Mitsubishi F940 Bedienungsanleitung

HARDWARE MANUAL

F940GOT-SWD-E/LWD-E

[Connection System Manual]

JY992D79201A(MEE9903)

F940GOT-SWD-E/LWD-E

HARDWARE MANUAL

(Connection System Manual)

Manual number : JY992D79201

Manual revision : A

Date : March 1999

F940GOT-SWD-E/LWD-E

Guidelines for the safety of the user and protection of the F940GOT-SWD-E/LWD-E

This manual provides information for the installation and use of the Graphic Operation Terminal F940GOT.

The manual has been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows;

a ) Any engineer who is responsible for the planning, design and construction of automatic equipment

using the product associated with this manual should be of a competent nature, (trained and qualified

to the local and national standards required to fulfill that role). These engineers should be fully aware

of safety with regards to automated equipment.

b ) Any commissioning or service engineer must be of a competent nature, trained and qualified to the

local and national standards required to fulfill that job. These engineers should also be trained in the

use and maintenance of the completed product. This includes being completely familiar with all asso-

ciated documentation for the said product. All maintenance should be carried out in accordance with

established safety practices.

c ) All operators of the compliance product should be trained to use that product in a safe and coordi-

nated manner in compliance to established safety practices. The operators should also be familiar

with all documentation which is connected with the actual operation of the completed equipment.

Note:The term ‘completed equipment’ refers to a third party constructed device which contains or uses the

product associated with this manual.

F940GOT-SWD-E/LWD-E

iii

Note’s on the symbology used in this manual

At various times through out this manual certain symbols will be used to highlight points of information which

are intended to ensure the users personal safety and protect the integrity of the equipment. Whenever any of

the following symbols are encountered, its associated note must be read and understood. Each of the sym-

bols used will now be listed with a brief description of its meaning.

Hardware warnings

Software warnings

1 ) Indicates that the identified danger WILL cause physical and property damage.

2 ) Indicates that the identified danger POSSIBLY cause physical and property damage.

3 ) Indicates a point of further interest or further explanation.

1 ) Indicates special care must be taken when using this element of software.

2 ) Indicates a special point of which the user of the associate software element should be aware.

3 ) Indicates a point of interest or further explanation.

F940GOT-SWD-E/LWD-E

MEMO

Table of Contents

1. System configuration...........................................................................1-1

1.1 When the GOT is directly connected to the PLC.............................................1-1

1.2 When built-in two-port interface function is used ............................................1-3

2. Connection to personal computer.......................................................2-1

2.1 Pin assignment and connection diagram of transfer cables ............................2-2

3. CPU port connection...........................................................................3-1

3.1 Connection to FX/A Series...............................................................................3-1

3.2 Connection diagram.........................................................................................3-3

3.3 Connection of two or more GOT units .............................................................3-4

4. Computer link port connection (MELSEC A Series)............................4-1

4.1 Connection diagram.........................................................................................4-2

5. Connection to SYSMAC C Series.......................................................5-1

5.1 Connection diagram.........................................................................................5-2

6. Connection to FLEX-PC N Series.......................................................6-1

6.1 Connection diagram.........................................................................................6-2

7. Connection by general-purpose communication.................................7-1

7.1 Outline..............................................................................................................7-1

7.2 Connection diagram.........................................................................................7-3

7.3 Communication setting ....................................................................................7-4

F940GOT-SWD-E/LWD-E

System configuration 1.

1-1

1. System configuration

The system configuration to use the GOT is described below.

1.1 When the GOT is directly connected to the PLC

(When the GOT is connected via a computer link unit, refer to Section 2.)

F940GOT-SWD-E/LWD-E Data transfer cable FX-232CAB-1 (when the RS-232C connector in the personal

computer is 9-pin type) or Data transfer cable FX-232CAB-2 (when the RS-232C

connector in the personal computer is half-pitch,14-pin type)

Attach a ROM to the F9GT-40UMB, then connect it to a connector provided on the rear

face of the GOT.

FX/FX

Series

A Series (except QnA)

Motion controller

/FX

2NC

Series

Connection cable FX-40DU-CAB *1

It cannot be used when a computer link (RS-232C communication) is used.

Connection cable FX-

50DU-CAB0 for CPU

port connection*1

Data transfer cable F2-232CAB-1

*1 Connection cables of different length are available.

F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E System configuration 1.

1-2

Printer

< Dedicated printers >

GT-10A

K6PR(-K), A7(N)PR

< General-purpose printers >

ESC/P

Printer equipped with RS-232C interface

(Prints out sampling data, alarm history and alarm messages.)

General-purpose personal computer

(screen creation software)

Peripheral units for GOT

EPROM memory

FX-EPROM-4M

ROM writer

General-purpose ROM writer

(User screen data can be written

using a general-purpose ROM writer.)

Data transfer cable F2-232CAB-1

(when the RS-232C connector in the

personal computer is 25-pin type)

Connected to RS-232C connector in GOT

Screen creation software for DU

FX-PCS-DU/WIN-E (V2.10 or later)

Screen creation software for A900GOT

SW D5C-GOTRE-PACK

(" " is a numeric not less than 1.)

F940GOT-SWD-E/LWD-E System configuration 1.

1-3

The figure below shows connection to peripheral units used to create sequence programs.

1.2 When built-in two-port interface function is used

F940GOT-SWD-E/LWD-E

Data transfer cable FX-232CAB-1

(when the RS-232C connector in the personal computer is 9-pin type)

When the two-port interface function is used, the operation environment should be set.

(Refer to the description on "SERIAL PORT" on the SET-UP MODE screen.)

Data transfer cable F2-232CAB-2

(when the RS-232C connector in the personal computer is half-pitch, 14-pin type)

Connected to RS-232C connector in GOT

FX/FX

Series

A Series (except QnA)

Motion controller

/FX

2NC

Series

Connection cable FX-40DU-CAB *1

Connection cable FX-

50DU-CAB0 for CPU

port connection*1

*1 Connection cables of different length are available.

Andere Handbücher für F940

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Touch-Terminal Handbücher

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Bedienungsanleitung

Mitsubishi

Mitsubishi GT10 Bedienungsanleitung

Mitsubishi

Mitsubishi GOT2000 Series Gebrauchsanweisung

Mitsubishi

Mitsubishi GT16 Bedienungsanleitung

Mitsubishi

Mitsubishi GT1040-QBBD Bedienungsanleitung

Mitsubishi

Mitsubishi F930GOT-BBD-K-E Bedienungsanleitung

Mitsubishi

Mitsubishi GT1275-VNBA Bedienungs- und Montageanleitung

Mitsubishi

Mitsubishi MELSEC GOT-F900 Bedienungsanleitung

Mitsubishi

Mitsubishi F940 Bedienungsanleitung

Mitsubishi

Mitsubishi F940GOT Handy Series Bedienungsanleitung

Mitsubishi

Mitsubishi GT16 Bedienungsanleitung

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Bedienungsanleitung

Mitsubishi

Mitsubishi GT1150-QLBD Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 Series Gebrauchsanweisung

Mitsubishi

Mitsubishi GOT-A900 Series Bedienungsanleitung

Mitsubishi

Mitsubishi F940GOT-SWD-E Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 GT15 Bedienungsanleitung

Mitsubishi

Mitsubishi GT16 Bedienungsanleitung

Mitsubishi

Mitsubishi GT11 Bedienungsanleitung

Mitsubishi

Mitsubishi GT14 Bedienungsanleitung

Mitsubishi

Mitsubishi A950GOT Bedienungsanleitung

Mitsubishi

Mitsubishi 900 Series Bedienungsanleitung

Mitsubishi

Mitsubishi F930GOT-BBD-K-E Bedienungsanleitung

Mitsubishi

Mitsubishi GT10 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung