Mitsubishi Electric Jet Towel JT-MC106G-W-NA Bedienungsanleitung

EnglishFrançais

−NA -1 −

MODEL

JT-MC106G-W-NA

Unit color -W（White）

Hand dryer

875HJ9901

Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.

Installation shall comply with local requirements and Electrical Code and be performed by the dealer or a qualiﬁed

professional in accordance to local jurisdiction.

The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.

INDEX

Safety Precautions 2

Pre-installation checks 3

■Checking the installation environment 3

■Checking the unit, accessories

and items required for installation 3

Names of parts and external dimensions 4

Installation conditions 5

■Required space for installation 5

■Suitable walls 5

■Making the unit easier to use 5

Installation method 6 – 11

Test Run 12

Initial setting checks 13

■How to open/close the front cover 13

Precautions for when opening/closing

the front cover 13

■Turning the heater on 14

■Turning the sensor off before maintenance 15

INSTALLATION MANUAL

Location of Name plate indicating

Model name and Electrical ratings

Input Power: 120 Vac Single-phase

Indoor use only

For Dealers and Installers

English

−NA -2 −

Safety Precautions

󱾀The dangers arising from improper handling and the extents of the dangers are classified and explained as

shown below.

Prohibited

󱾀Do not install in locations where they

may be leakages of combustible gas.

This may cause fires.

󱾀Do not install in locations where salt

damage may occur or where corrosive,

neutral or reductive gases are present.

This may cause malfunctions.

󱾀Do not scratch, damage, process,

excessively bend, pull, twist or bundle

the power cable.

Please also refrain from placing heavy

objects onto it or trapping it.

Failure to do so may damage the power

cable, causing fires or electric shocks. Important !

instructions.

󱾀Wiring work shall be done by a

licensed electrician in accordance with

electrical and building codes.

Incorrect wiring work may cause electric

shocks or fires.

󱾀Use single-phase 120 Vac power.

Using the incorrect power supply

may cause fires, electric shocks or

malfunctions.

󱾀Use delicated wiring for the power

source.

Using this unit with other devices on the

same branch circuit may cause abnormal

heat, which may cause fires.

󱾀The unit shall be installed in

accordance with appropriate wiring

regulations in accordance to local

jurisdiction.

󱾀A means for disconnection must be

incorporated in the fixed wiring in

accordance with wiring rules.

󱾀The disconnecting device shall be of

all-pole disconnection.

󱾀This hand dryer must have its own

delicated branch circuit using

AWG #12 or #14 copper wire.

Do not

disassemble

󱾀Do not attempt any disassembly or

modification of the unit that is not

expressly stated in this manual.

Doing so may result in fires, electric

shocks or injuries.

Do not use

in the baths/

shower room.

󱾀Do not use in a hot location such as a

shower room, where condensation may

form on the unit or where water may

splash directly onto the unit.

This may cause electric shocks or

malfunctions.

Warning The following may lead to death or serious

personal injury if handled incorrectly.

Prohibited

󱾀Do not install when the unit (power

cable) is energized.

Doing so may result in electric shocks. Important !

instructions.

󱾀Install securely in a location strong

enough to support the weight of the

unit.

Injuries may be caused if the unit falls off

the wall.

󱾀Wear gloves when installing the unit.

Not doing so may result in injuries.

Caution The following may lead to injuries or damage to

property if the unit is handled incorrectly.

English

−NA -3 −

Pre-installation checks

󱾀Input Power: 120 Vac Single-phase is used.

Using the incorrect power supply may cause ﬁres, electric shocks or malfunctions.

■Checking the installation environment

Do not install the unit in the following types of locations.

(This may cause malfunctions.)

󱾀 Outdoors 󱾀 Locations where the temperature could be lower than 32F (0C).

󱾀

Locations where there is a lot of dust.

󱾀

Locations where the temperature could be higher than 104F (40C).

󱾀 Locations where there is a lot of condensation. 󱾀 Locations where salt damage may occur.

󱾀 Locations where the unit is in direct or strong sunlight (may cause the sensor to malfunction).

󱾀 In vehicles (including ships and airplanes)

󱾀 Locations where corrosive, neutral or reductive gasses are present.

(This may shorten the working life of the unit and/or cause malfunctions.)

󱾀 Near food or tableware 󱾀 Locations where the unit may come into direct contact with water.

󱾀 Kitchens

(Where there is a risk of water splashing.)

󱾀 Rooms that have a sterilization basin, swimming pools and baths.

■Checking the unit, accessories and items required for installation

※Shaded areas in the ﬁgure indicate antibacterial material (excluding outlet nozzle areas).

Main unit

Air ﬁlter

Open

Lid

Drain tank

How to open/close the front cover

(refer to Page 13)

Mounting screws 7

(5×30 Type 1 tapping screws)

Installation panel 1

Cord clip mounting screw

(4 ×14) 1

Cord clip 1

Screwdriver Pen

Screw anchor 7 Wall reinforcement

※To mark position to insert metal

screw plugs in the wall.

※Use on concrete walls ※Reinforces walls made of

materials other than concrete.

■Prepare if required

※Not needed if the internal wiring is

complete.

Single wire for internal wiring

(Cable core: between 2.0mm² and 3.0mm²)

Warning

Front cover

Unit

Recommended tools and hardware to be used for installation

Accessories

English

−NA -4 −

67/16"

(163)

71/2"(190)

187/8"(480)

97/8"(251.5)

"(138.5)

515/16"(150)

87/16"(215)

97/8"(250)

"315/16

(100)

"11/4

(31)

(52)

"19/16

(40)

"611/16

(170)

1/8(28)

1/16

(2)

Names of parts and external dimensions

■Main unit

■Front

Installation panel Air ﬁlter

Power

light

Drain tank

Unit (in. (mm))

󱾀Conﬁrm the details in the "Installation conditions" (Page 5).

Power light

Front

cover

Nozzle

Sensor

Hand

drying

area

Lid

Drain tank

Water

receiver

area

Inside the front cover

Air ﬁlter Setting switches

Front cover Open

Sensor light

Sensor

switch

Heater light

Heater

switch

Power light

■Rear

Power cord hole

Main unit

󱾀Open the front cover while referring to "How to open/close the front cover" (Page 13).

󱾀Please refer to "Turning the heater on" (Page 14) while turning the heater on/off.

󱾀Please refer to "Turning the sensor off before maintenance" (Page 15) while turning the sensor on/off.

NOTE

English

−NA -5 −

"2 1/16

(52)

"51/2

(140)

"55/8

(143)

"19/16

(40)

"5 15/16

(150)

97/8"(251.5)

231/16"(585)

"(138.5)

7/8(22)

Installation conditions

■Required space for installation

Caution Be sure to secure at least the

distances listed in the right-

hand table from walls, ﬂammable

(combustible) materials and so

on.

■Suitable walls

󱾀When installing on a wall, select a wall with a ﬂat

and even surface.

󱾀When installing on a concrete wall, use commercially

available metal screw plugs.

󱾀Reinforce any walls made with materials other than

concrete before installation.

■Making the unit easier to use

󱾀Refer to the "Installation position guide" and

"Installation diagram" while installing the unit in order

to make it easier to use.

If it is installed at a low position, it may become wet

when the sink is being washed. If water enters the

unit, it may cause damage or cause the acoustic

materials to absorb water and allow bacteria to grow.

󱾀Do not install the main unit in locations such as

those near mirrors or walls. This may lead to water

drops ﬂying to undesirable areas during the drying

of the hands.

󱾀Do not install the main unit in locations such as

those near food or eating utensils. This may lead to

water drops ﬂying to undesirable areas during the

drying of the hands.

󱾀Avoid locations where people or doors might bump

into the unit.

※When installed

above a sink

Rear side Top side

Left side

Main

unit

Right

side

Bottom side

Unit (in. (mm))

Location Isolation

distance

Above 5 15/16" (150)

Left 3 15/16" (100)

Right 5 15/16" (150)

Front Open

Below 2" (50)

■Installation position guide

Installation

panel

Guide from ﬂoor to

installation position

Men : 51

3/8" (1305)

Women : 47

7/16" (1205)

When there is a sink,

585 from the top of

the sink should be the

approximate distance.

Unit (in. (mm))

■Installation diagram

Recommended A measurements during installation

Unit (in. (mm))

Space below the unit A

When there are no objects below Men 51 3/8" (1305)

Women 47 7/16" (1205)

When there is an object such as a sink 23 1/16" (585)

Unit (in. (mm))

Electrical

Conduit/Tubing

1/2"

Connector

The top

surface

such as

washstands

FLOOR

English

−NA -6 −

"2 1/16

(52)

"51/2

(140)

"55/8

(143)

"19/16

(40)

"5 15/16

(150)

97/8"(251.5)

"(138.5)

7/8(22)

4 15/16"(125)

1/2"(12)

Installation method

For conﬁrmation

□Input Power: 120 Vac Single-phase power is being used (using the incorrect power supply may cause ﬁres,

electric shocks or malfunctions).

□The ground fault circuit interrupter is attached (not attaching a ground fault circuit interrupter may result in

electric shocks).

□A single wire (cable core: 2.0mm² or 3.0mm²) is being used for the power cable.

Warning

󱾀

This hand dryer must have its own independent branch circuit using

AWG #12 or #14 copper wire.

󱾀

Use 120 Vac power.

Using the incorrect power supply may cause ﬁres, fumes, electric shocks

or malfunctions.

Caution

󱾀

Do not install when the unit (power

cable) is electriﬁed.

Doing so may result in electric

shocks.

1. Conﬁrm that the severing of wires

during ﬁxed wiring work is in

accordance with wiring regulations.

󱾀Follow the illustration on the right for the internal

wiring.

󱾀The power cable forces out the main unit and

does not allow proper installation if the conduit

box is not used.

Wire it to the terminal block. (No polarity)

2. Remove 9/16"(15mm) of wire sheath from

the end.

3. Position the installation panel on wall

so that the back electrical inlet can be

connected to the pre-installed electrical

conduit/tubing with the 1/2" (16mm)

connector.

Unit (in. (mm))

Terminal block

Power cord hole (rear)

Unit external shape

Mounting

hole position

below the

unit

■Single wire

Electrical

Conduit/Tubing

1/2"

Connector

1/2" Connector

Tighten to connect the

installation panel and

electrical conduit/tubing.

Back Electrical Inlet

9/16"(1004.5)

- 43

1/2"(1104.5)

min.

13/16"(173) min.

7/8"(327)

English

−NA -7 −

"2 1/16

(52)

"51/2

(140)

"55/8

(143)

"19/16

(40)

"5 15/16

(150)

97/8"(251.5)

231/16"(585)

"(138.5)

7/8(22)

Installation method - continuation

Fix the installation panel onto the wall

with 5 accessory mounting screws

(5×30).

󱾀The "Installation position guide" illustrated on

the right is recommended.

󱾀When installing on a wall, select a wall with a

ﬂat and even surface.

󱾀When installing on a concrete wall, use

commercially available metal screw plugs.

󱾀Reinforce any walls made with materials

other than concrete before installation.

※When installing above a sink, the

recommended B measurement is 23 1/16"

(585mm) above the sink.

Installation panel

Mounting screws (5×30)

(Accessories)

■Installation position guide

Recommended A measurements during installation

Unit (in. (mm))

Space below the unit A

When there are no objects below Men 51 3/8" (1305)

Women 47 7/16" (1205)

When there is an object such as a sink 23 1/16" (585)

Unit (in. (mm))

Electrical

Conduit/Tubing

1/2"

Connector

The top

surface

such as

washstands

FLOOR

English

−NA -8 −

Installation method - continuation

1. Remove the drain tank. Drain tank

5. Remove the terminal block cover

mounting screw (1), and remove the

terminal block cover.

※Be careful not to lose the cord bushing.

Base

Cord bushing

Terminal block cover

Terminal

block cover

mounting

screw

2. Open the front cover and remove the

air ﬁlter.

※Refer to "How to open/close the front cover"

(Page 13).

Air ﬁlter Air ﬁlter

Open Main unit

panel

Pull the tab and open the front

cover.

Tab

3. Remove the main unit panel

mounting screw (1).

4. Unlock the upper tabs (2 locations)

of the main unit panel, and remove

the main unit panel from the base.

Main unit panel

mounting screw

Main

unit panel

Base

Main unit panel

Tab

Base

Pull the tab and open the front

cover. Ta b

Front cover

1. Push the power cable for exclusive

wiring through the power cord hole

at the rear of the base.

2. Engage the base with the 2 hooks on

the installation panel.

3. Check that the power cable is not

trapped behind the base. Base

Ground wire

Power cord hole

Power cable

Ground wire

Installation

panel

Panel hooks

(2 locations)

English

−NA -9 −

Installation method - continuation

4 15/16"(125)

1/2"(12)

Warning

󱾀Input Power: 120 Vac Single-phase is used.

Using the incorrect power supply may cause ﬁres, electric shocks

or malfunctions.

Caution

󱾀Make sure that the main unit

does not fall as the base is not

attached to the wall with screws.

Injuries may be caused if the unit

falls off the wall.

Wire the power cable to the terminal block.

(No polarity)

1. Remove 1/2"(12mm) (single wire).

Fix the power cable to the terminal block.

󱾀When stranded wire is used for the power

cable, attach an insulated ring tongue terminal

using an appropriate tool.

󱾀Proper torque is 1.5N·m

3. Check that the power cable is

securely ﬁxed to the terminal block.

4. Fix the ground wire to the terminal

block.

󱾀Proper torque is 1.5N·m

5. Check that the ground wire is

securely ﬁxed to the terminal block.

6. Use the cord clip mounting screw

hole to ﬁx the power cable with the

accessory cord clip and mounting

screw (4 ×14).

󱾀Proper torque is 1.5N·m

󱾀Fix it where the external wire sheath of the

power cable is when it is fixed in the cord clip

mounting position.

󱾀Do the wiring so that the power cable goes

through the right side of the circuit case.

The main unit panel may not be able to be

attached if it is above the circuit case.

Terminal block

Base

Circuit case Power cable

Power cable

Screw

Power

cable

Power

cable

Ground wire

Ground wire of

installation panel

Ground wire of

installation panel

Ground

wire

Base

Circuit case

■Single wire

Unit (in. (mm))

Base Cord clip

mounting

screw hole

Circuit case

Power cable Cord clip

mounting screw

(4×14)

(Accessory)

Cord clip

(Accessory)

English

−NA -10 −

Installation method - continuation

1. Place the power cable through the

cord bushing and reattach it to the

circuit case with the terminal block

cover mounting screw.

2. Check that the power cable and wires

are not pinched anywhere.

1. Insert the "Motor lead wire" into the

gap of ribs on the Base.

Caution

󱾀Check to see that the "Moter lead wire" is

fitted to the gap of ribs.

2. Insert the tabs (2 locations) of the

main unit panel into the locks of the

base hooks and ﬁx it with screw (1).

󱾀The screw is inside the front cover.

3. Check that the 2 hooks on the main

unit panel are hooked in the base.

4. Gently press the unit against the wall,

and ﬁx it in place using 2 accessory

mounting screws (5×30).

󱾀When installing on a concrete wall, use

commercially available metal screw plugs with

the procedures below before fixing the front

cover onto the base.

①Temporarily place the main panel on the

base.

②Mark the position of the hole in the wall

through the mounting screw hole with a

pen.

③Remove the main unit panel and insert

commercially available metal screw plugs

into the marked locations of the wall.

󱾀Reinforce any walls made with materials other

than concrete before installation.

Base

Terminal block

cover mounting

screw

Terminal

block cover

Cord

bushing

Main unit panel

Tab

Base

Main unit panel

Front cover

Main unit panel

mounting screw

Main unit

panel

Installation

hole

Mounting screws

(5×30)

(Accessories)

Plugging marks

on the wall

Plug positioning

Mounting screws

(5×30)

(Accessories)

Mark the wall in

2 places

Pull the tab for opening the

front cover. Tab

Andere Handbücher für Jet Towel JT-MC106G-W-NA

Inhaltsverzeichnis

Sprachen:

Andere Mitsubishi Electric Trockner Handbücher

Mitsubishi Electric

Mitsubishi Electric JT-SB216JSH2-W-NE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB216DS-W-AUS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S1AP-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-MC206GS-W-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB216ESH-W-CE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB216ESH-W-CE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB116JH-G-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB216JSH-W-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB116JH-G-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S2AP-W-NE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S1AP-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S1AP-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB116JH2-S-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-MC206GS-W-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S1AP-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-MC106G-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric T-SB116EH-W-CA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB216JSH-W-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB116JH-G-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB116EH-W-CA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-SB116JH2-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-MC106G-W-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Jet Towel JT-SB116JH-G-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric JT-S2AP-S-NE Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung