Mitsubishi Electric Q66DA-G Bedienungsanleitung

User’s Manual

(Hardware)

Q66DA-G

Thank you for buying the Mitsubishi general-purpose programmable

controller MELSEC-Q Series.

Channel Isolated

Digital-Analog Converter Module

Prior to use, please read both this manual and detailed manual

thoroughly and familiarize yourself with the product.

MODEL Q-66D/A-G-U-HW

MODEL

CODE 13JY12

IB(NA)-0800362-E(0908)MEE

A-1

SAFETY PRECAUTIONS

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The instructions given in this manual are concerned with this product. For the

safety instructions of the programmable controller system, please read the user's

manual for the CPU module to use

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Note that the " CAUTION" level may lead to a serious consequence according

to the circumstances. Always follow the instructions of both levels because they

are important to personal safety.

Please save this manual to make it accessible when required and always forward

it to the end user.

[Design Precautions]

Indicates that incorrect handling may cause

hazardous conditions, resulting in death or severe

injury.

Indicates that incorrect handling may cause

hazardous conditions, resulting in medium or slight

personal injury or physical damage.

CAUTION

Do not bunch the control wires or communication cables with the main circuit

or power wires, or install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that may cause malfunction.

At power ON/OFF, voltage or current may instantaneously be output from the

output terminal of this module.

In such case, wait until the analog output becomes stable to start controlling

the external device.

DANGER

CAUTION

A-2

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general

specifications given in the User's Manual of the CPU module being used.

Using this programmable controller in an environment outside the range of

the general specifications may cause electric shock, fire, malfunction, and

damage to or deterioration of the product.

While pressing the installation lever located at the bottom of module, insert

the module fixing tab into the fixing hole in the base unit until it stops.

Improper installation may result in malfunction, breakdown or the module

coming loose and dropping. After mounting the module to the base unit

securely hold the module with module fixing bracket.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or

malfunction.

If the screws are tightened too much, it may cause damage to the screw and/

or the module, resulting in fallout, short circuits or malfunction.

Be sure to shut off all phases of the external power supply used by the

system before mounting or removing the module.

Not doing so may cause damage to the module.

Do not directly touch the conductive area or electronic components of the

module.

Doing so may cause malfunction or failure in the module.

A-3

[Wiring Precautions]

CAUTION

Always ground the FG terminal for the programmable controller.

There is a risk of electric shock or malfunction.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or

malfunction.

If the screws are tightened too much, it may cause damage to the screw and/

or the module,resulting in fallout, short circuits or malfunction.

Be careful not to let foreign matters such as sawdust or wire chips get inside

the module.

These may cause fires, failure or malfunction.

The top surface of the module is covered with protective film to prevent

foreign objects such as cable offcuts from entering the module when wiring.

Do not remove this film until the wiring is complete.

Before operating the system, be sure to remove the film to provide adequate

heat ventilation.

A-4

Revisions

* The manual number is given on the bottom right of the cover.

Print Date *Manual Number Revision

Aug., 2006 IB(NA)-0800362-A First edition

Sep., 2006 IB(NA)-0800362-B Correction

Chapter 2, Section 5.3

Oct., 2006 IB(NA)-0800362-C Correction

Chapter 2, Section 5.3, Chapter 6

Feb., 2009 IB(NA)-0800362-D Correction

SAFETY PRECAUTIONS,

ABOUT MANUAL, Compliance with the

EMC and Low Voltage Directives,

Chapter 1, Chapter 2, Chapter 3,

Chapter 4, Section 4.1, Section 5.1, 5.2,

5.3, Chapter 6

Aug., 2009 IB(NA)-0800362-E Correction

Chapter 2, Chapter 3, Chapter 4,

Section 5.3

This manual confers no industrial property rights or any rights of any other kind,

nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be

held responsible for any problems involving industrial property rights which may

occur as a result of using the contents noted in this manual.

A-5

CONTENTS

1. Overview ......................................................................................................... 1

2. Performance Specifications ............................................................................ 2

3. Part Names..................................................................................................... 5

4. Handling Precautions...................................................................................... 6

4.1 Mounting module fixing bracket................................................................ 7

5. Wiring.............................................................................................................. 8

5.1 Wiring precautions.................................................................................... 8

5.2 External wiring .......................................................................................... 9

5.3 Intelligent Function Module Switch Setting............................................. 10

6. External Dimensions ..................................................................................... 11

A-6

ABOUT MANUAL

The following manuals is also related to this product.

In necessary, order it by quoting the details in the table below.

Conformance to the EMC Directive/Low Voltage Directive

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and Low

Voltage Directives when incorporating the Mitsubishi programmable

controller (EMC and Low Voltage Directives compliant) into other

machinery or equipment, refer to Chapter 9 "EMC AND LOW VOLTAGE

DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the programmable controller.

(2) For the product

No additional measures are necessary for the compliance of this

product with the EMC and Low Voltage Directives.

Relevant Manual

Manual name Manual number

(Model code)

Channel Isolated Digital-Analog Converter Module User's

ManualQ66DA-G / GX Configurator-DA

SH-080648ENG

(13JR97)

1. Overview

This manual describes the specifications and the names of the components

and handling for the Q66DA-G channel isolated digital-analog converter

module (hereafter referred to as Q66DA-G) which are used in combination

with the MELSEC-Q series CPU module.

After unpacking, confirm that the following products are enclosed.

The user should arrange for a connector for external wiring since it is not

provided in the package.

(1) Connector types

(2) Pressure-displacement tool

Table 1.1 Packing list

Model code Quantity

Q66DA-G 1

FG terminal L-Shaped metal fitting 1

Table 1.2 Connector types

Type Model name

Soldering type, straight out A6CON1

Crimping type, straight out A6CON2

Soldering type, usable for straight out and diagonal out A6CON4

Table 1.3 Pressure-displacement tool

Type Model name Applicable

wire size Contact

Crimping tool FCN-363T-T05/H AWG24 to 28 FUJITSU COMPONENT LIMITED

2. Performance Specifications

The specifications for the Q66DA-G are shown in the following table. For

general specifications, refer to the operation manual for the CPU module

being used.

Table 2.1 Performance Specifications

Item Specifications

Number of analog outputs 6 points (6 channels)

Digital input 16-bit signed binary (normal resolution mode:-4096 to 4095

high resolution mode: -12288 to 12287, -16384 to 16383)

Using scaling function 16-bit signed binary (-32768 to 32767)

Analog

output

Voltage -12 to 12VDC (External load resistance: 1k to 1M )

Current 0 to 20mADC (External load resistance: 0 to 600 )

0 to 22mADC (External load resistance: refer to *3)

I/O characteristics

maximum resolution

Analog output range

Normal resolution

mode

High resolution

mode

Digital input

value

Maximum

resolution

Digital

input value

Maximum

resolution

Voltage

0 to 5V 0 to 4000 1.25mV 0 to 12000 0.416mV

1 to 5V 1.0mV 0.333mV

1 to 5V

(Extended

mode)

-1000 to

4500 1.0mV -3000 to

13500 0.333mV

-10 to 10V

-4000 to

4000

2.5mV -16000 to

16000 0.625mV

User range

setting 2 0.75mV -12000 to

12000

0.400mV

User range

setting 3 0.375mV 0.210mV

Current

0 to 20mA 0 to 4000 5A 0 to 12000 1.66 A

4 to 20mA 4 A 1.33 A

4 to 20mA

(Extended

mode)

-1000 to

4500 4A -3000 to

13500 1.33 A

User range

setting 1

-4000 to

4000 1.5 A -12000 to

12000 0.95 A

Accuracy

(Accuracy

relative to

maximum

analog

output value)

Reference

accuracy *1 0.1% (Voltage: 10mV, Current: 20 A)

Temperatu

coefficient

80ppm/ (0.008%/ )

Conversion speed 6ms/channel

Absolute

maximum

output

Voltage 13V

Current 23mA

Maximum number of

writes to flash memory MAX. 50,000 times

Output short-circuit

protection Available

Isolation specifications

Specific isolated area Isolation

method

Dielectric

withstand

voltage

Insulation

resistance

Between the output terminal and

programmable controller power supply

Transformer

isolation

500VAC

rms, 1min.

500VDC

10M or

Between analog output channels 1000VAC

rms, 1min.

Between external supply power and

analog output

500VAC

rms, 1min.

Number of I/O occupied

points

16 points

(I/O assignment: Intelligent 16 points)

External wiring

connection system 40-pin connector

Applicable wire size 0.3 mm2or less (for the use of A6CON1,A6CON4),

AWG24 (for the use of A6CON2)

External device

connection connector A6CON1, A6CON2, A6CON4 (Sold separately)

External supply power

24VDC, +20%, -15%

Ripple, spike within 500 mV p-p

Inrush current: 4.8A, within 400 s

0.22A

Internal current

consumption (5 VDC) 0.62A

Weight 0.22kg

Table 2.1 Performance Specifications (Continued)

Item Specifications

Andere Handbücher für Q66DA-G

Inhaltsverzeichnis

Andere Mitsubishi Electric Steuereinheit Handbücher

Mitsubishi Electric

Mitsubishi Electric AJ65BT-D62 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC QJ71PB92D Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric GOT1000 GT1595-XTBA Bedienungs- und Wartungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q2MEM-1MBSN Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PMFY-P-NBMU-ER5 Installations- und Betriebshandbuch

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC-L LD75P Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NL Konfigurationshandbuch

Mitsubishi Electric

Mitsubishi Electric PAC-SV01PW-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric M700VS Series Benutzerhandbuch

Mitsubishi Electric

Mitsubishi Electric QJ71MT91 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PSSxxMC1Fx Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AJ65BT-D62 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric SWL31-ETMC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Trane TE-200A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R RD78G4 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric NZ2GN2S1-32D Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric EMU4-BD1-MB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric EMU4-D65 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX-USB-AW Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung