Mitsubishi Heavy Industries KX6 series Bedienungsanleitung

(OUTDOOR UNIT)

KX6 series

FDC224KXE6, 280KXE6, 335KXE6

FDC224KXE6M, 280KXE6M, 335KXE6M

FDCS224KXE6M, 280KXE6M, 335KXE6M (Corrosin Protection Treatment series)

(Heat pump type)

Manual No. '10

• KX-SM-148

SERVICE MANUAL

Regarding the Duct Connected-High static Pressure-type Outdoor Air Processing Unit

Series (FDU500〜1800FKXE6D), refer to the DATA BOOK No.'10 •KX-DB-144

• Note:

VRF INVERTER MULTI-SYSTEM AIR CONDITIONERS

Alternative refrigerant R410A use models

FDT28KXE6D

FDT36KXE6D

FDT45KXE6D

FDT56KXE6D

FDT71KXE6D

FDT90KXE6D

FDT112KXE6D

FDT140KXE6D

FDT160KXE6D

FDTC22KXE6D

FDTC28KXE6D

FDTC36KXE6D

FDTC45KXE6D

FDTC56KXE6D

FDU224KXE6D

FDU280KXE6D

FDTW28KXE6D

FDTW45KXE6D

FDTW56KXE6D

FDTS45KXE6D

FDTS71KXE6D

FDTQ22KXE6D

FDTQ28KXE6D

FDTQ36KXE6D

(INDOOR UNIT)

KX6 series

FDFW28KXE6D

FDFW45KXE6D

FDFW56KXE6D

FDU500FKXE6D

FDU850FKXE6D

FDU1300FKXE6D

FDU1800FKXE6D

FDUM22KXE6D

FDUM28KXE6D

FDUM36KXE6D

FDUM45KXE6D

FDUM56KXE6D

FDUM71KXE6D

FDUM90KXE6D

FDUM112KXE6D

FDUM140KXE6D

FDUT22KXE6D

FDUT28KXE6D

FDUT36KXE6D

FDUT45KXE6D

FDUT56KXE6D

FDK22KXE6D

FDK28KXE6D

FDK36KXE6D

FDK45KXE6D

FDK56KXE6D

FDK71KXE6D

FDUH22KXE6D

FDUH28KXE6D

FDUH36KXE6D

FDE36KXE6D

FDE45KXE6D

FDE56KXE6D

FDE71KXE6D

FDE112KXE6D

FDE140KXE6D

60Hz only

INVERTER DRIVEN MULTI-INDOOR-UNIT

CLIMATE CONTROL SYSTEM

Air-Conditioning & Refrigeration Systems Headquarters

16-5, 2-chome, Kounan, Minato-ku, Tokyo, 108-8215, Japan

Fax : (03) 6716-5926

No.108 R

'10 • KX-SM-148

CONTENTS

1 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER ..................... 1

1.1 Wired remote controller (Opition parts) ......................................................... 1

1.2 Operation control function by the indoor controller ....................................... 2

1.3 Operation control function by the remote controller ...................................... 8

1.4 Operation control function by the outdoor controller ..................................... 9

2 SYSTEM TROUBLESHOOTING PROCEDURE ............................................. 40

2.1 Basics of troubleshooting ............................................................................ 40

2.2 Explanation of troubleshooting.................................................................... 41

2.3 Contents of troubleshooting ........................................................................ 42

2.4 Outdoor unit control PCB replacement procedure ...................................... 97

2.5 Inverter PCB replacement procedure.......................................................... 99

3 ELECTRICAL WIRING ................................................................................. 103

3.1 Outdoor unit .............................................................................................. 103

3.2 Indoor unit ................................................................................................. 105

4 PIPING SYSTEM............................................................................................ 123

5 APPLICATION DATA .................................................................................... 125

5.1 Installation of outdoor unit ......................................................................... 125

(1) Ceiling cassette-4 way type (FDT)..................................................... 126

(2) Ceiling cassette-4 way compact type (FDTC).................................... 131

(3) Ceiling cassette-2 way type (FDTW) ................................................. 136

(4) Ceiling cassette-1 way compact type (FDTQ) ................................... 139

(5) Ceiling cassette-1 way type (FDTS) .................................................. 147

(6) Duct connected-High static pressure type (FDU) .............................. 150

(7) Duct connected-Low/Middle static pressure type (FDUM)................. 153

(8) Duct connected (thin)-Low static pressure type (FDUT).................... 156

(9) Duct connected-Compact and Flexible type (FDUH)......................... 159

(10) Wall mounted type (FDK) .................................................................. 162

(11) Ceiling suspended type (FDE)........................................................... 165

(12) Floor standing-2 way type (FDFW) .................................................... 168

(13) Outdoor air processing unit (FDU-F).................................................. 171

5.2 Electric wiring work instruction .................................................................. 174

5.3 Installation manual for wired remote controller (Option parts : RC-E4)..... 179

5.4 Installation of outdoor unit ......................................................................... 184

5.5 Method for connecting the accessory pipe................................................ 200

5.6 Check operation procedure....................................................................... 201

5.7 Instructions for installing the branch pipe set ............................................ 209

6 CORROSION PROTECTION TRETMENT SERIES ...................................... 213

'10 • KX-SM-148

1. OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER

1.1 Wired remote controller (Option parts)

The gure below shows the remote controller with the cover opened. Note that all the items that may be displayed in the liquid crystal

display area are shown in the gure for the sake of explanation.

Characters displayed with dots in the liquid crystal display area are abbreviated.

Pull the cover downward to open it.

＊ All displays are described in the liguid crystal display for explanation.

The figure below shows the remote control with the cover opened.

Installation of remote control

DO NOT install it on the following places in order to avoid malfunction.

(1) Places exposed to direct sunlight

(2) Places near heat devices

(3) High humidity places

(4) Hot surface or cold surface enough to generate condensation

(5) Places exposed to oil mist or steam directly

(6) Uneven surface

Cover

This button is used to fix the setting.

This button is used to set the silent mode.

'10 • KX-SM-148

1.2 Operation control function by the indoor controller

(1) Operations of functional items during cooling/heating

Cooling Heating

Dehumidify

Fan

Operation

Functional item

Thermostat

OFF

Thermostat

OFF

Hot start

(Defrost)

Compressor

4-way valve

Outdoor fan

Indoor fan

Louver motor

Drain pump (4)

















/

(2)





(2)





/











/

/(2)



()





/



/

Thermostat ON:



Thermostat OFF: (2)

Note (1) : Operation : Stop /: Turned ON/OFF by the control other than the room temperature control.

(2) ON during the drain motor delay control

(3) Drain pump ON setting may be selected by the indoor unit function setting of the wired remote controller.

(2) Dehumidifying operation

(a) When the humidity sensor is not provided (Models other than FDT Series)

return air thermistor [ThI-A (by the remote controller when the remote control sensor is enabled)] controls the indoor

temperature environment simultaneously.

1) Operation is started in the cooling mode. When the difference between the return air thermistor and the setting

temperature is 2°C or less, the indoor unit fan tap is brought down by one tap. That tap is retained for 3 minutes

after changing the indoor fan tap.

Note (1) In case of “P-Hi”, change the tap down to “Hi”.

(2) Lower limit of tap-down for the indoor air volume is Lo tap.

2) If the suction air temperature exceeds the setting temperature 3°C or more during defrosting operation, the indoor

fan tap is raised by one tap. That tap is retained for 3 minutes after changing the indoor fan tap.

Note (1) Upper limit of tap-up for the indoor air volume is the setting air volume.

3) If the thermostat OFF is established during the above control, the indoor fan tap at the thermostat ON is retained so

far as the thermostat is turned OFF.

4) After stopping the cooling operation, the indoor unit continues to run at Lo for 15 seconds.

(3) Timer operation

(a) Timer

Set the duration of time from the present to the time to turn off the air-conditioner.

It can be selected from 10 steps in the range from “OFF 1 hour later” to “OFF 10 hours later”. After the clock timer

setting, the remaining time is displayed with progress of time in the unit of hour.

(b) OFF timer

Time to turn OFF the air-conditioner can be set in the unit of 10 minutes.

Time to turn ON the air-conditioner can be set. Indoor temperature can be set simultaneously.

(d) Weekly timer

Timer operation (ON timer, OFF timer) can be set up to 4 times a day for each weekday.

(e) Timer operations which can be set in combination

Timer

OFF timer

ON timer

Weekly timer

Timer







OFF timer







ON timer





Weekly timer



Note (1) : Allowed : Not

ESP-FP-1730

'10 • KX-SM-148

(4) Remote controller display during the operation stop

(a) “Centralized control ON” is displayed always on the LCD under the “Center/Remote” and “Center” modes during the

operation stop (Power ON). This is not displayed under the “Remote” mode.

(b) If this display is not shown under the “Center/Remote” mode, check if the indoor unit power switch is turned on or not.

(5) Hot start (Prevention of cold draft during heating)

At the startup of heating operation, at resetting the thermostat, during defrosting operation and at returning to heating, the

indoor fan is controlled by the indoor heat exchanger temperature (detected with ThI-R) to prevent the cold draft.

Judgment by heating start thermostat

Normal condition/Set airflow volume

Thermostat OFF Thermostat ON

Compressor OFFCompressor ON End of defrosting

Heat exchanger temp. 35˚C or higher, or after 7 minutes Heat exchanger temp. 35˚C or higher, or after 7 minutes

Defrosting start

Fan

or ULQ

or ULo

Set airflow volume

Indoor heat exchanger temp. (˚C)

35 45

25 35

Indoor heat exchanger temp. (˚C)

Set airflow volume

Fan

OFF

or ULo

25 35 45

Set airflow volume

Fan

OFF

Indoor heat exchanger temp. (˚C)

Fan

or ULo

（1）

Note (1) Heating preparation is displayed during the hot start (when the compressor is operating and the indoor fan does not provide the set airow volume).

(6) Hot keep

Hot keep control is performed at the start of the defrost control.

(a) Control

1) When the indoor heat exchanger temperature (detected with ThI-R1 or R2) drops to 35°C or lower, indoor fan is

changed to the lower tap at each setting.

2) During the hot keep operation, the louver horizontal control signal is transmitted.

(b) Ending condition

When the indoor fan is at the lower tap at each setting, it returns to the set airow volume as the indoor heat exchanger

temperature rises to 45°C or higher.

(7) Fan control during the heating thermostat OFF

When the heating thermostat is turned OFF, the setting of the fan control is selectable with using the indoor function of wired

remote controller [　　　　　].

(a) Low speed (Factory default)

If the indoor heat exchanger temperature drops 35°C or lower with the heating thermostat OFF, the indoor fan operate at

the lower speed tap at each setting.

(b) Set airow volume

Even if the indoor heat exchanger temperature drops 35°C or lower with the heating thermostat OFF, the indoor fan

continues to run at the set airow volume.

If the indoor heat exchanger temperature drops 35°C or lower with the heating thermostat OFF, the indoor fan operates at

the lower speed tap at each setting and, when the indoor heater exchanger temperature drops 25°C or lower, the indoor fan

stops for 5 minutes. Then the fan runs at the slow speed tap for 2 minutes, and the judgment is made by the thermostat.

(d) Stop

If the indoor heat exchanger temperature drops 35°C or lower with the heating thermostat OFF, the indoor fan is turned

OFF. The same applies also when the remote controller sensor is effective.

'10 • KX-SM-148

(8) Filter sign

As the operation time (when ON/OFF switch is at ON) accumulates to 180 hours (1), “Filter cleaning” is displayed on the

remote controller. (This is also displayed when the unit is in trouble and under the centralized control, regardless of ON/OFF)

Note (1) Time setting for the lter sign can be made as shown below using the indoor function of wired remote controller “Filter sign setting”. (It is set at 1 at the

shipping from factory.)

Filter Sign Setting

Setting 1

Setting 2

Setting 3

Setting 4

Function

Setting time: 180 hrs (Factory default)

Setting time: 600 hrs

Setting time: 1,000 hrs

Setting time: 1,000 hrs (Unit stop)

(2)

After the setting time has elapsed, the “Filter cleaning” is displayed and, after operating for 24 hours further (counted also during the stop), the unit stops.

(9) Auto swing control [Applicable model: FDT, FDTC, FDTW FDTS, FDTQ (Excepted duct panel) and FDE]

(a) Louver control

(i) Press the [Louver] button to operate the swing louver when the air conditioner is operating.

“Auto wind direction” is displayed for 3 seconds and then the swing louver moves up and down continuously.

(ii) To x the swing louver at a position, press one time the [Louver] button while the swing louver is moving so that

four stop positions are displayed one after another per second.

When a desired stop position is displayed, press the [Louver] button again. The display stops, changes to show the

“Louver stop” for 5 seconds and then the swing louver stops.

(iii) Louver operation at the power on

The louver swings one time automatically (without operating the remote controller) at the power on.

This allows inputting the louver motor (LM) position, which is necessary for the microcomputer to recognize the

louver position.

Note (1) If you press the Louver button, the swing motion is displayed on the louver position LCD for 10 second. The display changes to the “Auto wind

direction” display 3 seconds later.

(b) Automatic louver level setting during heating

While hot start operation and heating thermostat OFF operation, the louver keeps the level position (In order to prevent

the cold draft) whether the auto swing switch is operated or not (auto swing or louver stop), The louver position display

LCD continues to show the display which has been shown before entering this control.

When the louver-free stop has been selected with the indoor function of wired remote controller “Louver control setting”,

the louver motor stops when it receives the stop signal from the remote controller. If the auto swing signal is received

from the remote controller, the auto swing will start from the position where it was before the stop.

Note (1) When the indoor function of wired remote controller “Louver control setting” has been switched, switch also the remote control function “Louver

control setting” in the same way.

(d) Individual flap (louver) control system

Regarding FDT and FDTC models, the individual f laps (louvers) for 4 directions can be controlled to swing within the

ranges between upper limit and lower limit selected with wired remote control respectively.

For detail setting method, refer to ⑦ in page 135 for FDTC or ⑨ in page 130 for FDT.

The single f lap (louver) of FDE model can also be controlled to swing like FDT and FDTC.(refer to ⑪ in page 000 for details)

Note (1) The function is not able to be set with wireless remote controls or simple remote control (RCH-E3)

(10) Compressor inching prevention control

(a) Once the indoor unit thermostat has been turned ON, the thermostat is not turned OFF for 2 minutes (*1) after the

compressor ON even if the thermostat is turned OFF at the state of (1).

(b) When the oil return control has started while the thermostat is turned ON, the thermostat is not turned OFF even if the

thermostat OFF condition is met during the oil return control.

Thermostat ON/OFF with this control

2 minutes2 minutes

OFF

Stopped by remote controller, etc.

＊1

＊1Even when the thermostat of another indoor

unit is turned ON after the compressor ON,

the thermostat is not turned OFF for 2 minutes

after the compressor ON.

＊1

OFF

3 minutes delay

Thermostat OFF in the condition of (1)

Compressor

Indoor unit A

Thermostat

Indoor unit B

Thermostat

'10 • KX-SM-148

(11) Drain motor (DM) control [Applicable type: FDT, FDTC, FDTW, FDTS, FDTQ, FDUM, FDQS and FDU90～140]

(a) Drain motor (DM) start operation at the same time when compressor ON at cooling and dehumidifying mode and

keeps operating for 5 minutes after operation stop, the anomalous stop, thermostat OFF and switching from cooling or

dehumidifying operation to fan or heating operation.

Stop (1)

Indoor unit operation mode

Control A

Control B

Compressor ON

Compressor OFF

Cooling

Dehumidifying

HeatingFan (2) Note (1) Including the stop from cooling, dehumidifying,

fan and heating operation and the anomalous stop.

(2) Including the “Fan” operation according to the

mismatch of operation modes.

(i) Control A

1) If the oat switch detects any anomalous draining condition, the unit stops with the anomalous stop (displays E9)

and the drain pump starts.

2) The drain motor keeps operating while the oat switch is detecting the anomalous condition.

(ii) Control B

If the oat switch detects any anomalous drain condition, the drain motor is turned ON for 5 minutes, and at 10 seconds

after the drain motor OFF it checks the oat switch. If it is normal, the unit is stopped under the normal condition or, if

there is any anomalous condition, E9 is displayed and the drain motor is turned ON. (The ON condition is maintained

during the drain detection.)

(b) Drain motor (DM) interlock control

(i) Start conditions

Depending on the function setting of the remote controller, the drain motor is turned ON under either one of the

following conditions.

1) During heating operation (Both the thermostat ON/OFF)

2) During heating operation (Both the thermostat ON/OFF) + Fan operation

3) Fan operation

(ii) Stop conditions

The drain motor is turned OFF 5 minutes after the stop of operations 1) to 3) above.

(12) Operation check/drain pump test run operation mode

(a) If the power is turned on when the dip switch (SW7-1) on the indoor PCB is ON state, it enters the mode of operation

check/drain pump test run. It is ineffective (prohibited) to change the switch after turning power on.

(b) When the communication with the remote controller has been established within 60 seconds after turning power on by the

dip switch (SW7-1) ON, it enters the operation check mode. Unless the remote controller communication is established, it

enters the drain pump test run mode.

Note (1) To select the drain pump test run mode, disconnect the remote control connector (CNB) on the indoor PCB to shut down the remote controller

communication.

There is no communication with the outdoor unit but it allows performing operation in respective modes by operating the

remote controller.

(d) Drain pump test run mode

When the drain pump test run is established, only the drain pump operates, and during operation the protective functions

by the microcomputer of indoor unit become ineffective.

(13) Indoor heat exchanger anti-frost (anti-frost control)

Thermostat OFF control

(a) Thermostat is turned OFF depending on the temperature detected with the heat exchanger sensor (ThI-R1, R2) during

“Cooling” and “Dehumidifying” operations.

1.0

Forced thermostat OFF

Thermostat ON OK

Heat exchanger temperature

5-min timer

Temperature drop

Temperature rising

10°C

(b) For 4 minutes after the thermostat ON, the forced thermostat OFF control for the anti-frost protection is not effective.

a) When temperatures detected by the heat exchanger sensors ThI-R1 and R2 are higher than the anti-frost protection

temperature at 4 minutes after the thermostat ON, the detection starts from the state of thermostat ON.

temperature (-0.5°C) continuously for 5 minutes after 4 minutes of the thermostat ON operation, then the thermostat is

turned OFF forcibly.

The thermostat will be turned ON if temperatures detected by ThI-Ra and R2 picked up in the thermostat ON range.

(d) “Anti-frost” signal is sent to the outdoor unit.

'10 • KX-SM-148

(14) Anomalous fan motor (FDT,FDTC,FDFW and FDK only)

Fan motor will be stopped with displaying “E16”, if it has detected the revolutions of 200 rpm or less continuously for 30

seconds at a rate of 4 times within 60 minutes, after starting the motor.

(15) High ceiling control [Applicable type: FDT, FDTC, FDTW, FDTS and FDE]

In the case of indoor unit installed in a higher ceiling room, the airow volume mode control can be changed with the wired

remote controller indoor unit function “FAN SPEED SET”.

--- -- --

PHi - HiPHi - MePHi - Hi - Me

STANDARD

HIGH SPEED1, 2

FAN SPEED SET Hi - Lo Hi - MeHi - Me - Lo

PHi - PHi - Hi - Me

PHi - Hi - Me - Lo

Indoor unit airflow setting

Fan tap

Note (1) Factory default is Standard.

(2) At the hot-start and heating thermostat OFF, or other, the indoor unit fan is operated at the low speed tap of each setting.

(3) This function is not able to be set with wireless remote comtrols or simple remote control (RCH-E3)

(16) Hot start

Indoor fan motor control is performed at the start of heating operation.

(a) When the temperature detected with the indoor heat exchanger thermistor (ThI-R1 or ThI-R2) drops 35°C or lower, it

control the fan with AC motor: Lo and DC motor: ULo.

(b) When the heat exchanger thermistor detects 45°C or higher with the fan running at Lo/ULo, it returns to the set airow

volume.

Set airflow volume

Lo/ULo

35°C 45°C

Heat exchanger thermistor temp. (ThI-R1 or R2)

(c) On the indoor unit of which the thermostat has been turned OFF during heating operation, the fan is turned OFF if the

heat exchanger thermistor temperature (Thi-R1 or Thi-R2) drops 25°C or lower.

(17) Detection room temperature compensation during heating

With the standard specication, the compressor is turned ON/OFF based on the setting temperature of thermostat. However,

when the thermostat OFF is likely to occur earlier because the unit is installed in a condition that warm air tends to accumulate

near the ceiling, the setting can be changed by using the indoor function of wired remote controller “Heating room temperature

compensation”. Since the compressor is turned ON/OF at one of the setting temperature at +3, +2 or +1°C, the feeling of

heating can be improved. However, the upper limit of setting temperature is 30°C.

Operation

Setting temperature

Room temp. (deg)

–1 +1

Stop

Standard

Compressor

Operation

Setting temperature

Room temp. (deg)

+4+2

Stop

With setting at +3°C

Compressor

(18) Return air temperature compensation

This is the function to compensate a difference between the detected temperature of the Return air thermistor and the measured

temperature after installation of unit.

(a) It is adjustable in the unit of 0.5°C by using the indoor function of wired remote controller “Return air thermistor

compensation”.

• +1.0°C, +1.5°C and +2.0°C • −1.0°C, −1.5°C and −2.0°C

(b) Since the compensated temperature is transmitted to the remote controller and the outdoor unit, it is controlled with the

compensated temperature.

Note (1) Compensation of detection temperature is effective for the indoor unit sensor only.

(19) External control (Remote display)/Remote operation

Always connect the wired remote controller. Otherwise, you cannot perform the remote operation.

(a) Output for external control (remote display) (Optional remote RUN/STOP monitor kit can be utilized.)

Following output connectors (CNT) are provided on the indoor control PCB. Connect the remote RUN/STOP monitor kit

and pick up respective dry contact signal.

• Operation output: Outputs DC12V relay drive signal during operation.

'10 • KX-SM-148

• Heating output: Outputs DC12V relay drive signal during heating operation.

• Compressor ON output: Outputs DC12V relay drive signal when the compressor is operating.

• Error output: When any anomalous condition occurs, it outputs DC12V relay drive signal.

(b) Remote operation input

Remote operation inputs (switch input, timer input) connectors (CnT) are provided on the indoor control PCB.

However, the remote operation by the CnT is not effective when “Center mode” is selected with the air-conditioner.

(i)

At the shipping from factory [Indoor function of wired remote controller “External input selector” is

set at the level input.]

• Startup at the input signal to CnT OFF  ON [Edge input] … Air-conditioner ON

• Stop at the input signal to CnT ON  OFF [Edge input] … Air-conditioner OFF

*ON

ONON

OFF OFF

OFF

OFF OFF

ONON

OFF

*ON

CnT input

Air-conditioner A

Air-conditioner B

(ii) When the setting is changed to the pulse input at site using the indoor unit function of wired

remote controller “External input selector”

It becomes effective only when the input signal to CnT is changed OFF➝ON and the air-conditioner operation [ON/

OFF] is inverted.

OFF

OFF OFF

OFF

CnT input

Air-conditioner A

Air-conditioner B

This emergency stop signal is used to stop all indoor unis connected to the same outdoor unit in emergency.

(i) The emergency stop control becomes effective if the emergency stop control setting is changed to “Valid” from the

wired controller.

(ii) If the emergency stop [E-63] signal is received from outdoor unit, it is transmitted to the remote controller and

makes stop.

(d) Fresh air processing operation input

(i) If indoor unit controller receive fresh air processing operation signal (*1) or fresh air processing stop signal from

remote controller, it output ON signal or OFF signal from CnD connector respectively.

*1. Operation switch ON at interlock setting and ventilation switch ON at non-interlock setting.

(ii) Output relay is DC12V option and maximum relay load is LY2F (OMRON).

(iii)

In case of interlock setting, if either of indoor units connected to one remote controller is in the state of anomalous stop,

the fresh air processing unit connected to that indoor unit cannot be operated. Other processing units connected to the

indoor units operating normally can be operate.

In case of non-interlock setting, processing unit can start ventilation even though the connected indoor unit is in

anomalous stop.

(iv) In case of interlock setting if indoor unit stops, processing unit also stop.

(v) In case of interlock setting if indoor unit stops with anomalous stop, processing unit also stop.

(vi) If indoor unit is started or stopped from center console, processing unit can start or stop in case of interlock setting,

but it keep stopping in case of non-interlock setting.

(vii) Interlock or non-interlock can be set only on the remote controller.

(20) Dip switch function

Model capacity selection with SW6 0 : OFF, 1 : ON

Model P22 P28 P36 P45 P56 P71 P80 P90 P112 P140 P160 P224 P280

SW6-1 0 1 0 0 0 0 1 0 1 0 1 0 1

SW6-2 0 0 1 0 1 0 0 1 1 0 0 1 1

SW6-3 0 0 0 1 1 0 0 0 0 1 1 1 1

SW6-4 0 0 0 0 0 1 1 1 1 1 1 1 1

Note (1) ON marked with * means ON by a remote

controller switch or other.

'10 • KX-SM-148

1.3 Operation control function by the remote controller

(1) Switching sequence of the operation mode switches of remote controller

Dehumidifying Cooling Fan Heating

(2) [CPU reset]

When the “CHECK” and “GRILL” buttons on the remote controller are pressed at the same time, this function is activated.

This function is same as power supply reset.

(3) [Power failure compensation function]

• This function becomes effective when “POWER FAILURE COMPENSATION SET” is valid by setting the remote controller

functions.

• The remote controller's status is always stored in memory, and after recovery of power, operation is resumed according to

the memory contents. However the auto swing stop position and timer mode are cancelled, but the weekly timer setting is

restored with the holiday setting through all weekdays.

By resetting the clock and cancelling the holiday setting for each weekday after recovery of power, weekly timer setting

becomes effective.

• Contents stored in memory for power failure compenstion are as follows.

Note (1) Item ➅➆ and ➇ are stored in memory regardless of whether the power failure compensation setting is valid or invalid, and silent mode setting is

cancelled regardless of whether the power failure compensation setting is valid or invalid.

➀ Running or Stopping status just before power failure

If it had been operating under OFF timer mode or simple timer mode, memorzed status is as stopping (At the

recovery of power, the timer mode is cancelled but weekly timer setting is changed to the holiday setting through all

weekdays

➁ Operation mode

➂ Fan speed mode

➃ Room temperature setting

➄ Louver auto swing/stop

However, the stop position (position 4) is cancelled and is becomes the level position (position 1).

➅ “Remote control function items”, set with the remote controller function setting (“Indoor unit function items” are

stored in the inoor unit's memory.)

➆ Upper limit value and lower limit value set by temperature setting control.

➇ Clock timer setting and weekly timer setting (Other timer settings are not sotred in memory).

[Parts layout on remote controller PCB]

SW2

SW1

親

子

SW1

SW2

When using multiple remote controllers, the following dispiays or settings

cannot be done with the slave remote controller. It is available only with

the master remote controller.

　Louver position setting (set upper or lower limit of swinging range)

　Setting indoor unit functions

　Setting temperature range

　Operation data display

　Error data display

　Silent mode setting

　Test operation of drain pump

　Change the address set by autamatic address setting method (Kx multi only)

　Address setting of master indoor unit (Kx multi only)

　Remote controller sensor setting

Master/ slave setting when more than one remote controllers are used

A maximum of two remote controllers can be connected to one indoor unit (or one group of indoor units.)

Remote controller cord (no polarity)

Remote controller

SW1 "Master"

Switch Setting Contents

M Master remote controller

SW1 S Slave remote controller

Remote controller

SW1 "Slave"

Indoor units

Note (1) Don’t change SW2 because it is not used normally.

Caution

➈

➉

Andere Handbücher für KX6 series

Inhaltsverzeichnis

Andere Mitsubishi Heavy Industries Klimaanlage Handbücher

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK35ZSP-W Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK17ZMP-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries DXK18Z6-W Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK63ZRA-W Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries FDTC Series Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK20HG Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK20ZJ-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRC50HE-S1 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK100VNXPZSX Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK100ZR-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries LMK Series Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK20ZIX-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries FDTC40ZIXVD Produkthandbuch

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK20ZMX-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK25QA-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK20ZSPR-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRF25ZMX-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries FDT71VNPVF1 Produkthandbuch

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries KXZ Series Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK50HE-S1 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK09CJ Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries DXK06ZSA-W Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SRK63ZM-S Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries FDTC40ZHXV Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung