Mitsubishi MELSEC Q Series Bedienungsanleitung

User's Manual

(Hardware)

QJ71MES96

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-Q Series.

MES Interface Module

Prior to use, please read both this manual and detailed manual

thoroughly to fully understand the product.

Model QJ71MES96-U-HW

MODEL

CODE 13JY02

IB(NA)-0800354-C(0809)MEE

A-1

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

Note that these precautions apply only to this product.

For the safety precautions of the programmable controller system, please read the

User's Manual for the CPU module used.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to

the circumstances.

Always follow the instructions of both levels because they are important to

personal safety.

Please save this manual to make it accessible when required and always forward

it to the end user.

DANGER

Indicates that incorrect handling may cause

hazardous conditions, resulting in death or severe

injury.

CAUTION

Indicates that incorrect handling may cause

hazardous conditions, resulting in medium or slight

personal injury or physical damage.

A-2

[Design Precautions]

DANGER

When controlling a running programmable controller (e.g. data modification),

create an interlock circuit on sequence programs so that the whole system

functions safely all the time.

Also, be sure to read the manual carefully and ensure safety before

performing any other controls such as operating status change.

Especially, when controlling a programmable controller from a remote

location via network, problems on the programmable controller side may not

be dealt with promptly due to failure of data communications.

Create an interlock circuit on a sequence program.

For the operation status of each station at a communication error, refer to the

manual for that station.

Incorrect output or malfunctions may cause an accident.

Install a safety circuit external to the programmable controller that keeps the

entire system safe even when there are problems with the external power

supply or the programmable controller.

Otherwise, trouble could result from erroneous output or erroneous

operation.

When the programmable controller system security needs to be protected

against illegal access from an external device via a network, take measures

at the user's discretion.

Do not write any data to the "System area" in the buffer memory of the

intelligent function module.

As for signals output from the programmable controller CPU to the intelligent

function module, never output (ON) a "Use prohibited" signal.

Doing these operations may cause malfunctions of the programmable

controller system.

A-3

[Design Precautions]

[Installation Precautions]

CAUTION

Do not bunch the control wires or communication cables with the main circuit

or power wires, or install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

During registering each setting, do not power OFF the mounted module or

reset the programmable controller CPU.

Otherwise, data in the CompactFlash card will be undefined. Therefore,

resetting and re-registering data are required.

This may also cause a module failure or malfunctions.

CAUTION

Use the programmable controller under the environment specified in the

User's Manual.

Using this programmable controller in an environment outside the range of

the general specifications could result in electric shock, fire, erroneous

operation, and damage to or deterioration of the product.

While pressing the installation lever located at the bottom of module, insert

the module fixing tab into the fixing hole in the base unit until it stops. Then,

securely mount the module with the fixing hole as a supporting point.

Incorrect loading of the module can cause a malfunction, failure or drop.

When using the programmable controller in the environment of much

vibration, tighten the module with a screw.

A-4

[Installation Precautions]

[Wiring Precautions]

CAUTION

Completely turn off the externally supplied power used in the system before

mounting or removing the module.

Not doing so could result in damage to the product.

Tighten the screw in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage

to the screw or module.

Do not directly touch the module's conductive parts or electronic

components.

Touching the conductive parts could cause an operation failure or give

damage to the module.

When connecting a connector, properly press, crimp, or solder it using the

tools specified by the manufacturer.

Incomplete connection may cause short-circuit, fire, and malfunctions.

Push the CompactFlash card into the CompactFlash card slot and install it

securely.

After installing the CompactFlash card, check that it is inserted securely.

Failure to do so may cause malfunctions due to poor contact.

CAUTION

Always store the communication cables and power cables connected to the

module in the duct or fix them in place with clamps.

Not doing so may cause swing, move, or poor connection of the cable, or

damage of a module and/or cable due to careless pull, resulting in

malfunctions.

Install connectors securely to modules.

A-5

[Wiring Precautions]

[Disposal Precautions]

[Transportation Precautions]

CAUTION

Tighten the screw in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage

to the screw or module.

When disconnecting communication cables connected to the module, never

pull on the cable section.

When using a cable with a connector, disconnect it with holding the

connector connected to the module.

When the cable is pulled while connected to the module, this may cause

malfunctions or module/cable damage.

Be sure there are no foreign substances such as sawdust or wiring debris

inside the module.

Such debris could cause fires, damage, or erroneous operation.

The module has an ingress prevention label on its top to prevent foreign

matter, such as wire offcuts, from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat

dissipation.

CAUTION

When disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to

the local regulations. (For details of the battery directive in EU member

states, refer to the MES Interface Module User's Manual.)

CAUTION

When transporting lithium batteries, make sure to treat them based on the

transportation regulations. (Refer to Chapter8 for details of the relevant

models.)

A-6

Revisions

* The manual number is given on the bottom right of the front cover.

Print date * Manual number Revision

Jul., 2006 IB(NA)-0800354-A First edition

Dec., 2007 IB(NA)-0800354-B

"PLC" was changed to "programmable

controller".

SAFETY PRECAUTIONS, Chapter1,

Section3.1

Sep., 2008 IB(NA)-0800354-C

About Manual, Compliance with the EMC and

Low Voltage Directives, Section3.1

This manual confers no industrial property rights or any rights of any other kind, nor does it

confer any patent licenses. Also, Mitsubishi Electric Corporation cannot be held responsible

for any problems involving industrial property rights which may occur as a result of using the

contents in this manual.

Change of a term

Correction

A-7

CONTENTS

1. OVERVIEW .................................................................................................... 1

2. PERFORAMNCE SPECIFICATIONS............................................................. 2

3. LOADING AND INSTALLATION .................................................................... 3

3.1 Handling Precautions ............................................................................... 3

3.2 Installation Environment ........................................................................... 3

4. PART NAMES ................................................................................................ 4

5. EXTERNAL WIRING ...................................................................................... 6

5.1 Connecting to the 10BASE-T/100BASE-TX............................................. 6

6. SETTING FROM GX DEVELOPER ............................................................... 7

7. EXTERNAL DIMENSIONS ............................................................................. 9

8. TRANSPORTATION PRECAUTIONS.......................................................... 10

8.1 Controlled Model .................................................................................... 10

8.2 Handling for Shipping ............................................................................. 10

A-8

About Manual

The following manual is also related to this product.

In necessary, order it by quoting the details in the table below.

Compliance with the EMC and Low Voltage Directives

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and

Low Voltage Directives when incorporating the Mitsubishi

programmable controller (EMC and Low Voltage Directives

compliant) into other machinery or equipment, refer to Chapter 9

"EMC AND LOW VOLTAGE DIRECTIVES" of the QCPU User's

Manual (Hardware Design, Maintenance and Inspection).

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the programmable

controller.

(2) For the product

For the compliance of this product with the EMC and Low Voltage

Directives, refer to Section 9.1.3 "Cables" in Chapter 9 "EMC AND

LOW VOLTAGE DIRECTIVES" of the QCPU User's Manual

(Hardware Design, Maintenance and Inspection).

Related Manual

Manual name Manual No.

(Model code)

MES Interface Module User's Manual SH-080644ENG

(13JR95)

1. OVERVIEW

This manual explains how to install the QJ71MES96 MES interface

module (hereafter, abbreviated as MES interface module) and how to

wire them with other devices.

(Packing list)

Model Product name Quantity

QJ71MES96 QJ71MES96 MES interface module 1

Battery (Q6BAT) 1

Andere Handbücher für MELSEC Q Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi MELSEC QJ71C24-R2 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q EQ-V680D1 Bedienungsanleitung

Mitsubishi

Mitsubishi FX1N-485-BD Bedienungsanleitung

Mitsubishi

Mitsubishi Melsec FX-4AD Bedienungsanleitung

Mitsubishi

Mitsubishi NZ2GFCF-D62PD2 Bedienungsanleitung

Mitsubishi

Mitsubishi Q64TD Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-FX0N Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX0N-16NT Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Betriebsanleitung

Mitsubishi

Mitsubishi FX-10P-E Installationshandbuch

Mitsubishi

Mitsubishi FX3U-4AD-PNK-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi FX0N-16NT Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F FX1N-40MT-001 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A AJ71E71-S3 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC QS Series Betriebsanleitung

Mitsubishi

Mitsubishi QX10 Bedienungsanleitung

Mitsubishi

Mitsubishi Melsec A Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC L Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-4AD-PT Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Betriebsanleitung

Mitsubishi

Mitsubishi FX3U Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-K Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung