Mitsubishi Electric PAC-IH03V2-E Bedienungsanleitung
CYLINDER UNIT OPTIONAL PARTS
IMMERSION HEATER (1Ph 3kW)
PAC-IH03V2-E
WARNING
●
●
●
●
●
INSTALLATION MANUAL
If the cylinder has already been connected to the power supply ensure circuit breaker is off before carrying out electrical
work.
If the immersion heater is installed incorrectly or modified after installation by the user, water leakage, electric shock or
fire may result.
All electrical work should be performed by a qualified technician according to local regulations and the instructions given
in this manual.
The immersion heater must be powered by a dedicated power supply and the correct voltage and correctly sized circuit
breakers must be used.
Connections must be made securely and without tension on the terminals.
The included component parts of the PAC-IH03V2-E IMMERSION HEATER (1Ph 3kW) shall be used only for the
purposes indicated in the installation manual.
● Before starting installation, read the following description together with the installation manual included with the cylinder unit.
● Please read carefully and observe fully the following safety precautions.
Precaution that must be observed to prevent injuries or death.
WARNING
After installation carry out a test run to ensure correct operation, then explain operation method and safety precautions to the
end user.
Tell your customers to keep this installation manual together with the operation manual, and when they give or sell this
machine to any other person include this installation manual and operation manual with it.
●
Optional parts
D-25
Immersion Heater
3Optional parts
Item
Immersion heater
Thermostat (High limit thermal cut-out)
Tab cover
Earth leakage breaker
Screw (4×25)
Relay
Screw (4×16)
Label (for Earth leakage breaker)
Label (for Relay)
Lead wire with connector
Lead wire (Red, 130mm)
Lead wire (Blue, 130mm)
Lead wire (Red, 1500mm)
Lead wire (Blue, 1500mm)
Water-proof cover
Water-proof seal (3x35x25)
Water-proof seal (3x40x25)
Band
Tool
Installation manual
Fastener
Spec name plate
Piece
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
Contents
Optional parts
D-26
Immersion Heater
3Optional parts
A2
A1
Carefully remove front panel
by disconnecting the control
cable from beneath the unit’s
main control box.
The blanking plate and gasket
can be removed using a narrow
flat bladed screwdriver.
Dispose
Check before starting installation
that no water is in the tank.
Diagonally locate the thermostat pockets on upper
right and bottom left with terminals on the upper left
and bottom right sides as shown.
Secure tightly with the nut to prevent water leakage.
(Recommended torque = 10 N•m)
Reinstate plastic tab cover over
the connectors then insert the
thermostat rod into the upper
right hand pocket.
The terminals on the white
plastic head should be positioned
at the bottom as shown.
Assemble and securely.
Screw positions
Place the terminal
blocks so that the
orientations of the
labels are correct.
Align the centre lines 4
and 8as shown.
Align the centre
lines 6and 9
as shown.
Connector CNIH
1 2 3
4 5 6
7 8 9
Optional parts
D-27
Immersion Heater
3Optional parts
Run the lead wire through
the slit on the water-proof
cover provided and seal
each terminal screw.
Place the band on the joint surface of the
DHW tank.
Secure the water-proof cover around the
cylinder boss using the band provided.
DIP Switch
1-4 OFF→ON
(without immersion heater
→with immersion heater)
Fix it to the
other wires.
The fixing position of lead wire using bands
and/or fasteners.
Fix it to the
pipe covers.
SPEC
NAME
PLATE
Carefully reinstate control cable
connection before reinstating
and securing the front panel.
Do not insert the lead wires 3and 4into the
opening that the main controller wires or the
wireless receiver wires use.
3
4
10 11 12
13 14 15
16 17 18
For details about wiring to power
supply and circuit breaker, refer to
the installation manual and wiring
diagram for the cylinder unit.
Fill tank with water and ensure that
no water leaks around the periphery
of the immersion heater.
Optional parts
D-28
Immersion Heater
3Optional parts
Andere Mitsubishi Electric Heizung Handbücher
Mitsubishi Electric
Mitsubishi Electric Thermoscreens VRF HP Leitfaden
Mitsubishi Electric
Mitsubishi Electric CITY-MULTI PAC-PH01EHY-E Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric PAC-IH03V-E Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric GK-2509YS2-CE Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric PAC-646BH-E Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung