Mitsubishi Electric SW0DNC-MNETH-B Bedienungsanleitung

MELSECNET/H Interface Board

User's Manual (For SW0DNC-MNETH-B)

-Q80BD-J71LP21-25

-Q80BD-J71LP21S-25

-Q81BD-J71LP21-25

-Q80BD-J71LP21G

-Q80BD-J71BR11

A - 1 A - 1

SAFETY PRECAUTIONS 

(Be sure to read these instructions before using the product.)

Before using this product, read this manual and the relevant manuals introduced in this manual carefully

and handle the product correctly with full attention to safety.

Note that these precautions apply only to this product. Refer to the user's manual of the CPU module for

safety precautions on programmable controller systems.

In this manual, the safety instructions are ranked as " WARNING " and " CAUTION".

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Note that failure to observe the !CAUTION level instructions may also lead to serious results depending

on the circumstances.

Be sure to observe the instructions of both levels to ensure personal safety.

Please keep this manual in accessible place and be sure to forward it to the end user.

[Design Instructions]

!WARNING

Make sure to see this manual for information about each station's operating status when a

communication error occurs in the network. Erroneous outputs and malfunctions may result in

serious accidents.

If a coaxial cable is disconnected, this may destabilize the line, and a data link communication

error may occur in multiple stations. Make sure to create an interlock circuit in the sequence

program so that the system will operate safely even if the above error occurs. Failure to do so

may result in a serous accident due to faulty output or malfunctions.

Provide a safety circuit outside the programmable controller so that the entire system will

operate on the safety side even when an error occurs with the personal computer.

There is a risk of an accident due to faulty output or malfunctioning.

(1) Construct circuits outside the programmable controller, including an emergency stop circuit,

protection circuit, interlock circuit for reciprocal operations such as forward and reverse, and

interlock circuit for positioning high and low limits to prevent damage to the equipment.

(2) If the station in which the board is installed is disconnected from the data link due to a data

link error, the data output from that station and written in other stations will remain the same

as immediately before the error occurred in the data link. This data will be retained until the

data link for that station is reopened (returned to system).

Provide a mechanism to monitor the status of data link and handle errors for each station

that is connected to the data link system.

A - 2 A - 2

[Design Instructions]

!CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause malfunctioning.

[Installation Instructions]

!CAUTION

Use the board in an environment as described in the general specifications listed in this

operating manual.

If the board is used in an environment outside the ranges described in the general

specifications, it may result in an electric shock, fire, malfunctioning, damage to or deterioration

of the product.

Be sure to shut off all phases of the external power supply used by the system before installing

or removing the board. If all power is not turned off, this will result in failure of the board or

malfunctioning.

Install the board to a personal computer which is compliant with PCI standard or PCI ExpressR

standard (Refer to "Section 2.5 Operating Environment"). Failure to do so may cause a failure or

malfunction.

Securely mount the board to the PCI slot of the mounting device.

If the board is not mounted correctly, this may lead to malfunctioning, failure or cause the board

to fall.

Insert the communication cable securely into the board connector. After it has been inserted,

check to make sure that it is not being lifted up.

A faulty connection can lead to faulty input or output.

When mounting the board, take care not to become injured by the components that are installed

or surrounding materials.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the board.

Failure to do so may cause a failure or malfunctions of the board.

When installing the board, take care not to contact with other boards.

A - 3 A - 3

[Wiring Instructions]

!WARNING

Be sure to shut off all phases of the external power supply used by the system before

performing work such as installing the board and wiring.

If all power is not turned off, there is a risk of electric shock or damage to the product.

When turning on the power and operating the module after having installed the board and doing

the wiring, always attach the cover for the device module in which the board is installed.

There is a risk of electric shock if the module cover is not attached.

!CAUTION

Properly solder the parts of a soldering-type coaxial cable connector. Incomplete soldering may

result in malfunction.

Crimp the parts of a crimping-type coaxial cable connector with proper force at a proper position.

Failure to do so may cause drop of the cable or malfunction.

For the communication cable, specialized skills and tools are required to connect the plug and

cable. The connector plug itself is a custom part.

When purchasing, consult your local Mitsubishi representative.

If the connection is incomplete, this can result in a short, fire or malfunction.

Be sure to fix communication cables connecting to the board by placing them in the duct or

clamping them.

Cables not placed in the duct or without clamping may be hang freely and accidentally pulled,

which may cause damage to the board or cable, or malfunction due to bad cable contacts.

When removing the cable from the board, do not pull the cable.

Pulling the cable that is still connected to the board may cause damage to the board or cable, or

malfunction due to bad cable contacts.

Prevent foreign matter such as chips or wiring debris from getting on the board.

Failure to do so can result in fire, breakdowns or malfunction.

Verify the rated voltage and pin assignment of the product and connect the external power

supply cable properly.

Connecting a power supply with a different voltage rating, imperfect cable crimping or faulty

wiring may cause a fire or failure.

Use a specified tool for crimping of the cable and contacting pin. Imperfect crimping may cause

malfunction.

Verify the pin assignment and fully insert the crimped contacting pin into the connector.

Imperfect insertion may cause failure or malfunction.

Insert the wired external power supply cable into the external power supply cable connector until

a click is heard. Imperfect insertion may cause failure or malfunction.

Keep the external power supply cable away from the main circuit cable, power cables and/or

load cables connected to other than programmable controllers. Ensure a distance of 100mm

(3.94 in.) between them. Failure to do so may result in malfunction due to noise, surge or

induction.

Always ground the personal computer. Failure to do so may cause malfunction.

A - 4 A - 4

[Startup/Maintenance Instructions]

!WARNING

Do not attach or remove the communication cable while the power supply is on.

This may result in malfunctioning.

Tighten the board fixing screws after turning off the power supply.

There is a risk of electric shock if the screws are tightened while power is on.

!CAUTION

Thoroughly read the operating manual and carefully check to make sure everything is safe

before performing operations such as making changes to the program while the module is

operating, forced outputs, RUN, STOP and PAUSE.

Operation errors will result in damage to the equipment or accidents.

Do not dismantle or rebuild the board.

This will result in breakdowns, malfunctioning, injury or fire.

Be sure to shut off all phases of the external power supply used by the system before installing

or removing the board.

If all power is not turned off, this will result in failure of the board or malfunctioning.

The board internal microprocessor reaches very high temperatures when it is running. Do not

touch it directly when replacing the board.

This will result in breakdowns, malfunctioning or injury.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the board.

Failure to do so may cause a failure or malfunctions of the board.

[Disposal Instructions]

!CAUTION

When disposing of this product, treat it as industrial waste.

A - 5 A - 5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION

NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING

CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL

BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A - 6 A - 6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Nov., 2000 SH (NA)-080128-A First printing

Mar., 2001 SH (NA)-080128-B Model addition

Q80BD-J71LP21G, Q80BD-J71LP21GE

Correction

Section 1.3, Appendix 3.1

Jun., 2001 SH (NA)-080128-C Correction

About the Generic Terms and Abbreviations, Section 1.2, Section 1.3,

Section 2.5, Section 7.1, Section 7.1.1, Section 7.1.2, Section 7.4,

Section 8.2.3, Section 9.1.2, Section 9.2, Section 10.3.2, Section 10.4,

Appendix 3, Appendix 3.1

Addition

Section 10.8, Section 12.2, Chapter 13

Jan., 2002 SH (NA)-080128-D Correction

Section 2.5, Section 3.1, Section 3.2, Section 5.6, Section 9.1.2,

Section 10.7, Section 12.2, Section 12.2.2

Addition

About the Generic Terms and Abbreviations, Sections 9.1.2,

Chapter 13

Dec., 2002 SH (NA)-080128-E Correction

Safety Precautions, Section 8.2.3, Section 8.2.8, Section 8.3.3,

Section 9.1.2, Chapter 10, Section 12.2, Appendix 3.1, Appendix 4.1,

Appendix 4.2

Addition

Precautions for use, Generic Terms and Abbreviations, Section 1.2,

Section 1.3, Section 2.5, Section 5.4.2, Section 7.1.1, Section 7.1.2,

Section 7.2, Section 7.3, Section 8.1.1, Section 10.3, Chapter 13,

Section 14.3, Section 14.3.1, Section 14.5.4, Section 14.6

May, 2004 SH (NA)-080128-F Correction

Safety Precautions, Precautions for use, Section 3.1, Section 3.2,

Section 6.3.1, Section 8.2.5, Section 8.2.10, Section 12.2, Section 12.2.1,

Section 12.2.2, Section 12.2.3, Section 12.3.3, Chapter 13,

Section 14.4.4, Section 14.7, Appendix 5.1

Addition

Generic Terms and Abbreviations, Section 1.2, Section 1.3, Section 2.4,

Section 2.5, Section 4.2.1, Section 5.2.1, Section 5.3, Section 5.4.3,

Chapter 6, Section 6.3.6, Section 8.2.1, Section 8.2.3, Section 10.3,

Section 10.3.3, Section 10.3.4, Section 10.8, Section 11.3, Chapter 12,

Section 14.4, Section 14.5.5, Section 14.6, Appendix 3

A - 7 A - 7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Dec., 2004 SH (NA)-080128-G Chapter numbers of 5 to 14 were changed to 6 to 15 respectively.

Correction

Precautions for use, Generic Terms and Abbreviations, Chapter 1,

Section 1.1, Section 1.2, Section 1.3, Section 2.1, Section 2.4,

Section 2.5, Section 3.2, Chapter 7, Section 7.1, Section 7.2.4,

Section 9.2.2, Section 9.2.3, Section 9.2.5, Section 9.2.10,

Section 9.2.11, Section 10.1.2, Section 10.2, Section 13.2.1,

Section 15.4.3

Addition

Section 2.6, Chapter 5, Section 15.7

Jun., 2005 SH (NA)-080128-H Model addition

Q80BD-J71LP21S-25

Correction

SAFETY PRECAUTIONS, INTRODUCTION,

Generic Terms and Abbreviations, Product List,

Section 1.2, Section 2.1, Section 2.5, Section 3.2, Section 4.1,

Section 6.1, Section 6.3, Section 6.4, Section 6.5, Section 6.6,

Section 7.2.1, Section 8.1.2, Section 9.2.2, Section 9.2.6,

Section 9.3.5, Section 11.4, Section 11.6, Section 12.3, Chapter 13,

Chapter 14, Section 15.2, Section 15.4.4, Section 15.6, Section 15.7,

Section 15.8, Appendix 4, Appendix 5

Addition

Section 6.4.4, Section 15.6, Appendix 4, Appendix 6.2

Jul.,2005 SH(NA)-080128-I

Correction

Section 2.5, Appendix 6.2

Oct.,2005 SH(NA)-080128-J

Correction

Section 2.5, Section 8.1.1, Section 8.1.2, Section 8.3, Section 9.1,

Section 15.2

Mar., 2007 SH(NA)-080128-K Correction

Generic Terms and Abbreviations, Section 2.2.4, Section 2.5,

Section 6.4.1, Section 6.4.2, Section 8.1.1, Section 8.1.2, Section 10.1.2,

Section 10.2, Section 11.2, Section 11.6, Section 11.8, Section 15.4.5

Addition

Section 11.3.5, Section 11.3.6, Section 11.7

Oct., 2007 SH(NA)-080128-L Correction

Generic Terms and Abbreviations, Section 1.2, Section 1.3, Section 2.5,

Chapter 5, Section 8.1.1, Section 8.3, Section 9.1, Chapter 14,

Section 15.2, Section 15.3.1

Section 8.1.2 changed to Section 8.1.3

Addition

Section 8.1.2, Appendix 5

Jan., 2008 SH(NA)-080128-M Correction

Generic Terms and Abbreviations, Section 2.5, Section 6.5.1,

Section 6.5.2, Section 6.5.3, Section 6.6.1, Section 6.6.2, Section 8.1.1,

Section 8.1.3, Section 10.1.2, Section 10.2, Section 11.6, Section 11.7

A - 8 A - 8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

May, 2008 SH(NA)-080128-N Model addition

Q81BD-J71LP21-25

Correction

SAFETY PRECAUTIONS, Precautions for Use, INTRODUCTION,

Generic Terms and Abbreviations, Product List, Section 1.2,

Section 1.3, Section 2.1, Section 2.5, Section 3.1, Section 3.2,

Section 6.3, Section 6.4.1, Section 6.4.3, Section 6.5.1, Section 6.5.2,

Section 6.5.3, Section 6.6.1, Section 6.6.2, Section 8.1.1, Section 8.1.3,

Section 8.2, Section 8.3, Section 9.1, Section 9.1.1, Section 9.2.2,

Section 9.2.6, Section 10.1.2, Section 11.3, Section 15.2, Section 15.3,

Section 15.4.4

Appendix 3 to 6 changed to Appendix 2 to 5

Addition

Appendix 5.4

Deletion

Appendix 2, Appendix 2.1

Jun., 2008 SH(NA)-080128-O Correction

Section 1.3, Section 2.5, Section 9.2.4, Section 15.4.4,

Appendix 4.2

Oct., 2008 SH(NA)-080128-P Addition

Generic Terms and Abbreviations, Section 2.5, Section 10.1.2

Jul., 2009 SH(NA)-080128-Q Addition

Product List, Chapter 5, Appendix 4.1

Oct., 2009 SH(NA)-080128-R Addition

Section 8.1.3, Section 11.4, Section 13.3.4, Section 15.2

Correction

SAFETY PRECAUTIONS, Section 2.6, Section 4.1, Section 11.6,

Section 11.7, Section 12.1.1, Section 13, Section 13.1, Section 14

Dec., 2010 SH(NA)-080128-T Correction

Section 2.5

Mar., 2011 SH(NA)-080128-U Addition

Appendix 2

Correction

Product List, Chapter 7, Section 9.2.2, Section 15.2, Appendix 1,

Appendix 5.2

Appendix 3 to 6 changed to Appendix 4 to 7

May, 2011 SH(NA)-080128-V Correction

Precautions for Use, Chapter 8

Deletion

Section 8.3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Computerhardware Handbücher

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q80BD-J71GP21-SX Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CNC MELDASMAGIC Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric GT10-LDR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric VC-X3000 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric DX-ZD6UE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric M32R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Apricot HP DDS DRIVES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC SW1DNC-CCIEF-B Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung