Mitsubishi Electric Melsec q26ud(e)hcpu Bedienungsanleitung

QCPU User's Manual

(Hardware Design, Maintenance and Inspection)

-Q00(J)CPU -Q26UD(E)HCPU

-Q01CPU -Q26UDVCPU

-Q02(H)CPU -Q50UDEHCPU

-Q06HCPU -Q100UDEHCPU

-Q12HCPU

-Q25HCPU

-Q02PHCPU

-Q06PHCPU

-Q12PHCPU

-Q25PHCPU

-Q12PRHCPU

-Q25PRHCPU

-Q00U(J)CPU

-Q01UCPU

-Q02UCPU

-Q03UD(E)CPU

-Q03UDVCPU

-Q04UD(E)HCPU

-Q04UDVCPU

-Q06UD(E)HCPU

-Q06UDVCPU

-Q10UD(E)HCPU

-Q13UD(E)HCPU

-Q13UDVCPU

-Q20UD(E)HCPU

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

●Configure safety circuits external to the programmable controller to ensure that the entire system

operates safely even when a fault occurs in the external power supply or the programmable controller.

Failure to do so may result in an accident due to an incorrect output or malfunction.

(1) Configure external safety circuits, such as an emergency stop circuit, protection circuit, and

protective interlock circuit for forward/reverse operation or upper/lower limit positioning.

(2) The programmable controller stops its operation upon detection of the following status, and the

output status of the system will be as shown below.

All outputs may turn on when an error occurs in the part, such as I/O control part, where the CPU

module cannot detect any error. To ensure safety operation in such a case, provide a safety

mechanism or a fail-safe circuit external to the programmable controller. For a fail-safe circuit

example, refer to Page 670, Appendix 9.

(3) Outputs may remain on or off due to a failure of an output module relay or transistor. Configure an

external circuit for monitoring output signals that could cause a serious accident.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Overcurrent or overvoltage protection of

the power supply module is activated.

The CPU module detects an error such as a

watchdog timer error by the self-diagnostic function.

All outputs are turned off All outputs are turned off

All outputs are turned off

All outputs are held or turned off

according to the parameter setting.

Q series module AnS/A series module

[Design Precautions]

WARNING

●In an output module, when a load current exceeding the rated current or an overcurrent caused by a

load short-circuit flows for a long time, it may cause smoke and fire. To prevent this, configure an

external safety circuit, such as a fuse.

●Configure a circuit so that the programmable controller is turned on first and then the external power

supply. If the external power supply is turned on first, an accident may occur due to an incorrect output

or malfunction.

●For the operating status of each station after a communication failure, refer to relevant manuals for the

network. Incorrect output or malfunction due to a communication failure may result in an accident.

●When changing data of the running programmable controller from a peripheral connected to the CPU

module or from a personal computer connected to an intelligent function module, configure an

interlock circuit in the sequence program to ensure that the entire system will always operate safely.

For program modification and operating status change, read relevant manuals carefully and ensure

the safety before operation. Especially, in the case of a control from an external device to a remote

programmable controller, immediate action cannot be taken for a problem on the programmable

controller due to a communication failure. To prevent this, configure an interlock circuit in the

sequence program, and determine corrective actions to be taken between the external device and

CPU module in case of a communication failure.

CAUTION

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●When a device such as a lamp, heater, or solenoid valve is controlled through an output module, a

large current (approximately ten times greater than normal) may flow when the output is turned from

off to on. Take measures such as replacing the module with one having a sufficient current rating.

●After the CPU module is powered on or is reset, the time taken to enter the RUN status varies

depending on the system configuration, parameter settings, and/or program size. Design circuits so

that the entire system will always operate safely, regardless of the time.

[Installation Precautions]

[Wiring Precautions]

CAUTION

●Use the programmable controller in an environment that meets the general specifications in this

manual. Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

●To mount the module, while pressing the module mounting lever in the lower part of the module, fully

insert the module fixing projection(s) into the hole(s) in the base unit and press the module until it

snaps into place. Incorrect mounting may cause malfunction, failure, or drop of the module. When

using the programmable controller in an environment of frequent vibrations, fix the module with a

screw. Tighten the screw within the specified torque range. Undertightening can cause drop of the

screw, short circuit or malfunction. Overtightening can damage the screw and/or module, resulting in

drop, short circuit, or malfunction.

●When using an extension cable, connect it to the extension cable connector of the base unit securely.

Check the connection for looseness. Poor contact may cause incorrect input or output.

●When using a memory card, fully insert it into the memory card slot. Check that it is inserted

completely. Poor contact may cause malfunction.

●When using an SD memory card, fully insert it into the SD memory card slot. Check that it is inserted

completely. Poor contact may cause malfunction.

●When using an extended SRAM cassette, fully insert it into the connector for cassette connection of

the CPU module. Close the cassette cover after inserting to avoid looseness of the extended SRAM

cassette. Poor contact may cause malfunction.

●Shut off the external power supply (all phases) used in the system before mounting or removing the

module. Failure to do so may result in damage to the product. A module can be replaced online (while

power is on) on any MELSECNET/H remote I/O station or in the system where a CPU module

supporting the online module change function is used. Note that there are restrictions on the modules

that can be replaced online, and each module has its predetermined replacement procedure. For

details, refer to this manual and in the manual for the corresponding module.

●Do not directly touch any conductive part of the module, the memory card, the SD memory card, or

the extended SRAM cassette. Doing so can cause malfunction or failure of the module.

●When using a Motion CPU module and modules designed for motion control, check that the

combinations of these modules are correct before applying power. The modules may be damaged if

the combination is incorrect. For details, refer to the user's manual for the Motion CPU module.

WARNING

●Shut off the external power supply (all phases) used in the system before wiring. Failure to do so may

result in electric shock or damage to the product.

●After installation and wiring, attach the included terminal cover to the module before turning it on for

operation. Failure to do so may result in electric shock.

[Wiring Precautions]

CAUTION

●Individually ground the FG and LG terminals of the programmable controller with a ground resistance

of 100 or less. Failure to do so may result in electric shock or malfunction.

●Use applicable solderless terminals and tighten them within the specified torque range. If any spade

solderless terminal is used, it may be disconnected when the terminal screw comes loose, resulting in

failure.

●Check the rated voltage and terminal layout before wiring to the module, and connect the cables

correctly. Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire

or failure.

●Connectors for external connection must be crimped or pressed with the tool specified by the

manufacturer, or must be correctly soldered. Incomplete connections could result in short circuit, fire,

or malfunction.

●Install the connector to the module securely. Poor contact may cause malfunction.

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●Place the wires or cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be

pulled, resulting in damage to the module or cables or malfunction due to poor connection.

●Connect the cable correctly after confirming the interface type to be connected. Connecting to the

wrong interface or incorrect wiring can result in a failure of the module or external devices.

●Tighten the terminal screw within the specified torque range. Undertightening can cause short circuit,

fire, or malfunction. Overtightening can damage the screw and/or module, resulting in drop, short

circuit, or malfunction.

●Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter can

cause a fire, failure, or malfunction.

●A protective film is attached to the top of the module to prevent foreign matter, such as wire chips,

from entering the module during wiring. Do not remove the film during wiring. Remove it for heat

dissipation before system operation.

●Do not pull the cable section of a cable for disconnection. When disconnecting a cable with a

connector, hold the connector and pull it. When disconnecting a cable on a terminal block, loosen the

terminal screw before disconnection. Pulling the connected cable can result in malfunction or damage

of the module or the cable.

●Mitsubishi Electric programmable controllers must be installed in control panels. Connect the main

power supply to the power supply module in the control panel through a relay terminal block. Wiring

and replacement of a power supply module must be performed by maintenance personnel who is

familiar with protection against electric shock. (For wiring methods, refer to Page 103, Section 4.8.1.)

[Startup and Maintenance Precautions]

WARNING

●Do not touch any terminal while power is on. Doing so will cause electric shock.

●Correctly connect the battery connector. Do not charge, disassemble, heat, short-circuit, solder, or

throw the battery into the fire, or apply liquid or a strong shock to the battery. Doing so will cause the

battery to produce heat, explode, ignite, or liquid spill, resulting in injury and fire.

●Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws, connector screws, or module fixing screws. Failure to do so may

result in electric shock or cause the module to fail or malfunction.

CAUTION

●Before performing online operations (especially, program modification, forced output, and operation

status change) for the running CPU module from the peripheral connected, read relevant manuals

carefully and ensure the safety. Improper operation may damage machines or cause accidents.

●Do not disassemble or modify the modules. Doing so may cause failure, malfunction, injury, or a fire.

●Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone

System) more than 25cm away in all directions from the programmable controller. Failure to do so

may cause malfunction.

●Shut off the external power supply (all phases) used in the system before mounting or removing the

module. Failure to do so may cause the module to fail or malfunction. A module can be replaced

online (while power is on) on any MELSECNET/H remote I/O station or in the system where a CPU

module supporting the online module change function is used. Note that there are restrictions on the

modules that can be replaced online, and each module has its predetermined replacement procedure.

For details, refer to this manual and the manual for the corresponding module.

●After the first use of the product, do not mount/remove the module to/from the base unit, the extended

SRAM cassette to/from the CPU module, or the terminal block to/from the module more than 50 times

(IEC 61131-2 compliant) respectively. Exceeding the limit of 50 times may cause malfunction.

●After the first use of the product, do not mount/remove the SD memory card more than 500 times.

Exceeding the limit of 500 times may cause malfunction.

●Do not drop or apply shock to the battery to be installed in the module. Doing so may damage the

battery, causing the battery fluid to leak inside the battery. If the battery is dropped or any shock is

applied to it, dispose of it without using.

●Before handling the module, touch a grounded metal object to discharge the static electricity from the

human body. Failure to do so may cause the module to fail or malfunction.

[Disposal Precautions]

[Transportation Precautions]

CAUTION

●When disposing of this product, treat it as industrial waste. When disposing of batteries, separate

them from other wastes according to the local regulations. (For details of the Battery Directive in EU

countries, refer to Page 678, Appendix 12.)

CAUTION

●When transporting lithium batteries, follow the transportation regulations. (For details of the regulated

models, refer to Page 677, Appendix 11.)

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major

or serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of

the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT

LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,

WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR

LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR

USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,

OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any

other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of

a special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as

Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,

Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a

significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT

is limited only for the specific applications agreed to by Mitsubishi and provided further that no

special quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

INTRODUCTION

This manual provides hardware specifications, maintenance and inspection of the system, and troubleshooting of the CPU

modules, power supply modules, and base units required for operating the Q series programmable controllers.

Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the

functions and performance of the Q series programmable controller to handle the product correctly.

When applying the program examples introduced in this manual to the actual system, ensure the applicability and confirm that

it will not cause system control problems.

Relevant CPU module

Precautions when using the Q series CPU module for the first time

Memory must be formatted using a programming tool before first use of the CPU module.

For details of memory formatting, refer to the following.

Operating manual for the programming tool used

Precautions for batteries

(1) When resuming operation with the CPU module which has been stored without battery:

The CPU module memory must be formatted using a programming tool. ( Page 264, Section 13.4)

Remark

This manual does not describe the functions of the CPU module.

For the functions, refer to the following.

Manuals for the CPU module used. (Function Explanation, Program Fundamentals)

For multiple CPU systems, refer to the following.

QCPU User's Manual (Multiple CPU System)

For redundant systems, refer to the following.

QnPRHCPU User's Manual (Redundant System)

CPU module Model

Basic model QCPU Q00(J)CPU, Q01CPU

High Performance model QCPU Q02(H)CPU, Q06HCPU, Q12HCPU, Q25HCPU

Process CPU Q02PHCPU, Q06PHCPU, Q12PHCPU, Q25PHCPU

Redundant CPU Q12PRHCPU, Q25PRHCPU

Universal model QCPU

Q00U(J)CPU, Q01UCPU, Q02UCPU, Q03UD(E)CPU, Q03UDVCPU,

Q04UD(E)HCPU, Q04UDVCPU, Q06UD(E)HCPU, Q06UDVCPU,

Q10UD(E)HCPU, Q13UD(E)HCPU, Q13UDVCPU, Q20UD(E)HCPU,

Q26UD(E)HCPU, Q26UDVCPU, Q50UDEHCPU, Q100UDEHCPU

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Controller Handbücher

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MEsoftstart/I01 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-IF033B-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC LJ72GF15-T2-U-HW Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC L-Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AJ65BT-D75P2-S3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YG60MCA Service-Handbuch

Mitsubishi Electric

Mitsubishi Electric Q173CPU Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CR800-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melsec-F FX2NC Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo HF-KN Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Handbuch

Mitsubishi Electric

Mitsubishi Electric MELSEC-A/QnA Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric SV13/22 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric A1SJ71PB96F Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric VAR-6A Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

Mitsubishi Electric melsec q26ud(e)hcpu Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken