Mitsubishi Q00JCPU Bedienungsanleitung

A- 1

SAFETY PRECAUTIONS

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

DANGER

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in medium or slight personal injury or physical damage.

A- 2

[Design Precautions]

DANGER

Install a safety circuit external to the PLC that keeps the entire system safe even when there are

problems with the external power supply or the PLC module. Otherwise, trouble could result from

erroneous output or erroneous operation.

(1) Outside the PLC, construct mechanical damage preventing interlock circuits such as emergency

stop, protective circuits, positioning upper and lower limits switches and interlocking forward/

reverse operations.

(2) When the PLC detects the following problems,

it will stop calculation and turn off all output in the case of (a).

In the case of (b), it will hold or turn off all output according to the parameter setting.

Note that the AnS/A series module will turn off the output in either of cases (a) and (b).

In addition, all output will be turned on when there are problems that the PLC CPU cannot

detect, such as in the I/O controller. Build a fail safe circuit exterior to the PLC that will make sure

the equipment operates safely at such times.

Refer to "LOADING AND INSTALLATION" in QCPU User's Manual (Hardware Design,

Maintenance and Inspection) for example fail safe circuits.

(3) Output could be left on or off when there is trouble in the outputs module relay or transistor. So

build an external monitoring circuit that will monitor any single outputs that could cause serious

trouble.

Q series module AnS/A series module

(a) The power supply module has

over currentprotection equipment

and over voltage protection

equipment.

Output OFF Output OFF

(b) The CPU module self-diagnosis

functions, such as the watchdog

timer error, detect problems.

Hold or turn off all

output according to

the parameter setting. Output OFF

A- 3

[Design Precautions]

DANGER

When overcurrent which exceeds the rating or caused by short-circuited load flows in the output

module for a long time, it may cause smoke or fire. To prevent this, configure an external safety

circuit, such as fuse.

Build a circuit that turns on the external power supply when the PLC main module power is turned

on.

If the external power supply is turned on first, it could result in erroneous output or erroneous

operation.

When there are communication problems with the data link, refer to the corresponding data link

manual for the operating status of each station.

Not doing so could result in erroneous output or erroneous operation.

When connecting a peripheral device to the CPU module or connecting a personal computer or the

like to the intelligent function module / special function module to exercise control (data change) on

the running PLC, configure up an interlock circuit in the sequence program to ensure that the whole

system will always operate safely.

Also before exercising other control (program change, operating status change (status control)) on

the running PLC, read the manual carefully and fully confirm safety.

Especially for the above control on the remote PLC from an external device, an immediate action

may not be taken for PLC trouble due to a data communication fault.

In addition to configuring up the interlock circuit in the sequence program, corrective and other

actions to be taken as a system for the occurrence of a data communication fault should be

predetermined between the external device and PLC CPU.

CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

When controlling items like lamp load, heater or solenoid valve using an output module, large current

(approximately ten times greater than that present in normal circumstances) may flow when the

output is turned OFF to ON.

Take measures such as replacing the module with one having sufficient rated current.

A- 4

[Installation Precautions]

CAUTION

Use the PLC in an environment that meets the general specifications contained in QCPU User's

Manual (Hardware Design, Maintenance and Inspection).

Using this PLC in an environment outside the range of the general specifications could result in

electric shock, fire, erroneous operation, and damage to or deterioration of the product.

While pressing the installation lever located at the bottom of module, insert the module fixing tab into

the fixing hole in the base unit until it stops. Then, securely mount the module with the fixing hole as

a supporting point.

Incorrect loading of the module can cause a malfunction, failure or drop.

When using the PLC in the environment of much vibration, tighten the module with a screw.

Tighten the screw in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage to the screw or module.

When installing extension cables, be sure that the base unit and the extension module connectors

are installed correctly.

After installation, check them for looseness.

Poor connections could cause an input or output failure.

Securely load the memory card into the memory card loading connector.

After installation, check for lifting.

Poor connections could cause an operation fault.

Completely turn off the externally supplied power used in the system before mounting or removing

the module. Not doing so could result in damage to the product.Note that the module can be

changed online (while power is on) in the system that uses the CPU module compatible with online

module change or on the MELSECNET/H remote I/O station.

Note that there are restrictions on the modules that can be changed online(while power is on), and

each module has its predetermined changing procedure.

For details, refer to QCPU User's Manual (Hardware Design, Maintenance and Inspection) and the

online module change section in the manual of the module compatible with online module change.

Do not directly touch the module's conductive parts or electronic components.

Touching the conductive parts could cause an operation failure or give damage to the module.

A- 5

[Wiring Precautions]

DANGER

Completely turn off the externally supplied power used in the system when installing or placing

wiring.

Not completely turning off all power could result in electric shock or damage to the product.

When turning on the power supply or operating the module after installation or wiring work, be sure

that the module's terminal covers are correctly attached.

Not attaching the terminal cover could result in electric shock.

A- 6

DANGER

Be sure to ground the FG terminals and LG terminals to the protective ground conductor.

Not doing so could result in electric shock or erroneous operation.

Use applicable solderless terminals and tighten them with the specified torque.If any solderless

spade terminal is used, it may be disconnected when the terminal screw comes loose, resulting in

failure.

When wiring in the PLC, be sure that it is done correctly by checking the product's rated voltage and

the terminal layout.

Connecting a power supply that is different from the rating or incorrectly wiring the product could

result in fire or damage.

External connections shall be crimped or pressure welded with the specified tools, or correctly

soldered.

Imperfect connections could result in short circuit, fires, or erroneous operation.

Tighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire, or erroneous operation.

Tightening the terminal screws too far may cause damages to the screws and/or the module,

resulting in fallout, short circuits, or malfunction.

Be sure there are no foreign substances such as sawdust or wiring debris inside the module.

Such debris could cause fires, damage, or erroneous operation.

The module has an ingress prevention label on its top to prevent foreign matter, such as wire offcuts,

from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat dissipation.

Before starting system operation, be sure to peel this label because of heat dissipation. Install our

PLC in a control panel for use. Wire the main power supply to the power supply module installed in a

control panel through a distribution terminal block. Furthermore, the wiring and replacement of a

power supply module have to be performed by a maintenance worker who acquainted with shock

protection. (QCPU User's Manual (Hardware Design, Maintenance and Inspection))

A- 7

[Startup and Maintenance Precautions]

DANGER

Do not touch the terminals while power is on.

Doing so could cause shock or erroneous operation.

Correctly connect the battery.

Also, do not charge, disassemble, heat, place in fire, short circuit, or solder the battery.

Mishandling of battery can cause overheating or cracks which could result in injury and fires.

Switch off all phases of the externally supplied power used in the system when cleaning the module

or retightening the terminal or module mounting screws.

Not doing so could result in electric shock.

Undertightening of terminal screws can cause a short circuit or malfunction.

Overtightening of screws can cause damages to the screws and/or the module, resulting in fallout,

short circuits, or malfunction.

A- 8

[Startup and Maintenance Precautions]

CAUTION

The online operations conducted for the CPU module being operated, connecting the peripheral

device (especially, when changing data or operation status), shall be conducted after the manual has

been carefully read and a sufficient check of safety has been conducted.

Operation mistakes could cause damage or problems with of the module.

Do not disassemble or modify the modules.

Doing so could cause trouble, erroneous operation, injury, or fire.

Use any radio communication device such as a cellular phone or a PHS phone more than 25cm

(9.85 inch) away in all directions of the PLC.

Not doing so can cause a malfunction.

Completely turn off the externally supplied power used in the system before mounting or removing

the module. Not doing so could result in damage to the product.

Note that the module can be changed online (while power is on) in the system that uses the CPU

module compatible with online module change or on the MELSECNET/H remote I/O station.

Note that there are restrictions on the modules that can be changed online (while power is on) , and

each module has its predetermined changing procedure.

For details, refer to QCPU User's Manual (Hardware Design, Maintenance and Inspection) and the

online module change section in the manual of the module compatible with online module change.

Do not mount/remove the module to/from the base unit or terminal block more than 50 times (IEC

61131-2 compliant), after the first use of the product.

Failure to do so may cause module malfunctions.

Do not drop or give an impact to the battery mounted to the module.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before touching the module, always touch grounded metal, etc. to discharge static electricity from

human body, etc.

Not doing so can cause the module to fail or malfunction.

Andere Handbücher für Q00JCPU

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi FX0N-232ADP Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A A2USHCPU-S1 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC F2-60MR Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q EQ-V680D1 Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-32DP Bedienungsanleitung

Mitsubishi

Mitsubishi FREQROL-SFJ Bedienungsanleitung

Mitsubishi

Mitsubishi Q172CPU Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi AJ65BT-R2N-U-HW Bedienungsanleitung

Mitsubishi

Mitsubishi QCPU Betriebsanleitung

Mitsubishi

Mitsubishi MELSEC FX3U-4DA Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC iQ-F FX5 series Betriebsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC F FX-40DU-E Montageanleitung

Mitsubishi

Mitsubishi MELSEC-A AJ35PTC-CNV Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-4LC Bedienungsanleitung

Mitsubishi

Mitsubishi FX1N Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-4AD-PNK-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi FX-2AD-PT Bedienungsanleitung

Mitsubishi

Mitsubishi D700 VFD Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung