Mitsubishi Electric AJ65BT64DAV/DAI Bedienungsanleitung

Digital-Analog Converter Module type AJ65BT-

64DAV/DAI User's Manual

Downloaded from ManualsNet.com search engine

A - 1

•SAFETY PRECAUTIONS •

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The instructions given in this manual are concerned with this product. Refer to the user's manual of the

CPU module to use for a description of the programmable controller system safety instructions.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

•Install a safety circuit external to the programmable controller that keeps the entire system safe

even when there are problems with the external power supply or the programmable controller.

Otherwise, trouble could result from erroneous output or erroneous operation.

(1) The status of analog output changes depending on the setting of various functions that

control the analog output. Take sufficient caution when setting for those functions.

For details of analog output status, refer to Section 3.4.5 ”Combinations of various functions”

(2) Normal output may not be obtained due to malfunctions of output elements or the internal

circuits. So build an external monitoring circuit that will monitor any single outputs that could

cause serious trouble.

!CAUTION

•Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100mm(3.94inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

•At power ON/OFF, voltage or current may instantaneously be output from the output terminal of

this module.

In such case, wait until the analog output becomes stable to start controlling the external device.

WARNING

CAUTION

Downloaded from ManualsNet.com search engine

A - 2

[Installation Precautions]

!CAUTION

•Use the module in the environment given in the general specifications of this Manual.

Using this programmable controller in an environment outside the range of the general

specifications could result in electric shock, fire, erroneous operation, and damage to or

deterioration of the product.

•For protection of the switches, do not remove the cushioning material before installation.

•Securely fix the module with a DIN rail or mounting screws. Tighten the screws within the

specified torque range.

Undertightening can cause drop of the screw, short circuit, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

•Do not directly touch the module's conductive parts or electronic components.

Touching the conductive parts could cause an operation failure or give damage to the module.

[Wiring Precautions]

!CAUTION

Shut off the external power suppy for the system in all phases before wiring.

Failure to do so may result in damage to the product.

•Be sure to ground the FG terminals to the protective ground conductor. Not doing so could result

in erroneous operation.

Use applicable solderless terminals and tighten them with the specified torque. If any solderless

spade terminal is used, it may be disconnected when the terminal screw comes loose, resulting

in failure.

•When wiring in the programmable controller, be sure that it is done correctly by checking the

product's rated voltage and the terminal layout.

Connecting a power supply that is different from the rating or incorrectly wiring the product could

result in fire or damage.

•Tighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire, or erroneous operation.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

•Be sure there are no foreign substances such as sawdust or wiring debris inside the module.

Such debris could cause fires, damage, or erroneous operation.

•Do not install the control lines together with the communication cables, or bring them close to

each other. Failure to do so may cause malfunctions due to noise.

•When connecting the communication and power supply cables to the module, always run them

in conduits or clamp them.

Not doing so can damage the module and cables due to loose, moved or accidentally pulled

cables or can cause a malfunction due to a cable connection fault.

Downloaded from ManualsNet.com search engine

A - 3

[Wiring Precautions]

!CAUTION

When disconnecting the communication and power supply cables from the module, do not hold

and pull the cable part.

Disconnect the cables after loosening the screws in the portions connected to the module.

Pulling the cables connected to the module can damage the module and cables or can cause a

malfunction due to a cable connection fault.

[Starting and Maintenance Precautions]

!CAUTION

•Do not touch the terminals while power is on. Doing so may cause malfunctioning.

•Be sure to shut off all phases of the external power supply used by the system before cleaning

or retightening the terminal screws.

Not doing so can cause the module to fail or malfunction.

•Do not disassemble or modify the modules.

Doing so could cause trouble, erroneous operation, injury, or fire.

Do not drop or apply strong shock to the module. Doing so may damage the module.

Be sure to shut off all phases of the external power supply used by the system before mounting

or dismounting the module to or from the panel.

Not doing so could result in damage to the product.

Do not install/remove the terminal block more than 50 times after the first use of the product.

(IEC 61131-2 compliant)

•Before touching the module, always touch grounded metal, etc. to discharge static electricity

from human body.

Failure to do so can cause the module to fail or malfunction.

[Disposal Precautions]

!CAUTION

•When disposing of this product, treat it as industrial waste.

Downloaded from ManualsNet.com search engine

A - 4

•CONDITIONS OF USE FOR THE PRODUCT •

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

yNuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

yRailway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

yAircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

Downloaded from ManualsNet.com search engine

A - 5

REVISIONS

* The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

Jan., 1997 SH(NA)-3615-A First printing

Jun., 2000 SH(NA)-3615-B Addition of Q series types

Chapter 2, Section 3.2, Section 3.4.1, Section 3.6.3, Section 4.2,

Section 6.2

Partial changes

Section 1.1(3), Section 3.1, Section 3.2, Section 3.4.5, Section 4.1,

Section 4.6.2, Section 4.7.2, Section 5.2

Sep., 2004 SH(NA)-3615-C Addition

Conformation to the EMC Directive and Low Voltage Instruction

Correction

SAFETY PRECAUTIONS, About this Manual, Chapter 1, Chapter 2,

Section 3.1, Section 3.2, Section 3.6.4, Section 3.6.5, Section 4.1,

Section 4.4, Section 4.6, Section 4.6.1, Section 4.6.2, Section 4.7.2,

Chapter 5, Section 6.2

Jul., 2005 SH(NA)-3615-D Correction

SAFETY PRECAUTIONS

Oct., 2006 SH(NA)-3615-E Correction

SAFETY PRECAUTIONS, Section 4.2

Dec., 2006 SH(NA)-3615-F Partial correction

Chapter 2(1), Section 3.5.1, Chapter 5

Dec., 2010 SH(NA)-3615-G Addition

CONDITIONS OF USE FOR THE PRODUCT

Correction

SAFETY PRECAUTIONS, Chapter 1, Section 1.1, Chapter 2,

Section 3.1 to Section 3.5, Section 3.5.2, Section 3.6.1, Section 3.6.2,

Section 4.1, Section 4.3, Section 4.6.2, Section 4.7.1, Section 5.1,

Section 5.1, Section 5.2, Section 5.3, Section 5.6, Chapter 6,

Section 6.1, Section 6.2, Appendix 2

Delection

Section 4.6.1

Japanese Manual Version SH-3600-I

This manual does not imply guarantee or implementation right for industrial ownership or implementation

of other rights. Mitsubishi Electric Corporation is not responsible for industrial ownership problems caused

by use of the contents of this manual.

Downloaded from ManualsNet.com search engine

A - 6

Introduction

Thank you for purchasing the Mitsubishi MELSEC-A Series General Purpose Programmable Controller.

Before using the equipment, plese read this manual carefully to develop full familiarity with the functions and

performance of the graphic operation terminal you have purchased, so as to ensure correct use.

Please forward a copy of this manual to the end user.

Table of Contents

1. OVERVIEW 1- 1 to 1- 2

1.1 Features ................................................................................................................................................... 1- 1

2. SYSTEM CONFIGURATION 2- 1 to 2- 2

3. SPECIFICATIONS 3- 1 to 3-14

3.1 General Specification............................................................................................................................... 3- 1

3.2 Performance Specification....................................................................................................................... 3- 2

3.3 I/O Conversion Characteristics................................................................................................................ 3- 4

3.3.1 Offset value and gain value........................................................................................................... 3- 4

3.3.2 I/O conversion characteristics....................................................................................................... 3- 4

3.4 Various Functions to Control the Analog Output .................................................................................... 3- 8

3.4.1 Function to specify hold or clear of the analog output when the programmable controller

CPU is in the STOP status (HOLD/CLEAR setting) .................................................................... 3- 8

3.4.2 Function to specify executing or not executing the D/A conversion processing

(Analog output enable/disable flag).............................................................................................. 3- 8

3.4.3 Function to specify enabling or prohibiting of the analog value external output

(Analog output enable/prohibit setting) ........................................................................................ 3- 8

3.4.4 Offset/gain setting.......................................................................................................................... 3- 8

3.4.5 Combinations of various functions................................................................................................ 3- 8

3.5 I/O Signals to the Master Station............................................................................................................ 3-10

3.5.1 I/O signal list ................................................................................................................................. 3-10

3.5.2 Functions of the I/O signals.......................................................................................................... 3-11

3.6 Remote Register ..................................................................................................................................... 3-12

3.6.1 Allocation of the remote register .................................................................................................. 3-12

3.6.2 Digital value setting area for channels 1 through 4 ..................................................................... 3-13

3.6.3 Analog output enable/prohibit channel ........................................................................................ 3-13

3.6.4 Set value checking code storage area for channels 1 through 4 ............................................... 3-14

3.6.5 Error code..................................................................................................................................... 3-14

Downloaded from ManualsNet.com search engine

A - 7

4. SETUP AND PREPARATION BEFORE OPERATION 4- 1 to 4- 8

4.1 Precautions When Handling .................................................................................................................... 4- 1

4.2 Name of Each Part................................................................................................................................... 4- 2

4.3 Offset/Gain Setting................................................................................................................................... 4- 4

4.4 Station Number Setting............................................................................................................................ 4- 5

4.5 Facing Direction of the Module Installation ............................................................................................. 4- 5

4.6 Data link Cable Wiring ............................................................................................................................. 4- 6

4.6.1 CC-Link dedicated cable connections .......................................................................................... 4- 6

4.7 Wiring........................................................................................................................................................ 4- 7

4.7.1 Precautions when wiring ............................................................................................................... 4- 7

4.7.2 Wiring between the AJ65BT-64DAV/DAI and external devices .................................................. 4- 7

5. PROGRAMMING 5- 1 to 5-18

5.1 Programming Procedure.......................................................................................................................... 5- 1

5.2 Conditions of Program Example.............................................................................................................. 5- 2

5.3 Program Example for Use of the QCPU (Q mode)................................................................................. 5- 4

5.4 Program Example for Use of the QnACPU............................................................................................ 5-10

5.5 Program Example for Use of the ACPU/QCPU (A mode) (dedicated instructions) ............................. 5-12

5.6 Program Example for Use of the ACPU/QCPU (A mode) (FROM/TO instructions) ............................ 5-16

6. TROUBLESHOOTING 6- 1 to 6- 2

6.1 Error Code List ......................................................................................................................................... 6- 1

6.2 Troubleshooting ....................................................................................................................................... 6- 1

6.2.1 When a communication fault occurs between the master station and this module .................... 6- 2

APPENDIX App- 1 to App- 2

Appendix 1 External Dimensions of the AJ65BT-64DAV .........................................................................App- 1

Appendix 2 External Dimensions of the AJ65BT-64DAI...........................................................................App- 2

Downloaded from ManualsNet.com search engine

A - 8

About this Manual

The following are manuals related to this product.

Request for the manuals as needed according to the chart below.

Related Manuals

Manual Name Manual No.

(Type code)

CC-Link System Master/Local Module Type AJ61BT11/A1SJ61BT11 User's Manual

Describes the system configuration, performance specifications, functions, handling, wiring and

troubleshooting of the AJ61BT11 and A1SJ61BT11. (Optionally available)

IB-66721

(13J872)

CC-Link System Master/Local Module Type AJ61QBT11/A1SJ61QBT11 User's Manual

Describes the system configuration, performance specifications, functions, handling, wiring and

troubleshooting of the AJ61QBT11 and A1SJ61QBT11. (Optionally available)

IB-66722

(13J873)

CC-Link System Master/Local Module User's Manual

Describes the system configuration, performance specifications, functions, handling, wiring and

troubleshooting of the QJ61BT11N. (Optionally available)

SH-080394E

(13JR64)

MELSEC-L CC-Link System Master/Local Module User's Manual

Describes the system configuration, Performance specifications, functions, handling, wiring and

troubleshooting of the L26CPU-BT and LJ61BT11. (Optionally available)

SH-080895ENG

(13JZ41)

Compliance with the EMC and Low Voltage Directives

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and Low Voltage

Directives when incorporating the Mitsubishi programmable controller (EMC and

Low Voltage Directives compliant) into other machinery or equipment, refer to

the "EMC AND LOW VOLTAGE DIRECTIVES" chapter of the User's Manual for

the CPU module used.

The CE mark, indicating compliance with the EMC and Low Voltage Directives,

is printed on the rating plate of the programmable controller.

(2) For the product

For the compliance of this product with the EMC and Low Voltage Directives,

refer to the "CC-Link module" section in the "EMC AND LOW VOLTAGE

DIRECTIVES" chapter of the User's Manual for the CPU module used.

Downloaded from ManualsNet.com search engine

Inhaltsverzeichnis

Andere Mitsubishi Electric Controller Handbücher

Mitsubishi Electric

Mitsubishi Electric RJ72GF15-T2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX3U-4AD-PTW-ADP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX3G-2EYT-BD Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric C80 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Central Controller G-50A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MS-T Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAR-U01MEDU Smart ME Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET-G-N1 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-232ADP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSENSOR MELSEC iQ-R MH11H01A0SNA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric QX10 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-IF033B-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric QD62 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX2N-2DA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC L series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2NC-16MT-D/UL Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-Jet MR-JET-G Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q172DCPU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung