Mitsubishi HD8000 Bedienungsanleitung

EN-1

LAN Control Utility

User Manual (for HD8000)

Contents

Preparation/SetUp .........................................................................2

Preparation before using the network function...........................................2

Connection..................................................................................................3

Installation...................................................................................................3

Setting the IP address of the projector .......................................................5

When using a DHCP server ...........................................................................................6

When not using a DHCP server.....................................................................................7

Telnet setting...............................................................................................8

Setting the password (Password Setup) .......................................................................9

Setting the display language of ProjectorView (language) ..........................................10

Setting the LAN control (LAN-Controlled Mode) .........................................................10

Setting the PJLink™ certiﬁcation (PJLink certiﬁcation Mode).....................................11

Save and exit ...............................................................................................................11

ProjectorView...............................................................................12

Using the ProjectorView............................................................................12

How to start up ............................................................................................................12

VIRTUAL REMOTE controller.......................................................................................14

E-mail notiﬁcation function ..........................................................................................14

Initial setting.................................................................................................................15

Support for the PJLink™ function ...............................................16

EN-2

Preparation/SetUp

Preparation before using the network function

This projector is equipped with the network function to control and monitor the projector’s operations using a Web

browser and to send e-mail notiﬁcation.

Before using the network function, perform the following three preparation steps.

(1) Setup of the application software “Projector-Control Device Installer”

(2) Setting of the IP address of the projector *1

(3) Setting of password, display language, LAN control, and PJLink™ certiﬁcation using telnet.

*1 When setting IP addresses for multiple projectors collectively or when setting an IP address for a ceiling-

mounted projector after installation, check and take a note of combination of the projectors and the hardware

addresses (MAC addresses) in advance. To check the hardware addresses (MAC addresses), perform step 2

on the page 5.

[Major functions]

Setting of the projector’s IP address

Setting of password, display language, and LAN control

PJLink™ certiﬁcation setting (Telnet function)

Startup of the controlling / supervising tool (ProjectorView) using the Web browser

[System requirements]

Supported OS : Windows®2000, Windows®XP

(Microsoft®.NET Framework 1.1*2 should be installed.)

CPU : Pentium II 233 MHz or higher

Memory : 128 MB or more

Free HDD space : 32 MB or more

Web browser : Internet Explorer Ver. 6.0

(Java Plug-in*3 should be installed and JavaScript should be enabled.)

*2 How to install Microsoft®.NET Framework Version 1.1

(1) Download .NET Framework Version 1.1 (file named “dotnetfx.exe”) from the download center on the

Microsoft®Web site (http://www.microsoft.com/downloads/).

(When the ﬁle is unavailable from the above-mentioned URL, search for .NET Framework using Windows

Update and access the download site found.)

(2) Execute the downloaded ﬁle named dotnetfx.exe.

*3 How to install Java Plug-in

(1) Download J2SE v1.4.2 JRE from the JAVA download center on the Sun Microsystems Web site (http://java.

sun.com/j2se/1.4.2/download.html).

(When the ﬁle is unavailable from the above-mentioned URL, search for “J2SE download” using a search

engine and access the download site found.)

(2) Execute the downloaded ﬁle.

(3) After the completion of the installation, select [Start] - [Control Panel] - [Java Plug-in] and disable the cache.

• Microsoft or Windows are either registered trademarks or trademarks of Microsoft Corporation in the United

States and/or other countries.

• Pentium is trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and

other countries.

• The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United

States, and other countries and areas.

• Other brand or product names are trademarks or registered trademarks of their respective holders.

EN-3

Copy three ﬁles (DI_4.1.3.4.msi, Setup.Exe, and Setup.Ini) contained in the Tools folder of CD-ROM to the

hard disk of your personal computer.

Double-click the ﬁle named Setup.Exe.

When the following window appears, click Next.

Installation

Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.

Connection

• Use a straight-through category-5 cable for LAN connection.

• Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged

from your body, causing damage to the projector.

Preparation/SetUp (continued)

Computer

To LAN terminal

LAN cable (option)

(100BASE-TX or 10BASE-T should be supported.)

LAN cable (option)

(100BASE-TX or 10BASE-T

should be supported.)

External HUB

EN-4

Preparation/SetUp (continued)

Select a folder to install the program, and click Next.

Click Next.

Installation starts.

• The progress of the installation process is

displayed as shown on the right.

When the installation process is completed, click

Close.

How to remove Projector-Control Device Installer

Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click [Remove]

(in the case of Windows®XP).

EN-5

Start the Projector-Control Device Installer.

• Select [Start] - [All Programs] - [Projector] -

[Projector-Control Device Installer] (in the case of

Windows®XP).

Click the Search button.

• Projector is recognized.

(Note)

When projector isn’t recognized, check the following.

• The ﬁrewall function has been disabled. (When it

has been enabled, search may not be conducted.)

• The personal computer and the projector are on

the same network. (For preventing unauthorized

access.)

• More than one Projector-Control Device Installer

isn’t running.

Select a projector by clicking the line showing the

projector and click the Assign IP button.

Click here

(Don’t select this side. When you

execute IP assignment with this side

selected, it may become impossible to

control the projector.)

The Assign IP Address screen appears.

Setting the IP address of the projector

Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the

projector.

• When using multiple projectors, connect and configure them one by one. If you turn on the powers of the

projectors that are connected but not yet conﬁgured at the same time, they may not be recognized.

• For automatic IP address setting by the DHCP server, go to page 6. For IP address setting without using the

DHCP server, go to page 7.

Preparation/SetUp (continued)

EN-6

Select [Obtain an IP address automatically] and click

Next.

Click Next.

• Check that the options are marked with check-

marks as shown on the right. Keep them un-

changed for normal use.

Click Assign.

Click Finish.

Click the Search button.

• Check the IP address.

When using a DHCP server

Preparation/SetUp (continued)

EN-7

Select [Assign a speciﬁc IP address] and click Next.

Enter a ﬁxed IP address (for example, 192.168.0.1)

and click Next.

(Note)

Do not use 0 or 255 for the last digit of the IP

address.

Click Assign.

Click Finish.

Click the Search button.

• Check the IP address you set.

(Note)

When using the error/alert e-mail notiﬁcation function

described later, click the Assign IP button and set the

subnet mask and default gateway correctly.

• For the values of the subnet mask and default

gateway, contact your network administrator.

When not using a DHCP server

Preparation/SetUp (continued)

EN-8

Start the Projector-Control Device Installer.

• Select [Start] - [All Programs] - [Projector] -

[Projector-Control Device Installer] (in the case of

Windows®XP).

Press the + buttons on the left pane to expand the

tree structure until the IP address you set appears.

Click the Telnet Conﬁguration tab.

Select the Connect tab. Press the Enter key within

5 seconds after the message shown on the right

appears.

• When it passes 5 seconds without any operation

on this screen, the screen is shaded and no key

operation is accepted. In this case, click the

Connect button again to continue setting.

The setting menu appears.

Telnet setting

Setting of password, display language, LAN control, and PJLink™ certiﬁcation using telnet.

This section describes how to set the password, display language on the ProjectorView screen, LAN control, and

PJLink™ certiﬁcation that are necessary for the operation state control tool (commercially available) that uses the

projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol.

Preparation/SetUp (continued)

EN-9

Enter “0” and press the Enter key.

Input the old (current) password and press the Enter

key. (Default password is admin.)

• If you input a wrong password, an error message

appears and the setting menu is displayed again.

In this case, set the password again.

• If you forget your password, select “7 factory

defaults,” input the password “projectorcontroller,”

and then select “9 save and exit” to perform

initialization.

Input a new password (example: “proj2000”) and

press the Enter key.

(Note)

Use single-byte alphanumeric characters only.

Input the new password (example: “proj2000”) again

and press the Enter key.

• If you input a wrong password, an error message

appears and the setting menu is displayed again.

In this case, set the password again.

Setting the password (Password Setup)

Preparation/SetUp (continued)

EN-10

Enter “3” and press the Enter key.

To enable the e-mail notiﬁcation function of Projector-

View, enter 1 and press the Enter key. (Default is OFF (0).)

(See pages 12 - 15 for ProjectorView function.)

Setting the LAN control (LAN-Controlled Mode)

Preparation/SetUp (continued)

Enter “1” and press the Enter key.

Enter “0” for English or “1” for Japanese.

Setting the display language of ProjectorView (language)

Andere Handbücher für HD8000

Inhaltsverzeichnis

Andere Mitsubishi Projektor Handbücher

Mitsubishi

Mitsubishi HC4000 Bedienungsanleitung

Mitsubishi

Mitsubishi HC900U Bedienungsanleitung

Mitsubishi

Mitsubishi HC100U Bedienungsanleitung

Mitsubishi

Mitsubishi LVP-XD10U Bedienungsanleitung

Mitsubishi

Mitsubishi HD8000 Bedienungsanleitung

Mitsubishi

Mitsubishi S290U Bedienungsanleitung

Mitsubishi

Mitsubishi DLP XD1000U Bedienungsanleitung

Mitsubishi

Mitsubishi HC2000 Bedienungsanleitung

Mitsubishi

Mitsubishi XD8100LU Bedienungsanleitung

Mitsubishi

Mitsubishi HC6800 Bedienungsanleitung

Mitsubishi

Mitsubishi DLP EW331U-ST Bedienungsanleitung

Mitsubishi

Mitsubishi X70B Bedienungsanleitung

Mitsubishi

Mitsubishi SD110R Bedienungsanleitung

Mitsubishi

Mitsubishi X300 Bedienungsanleitung

Mitsubishi

Mitsubishi XL2U Bedienungsanleitung

Mitsubishi

Mitsubishi HD8000 Gebrauchs- und Wartungshandbuch

Mitsubishi

Mitsubishi HC7000 Bedienungsanleitung

Mitsubishi

Mitsubishi WD620U Bedienungsanleitung

Mitsubishi

Mitsubishi X100 Bedienungsanleitung

Mitsubishi

Mitsubishi VS-1281 Bedienungsanleitung

Mitsubishi

Mitsubishi LVP-X250U Bedienungsanleitung

Mitsubishi

Mitsubishi XL5900LU Gebrauchs- und Wartungshandbuch

Mitsubishi

Mitsubishi SL4SU Bedienungsanleitung

Mitsubishi

Mitsubishi SD510U Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung