Mitsubishi Electric MELDAS 600 Series Bedienungsanleitung

MITSUBISHI CNC

MELD/IS

600

Series

MAINTENANCE TOOL

INSTRUCTION MANUAL

BNP-63988-001* (ENq

ADVANCED AND EVER AOVANCING

Mll’SlJBlSHl ELECTRIC

Revision History

Sub-No.

Date of revision

June 1999

Revision details

First edition created.

CONTENTS

1. Outline .........................................................................................................................................

2. Work Environment ..............................................................................................................................

2.1 Items to prepare.. ........................................................................................................................

2.2 Setting the HR98x caxx$te .......................................................................................................

2.3 Mounting the maintenance tool cassette.. ..................................................................................

3. Starting and Ending the M6 Maintenance Tool ..............................................................................

3.1 Starting the tool ...........................................................................................................................

3.2 Ending the tool.............................................................................................................................

3.3 Main menu.. .................................................................................................................................

4. Memory Back Up .................................................................................................................................

4.1 Preparation ..................................................................................................................................

4.2 Operating procedure ...................................................................................................................

4.3 Explanation of commands ..........................................................................................................

4.4 Emr messages.. .........................................................................................................................

5. Serial Number and NC Typk, Unit type Set .....................................................................................

5.1 Preparation ..................................................................................................................................

5.2 Operating procedure ...................................................................................................................

6. Servo Spindle FNV Down Load.. ........................................................................................................

6.1 Preparation ..................................................................................................................................

6.2 Starting the tool ...................................................................................... .....................................

6.3 Operating proce&re in the normal mode.. .................................................................................

6.3.1 Initial screen .....................................................................................................................

6.3.2 Operation display.. ...........................................................................................................

6.3.3 Error information ..............................................................................................................

6.4 Operating procedure in the automatic firmware download mode .............................................

6.4.1 Operation proc&,re.. ......................................................................................................

6.4.2 List of error Nos ...............................................................................................................

6.5 Internal mnfigur&on of the M500 Maintenance Tool CaSSetk.. ...............................................

7. Command Line Mode ..........................................................................................................................

7.1 Outline ........................................................................................................................................

7.2 Memory map ....................................... .......................................................................................

7.3 l& of cammlds.. ......................................................................................................................

7.4 &mmand format.. ......................................................................................................................

7.5 Explanation of comma& ..........................................................................................................

7.5.1 End command line tool.. ..................................................................................................

7.5.2 Display help.. ....................................................................................................................

7.5.3 Display memory information ............................................................................................

7.5.4 Display memory.. .............................................................................................................

7.5.5 Modify memory.. ..............................................................................................................

7.5.6 Write FROM.. ...................................................................................................................

7.5.7 Erase FROM ...................................................................................................................

7.5.8 copy memory ..................................................................................................................

7.5.9 W&e memory.. ................................................................................................................

7.510 Clear memory.. ................................................................................................................

7.5.11 Compare memory.. ..........................................................................................................

7.5.12 meate a wpy of the M6 Maintenance Tool ....................................................................

8. Appendix 1 HyperTermlnal Starting Procedure ............................................................................

18 .

:. >

1. Outline

The M6 Maintenance Tool is used when performing maintenance on a CNC shipped to the machine

maker, end user, etc. The tool has the following functions.

1) Memory Backup function

2) Serial number, CNC type and unit type setting function

3) Servo, spindle F/w download function

4) Memory backup by command line function

The M6 Maintenance Tool is provided as an HR98x cassette, and is used mounted on C-BUS #2 of the

CNC. The M6 Maintenance Tool is operated usina a VDS. Because of this, a VDS and cable that can

be connected to the CNC are required.

[Supplement]

*l : System, boot ROM upgrades

. The system and boot ROM are not upgraded by the maintenance tool. These are upgraded

using cassettes specially dedicated for upgrading.

*2 :’ PLC (ladder) upgrades

PLc’s are upgraded following the appropriate method for each model.

-l-

2. Work Environment

Connect the VDS to serial port 1

on the CNC

side of the actual device. If using a notebook personal

computer with a Windows 95 (Windows 98) system as the VDS, the standard “HyperTerminal” program

can be used. Refer to the Appendix for details on how to start “HyperTerminal”.

Serial

cable

2.1 Items to prepare

M6 Maintenance Tool (HR98x cassette). *

VDS or notebook personal computer that can be used as a VDS.

DSUB 25pin serial cable (CNC side connector). Note that because the operation board differs

according to the model, the correct cable must be confirmed.

Accuracy driver (required for changing the rotary switch).

2.2 Setting the HR98x castiette

The M6 Maintenance Tool is provided as an HR98x cassette. Set the HR98x as follows.

HR98x card ,Expa”s’l C-BUS

Mounton

C-BUS #2 of the HR113 card

Setting pin : Leave open (no setting pin).

Rotary switch 1 : Use for automatic servo download. Normally set to 0.

Rotary switch 2 : Not used. Set to 0.

-3-

2.3 Mounting the maintenance tool cassette

The following shows the cassette mounting location.

1) The maintenance tool (HR98x cassette) is mounted on C-BUS #2 of the HR113 or HRl 11 card.

2) Depending on the functions to be used, cassettes for memory backup or cassettes for copying

FROM cassettes may be mounted in addition to the maintenance tool (HR98x cassette). Mount the

cassettes using the following drawing as a reference.

(Note) Always mount/remove cassettes with the CNC power OFF

Back view of

unit

ir-segment LED \ CN6 reset

Rotary switch

I Memory cassette I

Espansion C-BUS

(EXTC-BUS)

Roteryswfich 1

Rotary switch 2

Mount the HR96x card on C-BUS #2

Memorycessette

..:

3. Starting and Ending the M6 Maintenance Tool

3.1 Starting the tool

Two types of start modes can be selected by setting the rotary switch on top of the main CPU

(HFil KM-Ml 11) (The rotary switch always returns to its original setting after the operation is completed,

so check the current setting to be sure it is correct.)

CPU rotary

switch Start mode Outline

Set the main CPU rotary switch to “B”, and turn ON the CNC power.

B Normal mode The maintenance tool menu screen will appear on the VDS. Select

the required tool from the menu and execute. The servo download

function can also be carried out in the normal mode.

Set the main CPU rotary switch to “9”. Set the HR98x rotary switch

Automatic servo 1 to the number of the module to be downloaded, and turn ON the

9 F/W download CNC power. The selected module will be automatfcaiiy~

mode downloaded. Refer to the section titled ‘Servo and spindle

downloading’ for details.

* Supplement : When starting the maintenance tool by a CNC with personal computer,

the tool will not be started if the personal computer side is in a reset status.

3.2 Ending the tool

Turn OFF the CNC power when the operation is finished. The personal computer side is not started

even for a CNC with personal computer, so there is no problem if the CNC power is turned OFF in this

state.

After turning OFF the CNC power, remove the M6 Maintenance Tool cassette and any other cassettes

used in the maintenance. Return the main CPU rotary switch to the setting it was at before carrying out

the operation.

-4-

‘.

3.3 Main menu

The following menu appears on the VDS when the M6 Maintenance Tool is started in the normal mode.

5” (prompt) appears at the bottom of the screen, waiting for the command input. When a menu No.

from the VDS is input and [Enter] is pressed, the screen changes to the corresponding tool function.

**hm** M6 MAINTENANCE TOOL [BND-O23WOll -AO] *wnHr*r\*

Memory Back Up

2) Serial Number and CNC type, Unit type Set

3) Setvo,Spindle F/w Down Load

4) Command Line Mode

> 1 [Enter]

/ \

Prompt Command input (for Memory Back Up)

M6 Maintenance Tool commands

I) Memory Back Up

This command is used to back up the FROM and SFtAM data of cassettes mounted on the on-

board FROM, SFtAM or C-BUS #l to the C-BUS #2 backup cassette.

2) Serial Number and CNC type, Unit type Set

This command is used to set the CNC serial No., CNC type, and unit type.

3) Servo, Spindle Down Load

This command is used to download the servo and spindle F/w to the amplifier.

4) Command tine Mode

This command is used to designate a command and address in the command line and backs it up

to the memory backup.

This command differs from the method for menu commands 1) to 3), in that the commands are

M500 offline monitor-type interactive format commands.

-5-

4. Memory Back Up

This command is used to back up the FROM and SFWM data of cassettes mounted on the on-board

FROM, SRAM or C-BUS #l to the C-BUS #2 backup cassette.

4.1 Preparation

Mount the Maintenance Tool cassette (HR98x) on C-BUS #2. Mount the cassette to be used for

memory backup on the expansion C-BUS of the maintenance tool (HR98x). Refer to the section titled

“Mounting the maintenance tool cassette” for details when mounting the cassette.

HR Series or QX Series ROM cassettes can be used for memory backup.

List of memory cassettes *

Cassette name Remarks

I QX818 I 3MB I OK6 *l

*l : Cassette that can be used for on-board SRAM backup.

+2 : Cassette in which block No. designation and information area setting is possible in the on-

board SRAM backup.

-6-

4.2 Operating procedure

1) Toot selection

Select “1) Memory Back Up” from the M6 Maintenance Tool main screen. (Refer to the section titled

‘Main Menu” for details).

2) Tool menu screen

The following menu appears.

ht**m*nm****+H)L MEMORY BACK UP COMMAND p

[Memory List] :

Bus

Card Mem Size

Mem Size

__________--_______----------------------------

OnBoard HRI 138 From: 0x800000 Sram: 0x080000

C-Bus#l HR437B From: 0x400000 Sram: 0x200000

C-Bus#2 HR437B From: 0x400000 Sram: Ox200000

[Command] :

Q) Quit 0) Restart

1) Write (Memory -> Backup) 2) Read (Backup -> Memory)

3) Compare (Memory c> Backup)

Clear (Memory)

5) Create Info Area 6) Delete info Area

7) Show Info Area

[Select Mem#] :

1 - OnBoard FROM 2 - OnBoard SRAM

3 - C-Bus#l FROM 4 - CBus#l SRAM

>[Command] [Select Mem#l, [Blk#1

> 1 2 [Enter]

@ [Memory List]

This displaysthe FROM and SRAM size of the CPU, the FROM

andthe FROM and SRAM size of C-BUS #2. and SRAM size of C-BUS #1,

0 [Command]

This displaysthe memory backup tool command. Refer to the explanations of the commands

on the following pagesfor details.

@I [Select Memory]

This displaysthe memory in which the data isbacked up.

1 - On-board FROM .............. On-board FROM

2 - On-board SRAM ............... On-board SRAM

3 - C-Bus#l FROM ................ C-Bus#l FROM

4 - C-Bus#l SRAM ................ C-Bus#l SRAM

@I [Command], [Select Mem#], [Blk#]

> COMMAND A MEMORY SELECTION NO., BLOCK

NO. [Enter]

COMMAND:

\ Space

code

Set a command No. shownin [Command].

MEMORY SELECTION NO.:

Set

the No. of a memory shown in [Select Mem#]. This parameter isusedfor the Write,

Read, and Comparecommands.

BLOCK NO.:

Set this only when on-boardSRAM is selected as the memory, and an HR Series ROM

cassette (cassette with a larger capacity than the on-board SFtAM) is

usedasthe backup

cassette. Always designatethe block No. when creating an information area.

-7-

Andere Handbücher für MELDAS 600 Series

Inhaltsverzeichnis

Andere Mitsubishi Electric Elektrowerkzeuge Handbücher

Mitsubishi Electric

Mitsubishi Electric MELDAS 600M Series Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung