VA Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PURY-(E)P-YLM-A (-BS) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MUZ-SF25VE-E1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-8A140VA Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MS-GK30VAT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric City Multi PMFY-P-VBM-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric SEZ-KD25 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PEAD-SM71JA(L) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MUZ-D-NA Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUZ-A-NHA3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric SUZ-KA35VA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-GE22VA Handbuch

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PLA-SM71EA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-4C36NAHZ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-FA25VA-E1 WH Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MSZ-GE09NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSH-XV07UV Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PKA-A12HA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSH09NW 2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-RP35BA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-ZM100EA2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric TRANE NTXWEL09A112A Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-4F83VFHZ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr. SLim SEZ-KD09NA Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung