Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

General-Purpose AC Servo

CC-Link IE Field Network Interface

Servo Amplifier Instruction Manual

(Motion Mode)

-MR-J4-_GF_

-MR-J4-_GF_-RJ

SAFETY PRECAUTIONS

(Please read the instructions carefully before using the equipment.)

To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read

through this Instruction Manual, Installation guide, and appended documents carefully. Do not use the equipment until you

have a full knowledge of the equipment, safety information and instructions.

In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to conditions.

Please follow the instructions of both levels because they are important to personnel safety.

What must not be done and what must be done are indicated by the following diagrammatic symbols.

In this Instruction Manual, instructions at a lower level than the above, instructions for other functions, and so on are classified

into "POINT".

After reading this Instruction Manual, keep it accessible to the operator.

WARNING Indicates that incorrect handling may cause hazardous conditions, resulting in

death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions, resulting in

minor or moderate injury or property damage.

Indicates what must not be done. For example, "No Fire" is indicated by .

Indicates what must be done. For example, grounding is indicated by .

[To prevent electric shock, note the following]

[To prevent fire, note the following]

WARNING

●Before wiring and inspections, turn off the power and wait for 15 minutes or more until the charge

lamp turns off. Then, confirm that the voltage between P+ and N- is safe with a voltage tester and

others. Otherwise, an electric shock may occur. In addition, when confirming whether the charge lamp

is off or not, always confirm it from the front of the servo amplifier.

●Ground the servo amplifier and servo motor securely.

●Any person who is involved in wiring and inspection should be fully competent to do the work.

●Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, it

may cause an electric shock.

●Do not operate switches with wet hands. Otherwise, it may cause an electric shock.

●The cables should not be damaged, stressed, loaded, or pinched. Otherwise, it may cause an electric

shock.

●During power-on or operation, do not open the front cover of the servo amplifier. Otherwise, it may

cause an electric shock.

●Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging

area are exposed and you may get an electric shock.

●Except for wiring and periodic inspection, do not remove the front cover of the servo amplifier even if

the power is off. The servo amplifier is charged and you may get an electric shock.

●To prevent an electric shock, always connect the protective earth (PE) terminal (marked ) of the

servo amplifier to the protective earth (PE) of the cabinet.

●To avoid an electric shock, insulate the connections of the power supply terminals.

CAUTION

●Install the servo amplifier, servo motor, and regenerative resistor on incombustible material. Installing

them directly or close to combustibles will lead to smoke or a fire.

●Always connect a magnetic contactor between the power supply and the main circuit power supply

(L1/L2/L3) of the servo amplifier, in order to configure a circuit that shuts down the power supply on

the side of the servo amplifier’s power supply. If a magnetic contactor is not connected, continuous

flow of a large current may cause smoke or a fire when the servo amplifier malfunctions.

●Always connect a molded-case circuit breaker, or a fuse to each servo amplifier between the power

supply and the main circuit power supply (L1/L2/L3) of the servo amplifier, in order to configure a

circuit that shuts down the power supply on the side of the servo amplifier’s power supply. If a molded-

case circuit breaker or fuse is not connected, continuous flow of a large current may cause smoke or

a fire when the servo amplifier malfunctions.

●When using the regenerative resistor, switch power off with the alarm signal. Otherwise, a

regenerative transistor malfunction or the like may overheat the regenerative resistor, causing smoke

or a fire.

●Provide adequate protection to prevent screws and other conductive matter, oil and other combustible

matter from entering the servo amplifier and servo motor.

[To prevent injury, note the following]

CAUTION

●Only the power/signal specified in the Instruction Manual should be applied to each terminal.

Otherwise, it may cause an electric shock, fire, injury, etc.

●Connect cables to the correct terminals. Otherwise, a burst, damage, etc., may occur.

●Ensure that polarity (+/-) is correct. Otherwise, a burst, damage, etc., may occur.

●The servo amplifier heat sink, regenerative resistor, servo motor, etc., may be hot while the power is

on and for some time after power-off. Take safety measures such as providing covers to avoid

accidentally touching them by hands and parts such as cables.

[Additional instructions]

[Transportation and installation]

The following instructions should also be fully noted. Incorrect handling may cause a malfunction, injury, electric shock, fire,

etc.

CAUTION

●Transport the products correctly according to their mass.

●Stacking in excess of the specified number of product packages is not allowed.

●Do not hold the front cover, cables, or connectors when carrying the servo amplifier. Otherwise, it may

drop.

●Install the servo amplifier and the servo motor in a load-bearing place in accordance with the

Instruction Manual.

●Do not get on or put heavy load on the equipment. Otherwise, it may cause injury.

●The equipment must be installed in the specified direction.

●Maintain specified clearances between the servo amplifier and the inner surfaces of a control cabinet

or other equipment.

●Do not install or operate the servo amplifier and servo motor which have been damaged or have any

parts missing.

●Do not block the intake and exhaust areas of the servo amplifier. Otherwise, it may cause a

malfunction.

●Do not drop or apply heavy impact on the servo amplifiers and the servo motors. Otherwise, it may

cause injury, malfunction, etc.

●Do not strike the connector. Otherwise, it may cause a connection failure, malfunction, etc.

●When you keep or use the equipment, please fulfill the following environment.

●When the product has been stored for an extended period of time, contact your local sales office.

●When handling the servo motor, be careful with the sharp edges of the servo motor.

●The servo amplifier must be installed in a metal cabinet.

●When fumigants that contain halogen materials, such as fluorine, chlorine, bromine, and iodine, are

used for disinfecting and protecting wooden packaging from insects, they cause a malfunction when

entering our products. Please take necessary precautions to ensure that remaining materials from

fumigant do not enter our products, or treat packaging with methods other than fumigation, such as

heat treatment. Additionally, disinfect and protect wood from insects before packing the products.

●To prevent a fire or injury in case of an earthquake or other natural disasters, securely install, mount,

and wire the servo motor in accordance with the Instruction Manual.

Item Environment

Ambient

temperature

Operation

Storage

Ambient

humidity

Operation

Storage

Ambience

Altitude

Vibration resistance

0 °C to 55 °C (non-freezing)

-20 °C to 65 °C (non-freezing)

5 %RH to 90 %RH (non-condensing)

Indoors (no direct sunlight), free from corrosive gas, flammable gas, oil mist, dust, and dirt

2000 m or less above sea level (Contact your local sales office for the altitude for options.)

5.9 m/s

, at 10 Hz to 55 Hz (X, Y, Z axes)

[Wiring]

[Test run and adjustment]

CAUTION

●Wire the equipment correctly and securely. Otherwise, the servo motor may operate unexpectedly.

●Make sure to connect the cables and connectors by using the fixing screws and the locking

mechanism. Otherwise, the cables and connectors may be disconnected during operation.

●Do not install a power capacitor, surge killer, or radio noise filter (optional FR-BIF(-H)) on the servo

amplifier output side.

●To avoid a malfunction, connect the wires to the correct phase terminals (U/V/W) of the servo amplifier

and servo motor.

●Connect the servo amplifier power output (U/V/W) to the servo motor power input (U/V/W) directly. Do

not connect a magnetic contactor and others between them. Otherwise, it may cause a malfunction.

●The connection diagrams in this Instruction Manual are shown for sink interfaces, unless stated

otherwise.

●The surge absorbing diode installed to the DC relay for control output should be fitted in the specified

direction. Otherwise, the converter unit and the drive unit will malfunction and will not output signals,

disabling the emergency stop and other protective circuits.

●When the wires are not tightened enough to the terminal block, the wires or terminal block may

generate heat because of the poor contact. Be sure to tighten the wires with specified torque.

●Connecting a servo motor of the wrong axis to U, V, W, or CN2 of the servo amplifier may cause a

malfunction.

●Configure a circuit to turn off EM2 or EM1 when the main circuit power supply is turned off to prevent

an unexpected restart of the servo amplifier.

●To prevent malfunction, avoid bundling power lines (input/output) and signal cables together or

running them in parallel to each other. Separate the power lines from the signal cables.

CAUTION

●When executing a test run, follow the notice and procedures in this instruction manual. Otherwise, it

may cause a malfunction, damage to the machine, or injury.

●Before operation, check and adjust the parameter settings. Improper settings may cause some

machines to operate unexpectedly.

●Never make a drastic adjustment or change to the parameter values as doing so will make the

operation unstable.

●Do not get close to moving parts during the servo-on status.

Servo motor

Servo amplifier Servo motorServo amplifier

24 V DC

DOCOM

Control output

signal

Servo amplifier

For sink output interface

24 V DC

DOCOM

Control output

signal

Servo amplifier

For source output interface

[Usage]

CAUTION

●Provide an external emergency stop circuit to stop the operation and shut the power off immediately.

●For equipment in which the moving part of the machine may collide against the load side, install a limit

switch or stopper to the end of the moving part. The machine may be damaged due to a collision.

●Do not disassemble, repair, or modify the product. Otherwise, it may cause an electric shock, fire,

injury, etc. Disassembled, repaired, and/or modified products are not covered under warranty.

●Before resetting an alarm, make sure that the run signal of the servo amplifier is off in order to prevent

a sudden restart. Otherwise, it may cause an accident.

●Use a noise filter, etc., to minimize the influence of electromagnetic interference. Electromagnetic

interference may affect the electronic equipment used near the servo amplifier.

●Do not burn or destroy the servo amplifier. Doing so may generate a toxic gas.

●Use the servo amplifier with the specified servo motor.

●Wire options and peripheral equipment, etc. correctly in the specified combination. Otherwise, it may

cause an electric shock, fire, injury, etc.

●The electromagnetic brake on the servo motor is designed to hold the motor shaft and should not be

used for ordinary braking.

●For such reasons as incorrect wiring, service life, and mechanical structure (e.g. where a ball screw

and the servo motor are coupled via a timing belt), the electromagnetic brake may not hold the motor

shaft. To ensure safety, install a stopper on the machine side.

●If the dynamic brake is activated at power-off, alarm occurrence, etc., do not rotate the servo motor by

an external force. Otherwise, it may cause a fire.

[Corrective actions]

[Maintenance, inspection and parts replacement]

[General instruction]

CAUTION

●Ensure safety by confirming the power off, etc. before performing corrective actions. Otherwise, it may

cause an accident.

●If it is assumed that a power failure, machine stoppage, or product malfunction may result in a

hazardous situation, use a servo motor with an electromagnetic brake or provide an external brake

system for holding purpose to prevent such hazard.

●Configure an electromagnetic brake circuit which is interlocked with an external emergency stop

switch.

●When an alarm occurs, eliminate its cause, ensure safety, and deactivate the alarm to restart

operation.

●If the molded-case circuit breaker or fuse is activated, be sure to remove the cause and secure safety

before switching the power on. If necessary, replace the servo amplifier and recheck the wiring.

Otherwise, it may cause smoke, fire, or an electric shock.

●Provide an adequate protection to prevent unexpected restart after an instantaneous power failure.

●After an earthquake or other natural disasters, ensure safety by checking the conditions of the

installation, mounting, wiring, and equipment before switching the power on to prevent an electric

shock, injury, or fire.

CAUTION

●Make sure that the emergency stop circuit operates properly such that an operation can be stopped

immediately and a power is shut off by the emergency stop switch.

●It is recommended that the servo amplifier be replaced every 10 years when it is used in general

environment.

●When using the servo amplifier that has not been energized for an extended period of time, contact

your local sales office.

●To illustrate details, the equipment in the diagrams of this Instruction Manual may have been drawn

without covers and safety guards. When the equipment is operated, the covers and safety guards

must be installed as specified. Operation must be performed in accordance with this Instruction

Manual.

Servo motor

Electromagnetic brake

Contacts must be opened with

the emergency stop switch.

Contacts must be opened when ALM

(Malfunction) or MBR (Electromagnetic

brake interlock) turns off.

24 V DC

DISPOSAL OF WASTE

• Please dispose a servo amplifier, battery (primary battery) and other options according to your local laws and regulations.

EEP-ROM LIFE

The number of write times to the EEP-ROM, which stores parameter settings, etc., is limited to 100,000. If the total number of

the following operations exceeds 100,000, the servo amplifier may malfunction when the EEP-ROM reaches the end of its

useful life.

• Write to the EEP-ROM due to parameter setting changes

• Write to the EEP-ROM due to device changes

STO FUNCTION OF THE SERVO AMPLIFIER

When using the STO function of the servo amplifier, refer to the following.

Page 453 USING STO FUNCTION

For the MR-J3-D05 safety logic unit, refer to the following.

Page 586 MR-J3-D05 Safety logic unit

COMPLIANCE WITH GLOBAL STANDARDS

For the compliance with global standards, refer to the following.

Page 572 Compliance with global standards

Andere Handbücher für MELSERVO-J4 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Servoantrieb Handbücher

Mitsubishi Electric

Mitsubishi Electric MELSERVO HG-MR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J5 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J4-B Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-HP30KA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-Jet HG-SNS Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET-G-N1 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4-*B-RJ010 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4-10A(-RJ) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric TM-RFM Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric HG-KN Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric HG-MR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4W2-0303B6 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2S-*A series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J5 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E700EX Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-MT2010 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-H Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MRZJW3- SETUP161E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2S-60A4 Kurzanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E700EX Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-D30 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric TM-RFM Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4-10B(-RJ) Bedienungsanleitung

Beliebte Servoantrieb Handbücher anderer Marken

Robotis

Robotis XH430-W350-T Bedienungsanleitung

NTI AG

NTI AG LinMot C1250 Series Bedienungsanleitung

Parallax

Parallax 900-00005 Bedienungsanleitung

Festo

Festo TP 1410 Bedienungsanleitung

Axor

Axor MAGNUM 400 Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Bedienungsanleitung

Danfoss

Danfoss 176F6494 Bedienungsanleitung

THORLABS

THORLABS TDC001 Bedienungsanleitung

TECO

TECO JSDAP Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Bedienungsanleitung

GSK

GSK DA98D Bedienungsanleitung

Lenze

Lenze m850 Leitfaden

Baumuller

Baumuller b maXX 3000 Handbuch

Baumuller

Baumuller b maXX 5000 Handbuch

Baumuller

Baumuller b maXX 5500 Handbuch

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Omron

Omron CK5M-CPU 1 Series Benutzerhandbuch

ABB

ABB ACS350 Series Bedienungsanleitung